XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

有線接続

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

診断上の注意

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

QRコードをスキャンするか、
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
ダウンロードしたファイルを解凍する file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

使い方
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

商標
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

保証の否認および責任の制限
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

サポートとサービス

正式 Webサイト： www.xtooltech.com
メールアドレス: xtoolinplusus@outlook.com

概要

展望とポート

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

インジケーターライトの色	インジケーターライト意味
緑色の点灯	電源が入っています
点滅する緑色のライト	ファームウェアの更新
青色点灯	Device connected (no communication)
点滅する青い光	Communicating with the vehicle
点滅する赤信号	デバイスの障害

はじめる

車両接続

ワイヤレス接続

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

有線接続

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

診断上の注意

巻tag車の範囲: +9~+36V DC;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
さまざまなモデルの電子制御システムは非常に複雑です。テストできない状況や大量のテストデータに異常がある場合は、車両の ECU を検索し、ECU 銘板にあるモデルのメニューを選択できます。
車両またはデバイスの損傷を防ぐため、このデバイスでは、XTOOL が提供し、デバイス用に設計された配線ハーネスのみを使用できます。
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

インストール

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

使い方

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

メイン画面
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

設定

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

フィードバック

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

あなたのメールアドレス
ログ files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

FCC準拠

FCC ID: 2AW3IV01W2

このデバイスは、FCC 規則のパート 15 に準拠しています。操作には次の XNUMX つの条件が適用されます。

このデバイスは有害な干渉を引き起こすことはありません
このデバイスは、望ましくない動作を引き起こす可能性のある干渉を含め、受信したあらゆる干渉を受け入れる必要があります。

警告
コンプライアンス責任者によって明示的に承認されていない変更または修正を行うと、ユーザーの機器の操作権限が無効になる可能性があります。

注記
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

受信アンテナの向きを変えるか、位置を変えてください。
機器と受信機間の距離を広げます。
受信機が接続されている回路とは別のコンセントに機器を接続します。
販売店または経験豊富なラジオ/テレビ技術者にご相談ください。

責任者

会社名: FCC US Agent, LLC
住所: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
メールアドレス: Support@FCCUSAgent.com

ISED 声明

IC: 29441-V01W2
Model: XTS500
PMN: V120，XTS500
HVIN: V01W2A

このデバイスには、カナダのイノベーション、科学、経済開発省のライセンス免除 RSS に準拠したライセンス免除の送信機/受信機が含まれています。操作には次の 2 つの条件が適用されます。

このデバイスは干渉を引き起こすことはありません。
このデバイスは、デバイスの望ましくない動作を引き起こす可能性のある干渉を含め、あらゆる干渉を受け入れる必要があります。

適合宣言
深圳XTOOLtech Intelligent Co., Ltd.は、本無線診断モジュールが指令2014/53/EUの必須要件およびその他の関連規定に準拠していることをここに宣言します。第10条(2)および第10条(10)に基づき、本製品はすべてのEU加盟国で使用できます。

イギリスCA

ここに、Shenzhen XTOOLtech Intelligent Co., Ltd は、このワイヤレス診断モジュールが、英国無線機器規制 (SI 2017/1206)、英国電気機器 (安全) 規制 (SI 2016/1101)、および英国電磁両立性規制 (SI 2016/1091) の範囲内で製品に適用されるすべての技術規制を満たしていることを宣言し、同じ申請が他の英国認定機関に提出されていないことを宣言します。
深セン Xtooltech インテリジェント株式会社
住所: 中国深圳市南山区柳仙大道クリエイティブシティA17ビル18階と2階
深セン本社電話: +86 755 2399608
メールアドレス: マーケティング@ xtooltech.com

よくある質問

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

ドキュメント / リソース

XTOOL XTS500 Wireless Diagnostics Module [pdf] ユーザーマニュアル
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

参考文献

ユーザーマニュアル

XTOOL XTS500 Wireless Diagnostics Module

仕様

製品使用説明書

概要