Xlink-LOGO

Xlink TCS100 TPMS Sensor

Xlink-TCS100-TPMS-Sensor-PRODUCT

製品仕様

  • モデル: TCS100 Sensor
  • 互換性: ユニバーサル
  • 材料: ステンレス鋼
  • 電源: 電池式
  • 測定範囲: 0~100ユニット

安全に関する注意事項

Before using the TCS100 Sensor, please read and follow these safety instructions:

  1. Always wear appropriate protective gear when handling the sensor.
  2. Avoid exposing the sensor to extreme temperatures or moisture.
  3. Do not disassemble the sensor yourself; contact a qualified technician for any repairs.

パラメータ

The TCS100 Sensor comes with the following parameters.

  • 正確さ: +/- 2%
  • 動作温度: 0〜50℃
  • 解決: 0.1 ユニット

Sensor Component Diagram

The diagram below illustrates the components of the TCS100 Sensor for your reference:

インストール操作手順

  1. ステップ1: ノズルをハブに通し、ノズル固定ナットで固定します。 締め付けていないことに注意してください。

製品使用説明書

  1. Ensure the sensor is properly connected to the power source.
  2. Calibrate the sensor based on your specific measurement requirements.
  3. Place the sensor in the desired location for accurate readings.

安全に関する注意事項

  • 製品をご使用になる前に、このマニュアルをよくお読みになり、製品の構造をよく理解し、製品の取り付け方法をマスターしてください。 取り付ける前に、製品の付属品が完成し、製品が正常に動作し、異常な外観や構造がないことを確認してください。 設置の際、会社は保守作業の仕様を厳守し、専門の保守ツールを使用するものとします。 それ以外の場合、当社はお客様の違法な操作により生じたいかなる問題についても責任を負いません。 製品の使用過程で問題が発生した場合は、すぐに交換または停止し、専門の保守担当者またはアフターサービスでテストする必要があります。 製品を取り付けた後は、安全上のリスクを排除するために、タイヤの動的バランスを必ず再測定してください。

パラメータ

  • 製品モデル: TCS-100
  • 保管温度:-10℃〜50℃
  • 動作温度:-40℃〜125℃
  • 圧力監視範囲:0〜900Kpa
  • Waterproof grade: IP67
  • 電池寿命:3~5歳
  • パワーレベル:-33.84d Bm
  • 周波数:314.9MHz
  • 圧力精度: ±7Kpa
  • 温度精度:±3℃
  • 重さ :26g(バルブ付)
  • 寸法:約72.25mm * 44.27mm * 17.63mm
  • 保証: 2年

センサーコンポーネント図

Xlink-TCS100-TPMS-Sensor-FIG-1

インストール操作手順

  1. ステップ1: ノズルをハブに通し、ノズル固定ナットで固定します。 締め付けていないことに注意してください。Xlink-TCS100-TPMS-Sensor-FIG-2
  2. ステップ2: センサー固定ネジでエアノズルにセンサーを固定します。 センサーは4N•mのトルクでハブの近くにある必要があることに注意してください。Xlink-TCS100-TPMS-Sensor-FIG-3
  3. ステップ3: エアノズル固定ナットをレンチで締めて取り付けを完了します。 レンチは7N•mのトルクを使用することに注意してください。Xlink-TCS100-TPMS-Sensor-FIG-4

連邦通信委員会

このデバイスは、FCC 規則のパート 15 に準拠しています。操作には次の XNUMX つの条件が適用されます。

  1. このデバイスは有害な干渉を引き起こすことはありません。
  2. このデバイスは、望ましくない動作を引き起こす可能性のある干渉を含め、受信したあらゆる干渉を受け入れる必要があります。

コンプライアンス責任者によって明示的に承認されていない変更または修正を行うと、ユーザーの機器の操作権限が無効になる可能性があります。
注記: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • 受信アンテナの向きを変えるか、位置を変えてください。
  • 機器と受信機間の距離を広げます。
  • 受信機が接続されている回路とは別のコンセントに機器を接続します。
  • 販売店または経験豊富なラジオ/テレビ技術者にご相談ください。

よくある質問

  • Q: How often should I calibrate the TCS100 Sensor?
    • A: It is recommended to calibrate the sensor every three months for optimal performance.
  • Q: センサーは屋外環境でも使用できますか?
    • A: The sensor is designed for indoor use; avoid exposing it to outdoor conditions to prevent damage.

ドキュメント / リソース

Xlink TCS100 TPMS Sensor [pdf] 説明書
TCS100, TCS100 TPMS Sensor, TPMS Sensor, Sensor

参考文献

コメントを残す

あなたのメールアドレスは公開されません。 必須項目はマークされています *