Sharp AndroidTVユーザーガイド

Sharp-Android-TV

シャープなAndroidTV

 

重要な安全上の注意事項


機器を操作する前に、これらの安全に関する指示を読み、以下の警告を守ってください。

文章

  • 43インチ以上の画面を備えたテレビは、少なくともXNUMX人で持ち上げて持ち運ぶ必要があります。
  • このテレビには、ユーザーが修理できる部品は含まれていません。 故障の場合は、メーカーまたは認定サービス代理店にご連絡ください。 テレビ内の特定の部品との接触は、あなたの生命を危険にさらす可能性があります。 保証は、許可されていない第三者によって行われた修理によって引き起こされた障害には適用されません。
  • 機器の背面部分を取り外さないでください。
  • このアプライアンスは、ビデオの受信と再生用に設計されています
    と音の信号。 その他の使用は固く禁じられています。
  • テレビに液体が滴ったり飛び散ったりしないようにしてください。
  • テレビを主電源から外すには、主電源プラグをから外してください。
    メインソケット。 ・供給コードが損傷している場合は、危険を回避するために、製造元、サービス代理店、または同様の資格のある人が交換する必要があります。
  • HD TVを視聴するための推奨距離は、画面の対角サイズの約XNUMX倍です。 他の光源からの画面上の反射は、画像の品質を悪化させる可能性があります。
  • テレビに十分な換気があり、他の電化製品や他の家具の近くにないことを確認してください。
  • 通気のため、壁から5cm以上離して設置してください。
  • 換気口に新聞紙、テーブルクロス、カーテンなどの物が置かれていないことを確認してください。
  • このテレビは温暖な気候での使用を想定して設計されています。
  • テレビは乾燥した場所での操作専用に設計されています。 テレビを屋外で使用する場合は、湿気(雨、水しぶき)から保護してください。 湿気にさらさないでください。
  • テレビの上に物や花瓶などの液体が入った容器を置かないでください。 これらの容器は押し倒され、電気の安全を脅かす可能性があります。 テレビは平らで安定した面にのみ置いてください。 新聞や毛布などをテレビの上や下に置かないでください。
  • 機器を電源ケーブルの上に置かないでください。電源ケーブルが損傷する可能性があります。携帯電話や WLAN アダプター、ワイヤレス信号伝送を備えた監視カメラなどのデバイスは、電磁干渉を引き起こす可能性があるため、機器の近くに置かないでください。
  • アプライアンスの冷却に悪影響を与えるため、アプライアンスを発熱体の近くや直射日光の当たる場所に置かないでください。 蓄熱は危険であり、アプライアンスの寿命を大幅に短縮する可能性があります。 安全を確保するために、資格のある人にアプライアンスの汚れを取り除くよう依頼してください。
  • 電源ケーブルまたは電源アダプタの損傷を防ぐようにしてください。機器は付属の電源ケーブル/アダプタでのみ接続できます。
  • 嵐はすべての電化製品にとって危険です。 主電源や空中配線に照明を当てると、電源を切ってもアプライアンスが損傷する可能性があります。 嵐が発生する前に、アプライアンスのすべてのケーブルとコネクタを外す必要があります。
  • 機器のスクリーンを清掃するには、広告のみを使用してくださいamp 柔らかい布で拭いてください。きれいな水のみを使用してください。洗剤や溶剤は絶対に使用しないでください。
  • テレビを押したときに落ちる可能性を回避するために、テレビを壁の近くに配置します。
  • 警告 –不安定な場所にテレビを置かないでください。 テレビが落下し、重傷を負ったり死亡する恐れがあります。 特に子供に対する多くの怪我は、次のような簡単な予防策を講じることで回避できます。
  • テレビメーカーが推奨するキャビネットまたはスタンドを使用してください。
  • テレビを安全に支えることができる家具のみを使用してください。 ・テレビがサポート家具の端からはみ出していないことを確認します。
  • テレビを背の高い家具の上に置かないでください(例:amp家具とテレビの両方を適切なサポートに固定せずに、テレビ台(食器棚や本棚など)の上に設置することはできません。
  • テレビとそれを支える家具の間に布やその他の素材を置かないでください。
  • テレビやそのコントローラーに届くように家具に登ることの危険性について子供たちに教育します。
  • お子様がテレビに登ったり、ぶら下がったりしないように注意してください。
  • 既存のテレビをそのまま残して移動する場合は、上記と同じ考慮事項を適用する必要があります。
  • 以下に示す手順は、テレビを壁に固定することで、テレビをより安全にセットアップする方法であり、テレビが前に倒れて怪我や損傷を引き起こす可能性を回避します。
  • このタイプの設置には、固定コードが必要です。A)上部の壁取り付け穴とネジ(ネジは壁取り付け穴にすでに付属しています)の一方または両方を使用して、固定コードの一方の端をテレビに固定します。 。 B)固定弦のもう一方の端を壁に固定します。
  • テレビのソフトウェアおよび OSD レイアウトは予告なく変更される場合があります。
  • 注記: 静電放電(ESD)の場合、装置は誤った機能を示す可能性があります。 このような場合は、テレビの電源をオフにしてからオンに戻してください。 テレビは正常に動作します。

警告:

  • セットをオフにするときは、リモコンのスタンバイボタンを使用してください。 このボタンを長押しすると、テレビの電源が切れ、省エネスタンバイモードになり、エコデザインの要件を満たします。 このモードはデフォルトです。
  • テレビは開梱後すぐに使用しないでください。テレビが室温に温まるまで待ってから使用してください。
  • 通電中の機器に外部デバイスを絶対に接続しないでください。テレビだけでなく、接続されているデバイスの電源も切ってください。外部デバイスとアンテナを接続した後は、テレビのプラグを壁のコンセントに差し込んでください。
  • テレビの電源プラグに無料でアクセスできることを常に確認してください。 ・アプライアンスは、
    モニター。
  • 大音量でヘッドフォンを継続的に使用すると、回復不可能な聴覚障害を引き起こす可能性があります。
  • このアプライアンスとすべてのコンポーネントの環境廃棄を確実にする
    電池を含む。 不明な点がある場合は、リサイクルの詳細について地方自治体にお問い合わせください。
  • アプライアンスを設置する際は、家具の表面がさまざまなワニスやプラスチックなどで処理されていることを忘れないでください。そうしないと、磨かれる可能性があります。 これらの製品に含まれる化学物質は、テレビ台と反応する可能性があります。 これにより、家具の表面に材料の一部が付着する可能性があります。これは、不可能ではないにしても、取り除くのが困難です。
  • テレビの画面は最高品質の条件下で作成されており、ピクセルの欠陥がないか詳細に数回チェックされています。 製造工程の技術的特性により、画面上の少数の欠陥点の存在を排除することはできません(製造中に最大限の注意を払っても)。 これらの障害のあるピクセルは、その範囲がDIN規格で定義された境界よりも大きくない場合、保証条件の観点から障害とは見なされません。
  • 製造元は、サードパーティのコンテンツまたはサービスに関連するカスタマーサービス関連の問題について責任を負わないものとします。 サードパーティのコンテンツまたはサービスに関する質問、コメント、またはサービス関連の問い合わせは、該当するコンテンツまたはサービスプロバイダーに直接行う必要があります。
  • 停電、インターネット接続、デバイスの正しい構成の失敗など、デバイス自体に関係のないデバイスからコンテンツやサービスにアクセスできない理由はさまざまですが、これらに限定されません。 UMCポーランド、その取締役、役員、従業員、代理人、請負業者、および関連会社は、そのような障害または保守に関して、お客様または第三者に対して責任を負わないものとします。tag原因や回避可能であったかどうかに関係なく、発生します。
  • このデバイスを介してアクセス可能なすべてのサードパーティのコンテンツまたはサービスは、「現状有姿」および「利用可能な範囲」で提供され、UMCポーランドおよびその関連会社は、明示または黙示を問わず、いかなる種類の保証または表明も行いません。 、商品性、非侵害、特定の目的への適合性の保証、または適合性、可用性、正確性、完全性、セキュリティ、タイトル、有用性、過失の欠如、エラーのない、または中断のない操作または使用の保証。お客様に提供されるコンテンツまたはサービス、またはコンテンツまたはサービスがお客様の要件または期待を満たすこと。
  • UMCポーランドは、サードパーティのコンテンツまたはサービスプロバイダーの作為または不作為、あるいはそのようなサードパーティプロバイダーに関連するコンテンツまたはサービスのいかなる側面の代理人でも責任も負いません。
  • いかなる場合も、「UMCポーランド」および/またはその関連会社は、責任の理論が契約、不法行為に基づいているかどうかにかかわらず、直接的、間接的、特別、偶発的、懲罰的、結果的またはその他の損害について、あなたまたは第三者に対して責任を負わないものとします。過失、保証違反、厳格責任など、およびUMCポーランドおよび/またはその関連会社がそのような損害の可能性について知らされているかどうか。
  • この製品には、Microsoft の特定の知的財産権の対象となるテクノロジが含まれています。Microsoft からの適切なライセンスがない限り、このテクノロジをこの製品以外で使用または配布することは禁止されています。
  • コンテンツ所有者は、著作権で保護されたコンテンツを含む知的財産を保護するために、Microsoft PlayReadyTM コンテンツ アクセス テクノロジを使用します。このデバイスは、PlayReady テクノロジを使用して、PlayReady で保護されたコンテンツや WMDRM で保護されたコンテンツにアクセスします。デバイスがコンテンツの使用制限を適切に適用できない場合、コンテンツ所有者は、Microsoft に対して、PlayReady で保護されたコンテンツを使用するデバイスの機能を取り消すように要求できます。取り消しは、保護されていないコンテンツや他のコンテンツ アクセス テクノロジによって保護されているコンテンツには影響しません。コンテンツ所有者は、コンテンツにアクセスするために PlayReady のアップグレードを要求する場合があります。アップグレードを拒否すると、アップグレードを必要とするコンテンツにアクセスできなくなります。

ビデオゲーム、コンピューター、キャプション、その他の固定画像ディスプレイの使用に関する重要な情報。

  • 固定画像プログラム素材を長期間使用すると、LCD画面に永続的な「シャドウ画像」が発生する可能性があります(これは、誤って「画面のバーンアウト」と呼ばれることがあります)。 この影の画像は、背景の画面に永続的に表示されます。 不可逆的なダメージです。 以下の手順に従って、このような損傷を回避できます。
  • 明るさ/コントラストの設定を最小にする viewingレベル。 ・固定画像を長時間表示しないでください。 以下の表示は避けてください。

» 文字放送の時間とチャート、
» TV / DVDメニュー、例:DVDコンテンツ、
» 、、一時停止」モード(長押し)の場合:DVDやビデオを見ているときなど、このモードを長時間使用しないでください。
» 使用しない場合は、アプライアンスの電源を切ってください。

バッテリー

  • 電池を挿入する際は正しい極性に注意してください。
  • バッテリーを高温にさらさないでください。また、火の近くや直射日光の当たる場所など、温度が急激に上昇する可能性のある場所に置かないでください。
  • バッテリーを過度の輻射熱にさらさないでください。Cdはバッテリーを火の中に投げ入れたり、分解したり、充電できないバッテリーを充電しようとしたりしないでください。 漏れたり爆発したりする可能性があります。

» 異なる電池を一緒に使用したり、新しい電池と古い電池を混ぜて使用しないでください。
» バッテリーは環境に優しい方法で廃棄してください。
» EU諸国のほとんどは、法律によってバッテリーの廃棄を規制しています。

廃棄

  • このテレビを分別されていない都市ごみとして処分しないでください。 WEEEのリサイクルのために、指定された収集場所に返送してください。 そうすることで、資源を節約し、環境を保護するのに役立ちます。 詳細については、販売店または地方自治体にお問い合わせください。

CE ステートメント:

  • これにより、UMCポーランドSp。 z ooは、このLEDTVがRED指令2014/53 / EUの必須要件およびその他の関連規定に準拠していることを宣言します。 EU適合宣言の全文は、リンクをたどって入手できます。 www.sharpconsumer.eu/documents-of-conformity/ この機器は、すべてのEU諸国で運用できます。 この機器の5GHz WLAN(Wi-Fi)機能は、屋内でのみ操作できます。

Wi-Fi 最大送信電力:

100GHzで2,412mW 2,472 GHz
100GHzで5,150mW 5,350 GHz
100GHzで5,470mW 5,725 GHz
BT最大送信機電力:10 GHz 2,402GHzで2,480mW。

箱に何が含まれているか

このテレビには以下の部品が含まれています:

  • 1xテレビ
  • 1xTVスタンド取り付けパケット
  • リモコン x 1
  • 1xクイックスタートクイド
  • 単2電池XNUMX本
  • 1xウォールマウントセット(4x M6x35ネジと4xプラスチックスペーサー)*

* –50インチモデルでのみ使用可能

スタンドの取り付け

アクセサリーバッグにあるテクニカルリーフレットの指示に従ってください

テレビを壁に取り付ける

  1. 壁取り付け穴に付属しているXNUMX本のネジを外します。
  2. ウォールマウントは、テレビの背面にある取り付け穴に簡単に取り付けることができます。
  3. ブラケットの製造元のアドバイスに従って、壁取り付けブラケットをテレビに取り付けます。

50インチモデルに壁取り付けブラケットを取り付ける場合は、TV壁取り付け穴にあるネジの代わりに、アクセサリパックに含まれている長いネジとスペーサーを使用することをお勧めします。 テレビの背面にあるテレビの壁取り付け穴にスペーサーを入れてから、壁掛けブラケットを取り付けてください。 以下に示すように、長いネジを使用してブラケットとスペーサーをテレビに取り付けます。
図

  1. TV
  2. スペーサー
  3. スクリュー

注記: 図に示されているテレビと壁掛けブラケットのタイプは、説明のみを目的としています。

接続

外部デバイスの接続は、このIMの最後のページを参照してください。

はじめに – 初期設定

  1. RFケーブルを使用して、TVをTVAerialウォールソケットに接続します。
  2. 有線接続でインターネットに接続するには、Cat 5 /イーサネットケーブル(別売)をテレビからブロードバンドモデム/ルーターに接続します。
  3. 付属の電池をリモコンに挿入します。
  4. 電源ケーブルをコンセントに接続します。
  5. 次に、スタンバイボタンを押してテレビの電源を入れます。
  6. テレビの電源を入れた後、あなたはによって歓迎されます 初回インストールメニュー。
  7. TVメニューの言語を選択してください。
  8. 初回インストールメニューの残りの画面で希望の設定をしてください。

テレビボタン*

巻+ 音量を上げてメニューを右に
Vol- 音量を下げてメニューを左に
CH+ プログラム/チャンネルアップとメニューアップ
CH- プログラム/チャンネルダウンとメニューダウン
メニュー メニュー/ OSDを表示します
ソース 入力ソースメニューを表示します
STANDBY 待機電力のオン/オフ

* –ボタン付きテレビ用

テレビコントロールスティック*

テレビのコントロールスティックは、テレビの背面の左下隅にあります。
リモコンの代わりに使用して、テレビのほとんどの機能を制御できます。

テレビがスタンバイモードのとき:

  • コントロールスティックを短く押す – 電源オン

テレビを見ながら:

  • 右/左 – 音量を上げる/下げる
  • UP/DOWN – チャンネルを上下に変更します
  • 短押し – メニューを表示
  • 長押し – スタンバイ電源オフ

メニュー内:

  • 右/左/上/下 – 画面上のメニューでのカーソルの移動
  • 短押し– OK /選択したアイテムを確認
  • 長押し–前のメニューに戻る
    * – コントロールスティック付きテレビ用

モード入力/ソースの選択

異なる入力/接続を切り替えるため。

a) リモコンのボタンを使用する:

  1. [SOURCE /を押します ] –ソースメニューが表示されます。
  2. [▲]または[▼]を押して、必要な入力を選択します。
  3. [OK]を押します。

b1) テレビのボタン*を使用する:

  1. [ソース]を押します。
  2. CH + / CH-ボタンを使用して、必要な入力/ソースまで上下にスクロールします。
  3. [VOL +]を押して、入力/ソースを選択したものに変更します。

b2) テレビコントロールスティック*を使用する:

  1. コントロールスティックを短く押してメニューに入ります。
  2. コントロールスティックを押し下げ、カーソルを[ソース]メニューに移動します。
  3. コントロールスティックを短く押して、ソースメニューに入ります。
  4. コントロールスティックを使用して、必要な入力/ソースを選択します。
  5. コントロールスティックを短く押すと、入力/ソースが選択したものに変わります。
    * – オプション

TVメニューナビゲーション

(▲/▼/◄/►)ボタンを使用して、目的のアイテムに焦点を合わせます。
[OK]ボタンを押して、現在フォーカスされているアイテムを選択します。
戻るボタンを押すと、メニューのXNUMXつ前のステップに戻ります。
EXITボタンを押してメニューを終了します。
HOMEボタンを押してTVホームメニューに入ります。
ライブTVメニューに入るには、TVボタンを押してからMENUボタンを押します。

電子取扱説明書

テレビから直接、より役立つ情報を見つけてください。
オンラインマニュアルを起動するには、HOMEボタンを押し、ホームメニューからアプリを選択し、アプリリストから「E-instructionManual」を選択します。
注記: この電子マニュアルを使用するには、インターネット接続が必要です。

リモコン

テレビのオンスクリーンマニュアルを参照してください

商標

テキスト、ロゴ、会社名

HDMI、HDMI High-Definition Multimedia Interface、および HDMI ロゴという用語は、HDMI Licensing Administrator, Inc. の商標または登録商標です。

ロゴ、会社名

DVB ロゴは、デジタルビデオ放送 (DVB) プロジェクトの登録商標です。

ロゴ、会社名

Dolby Laboratories のライセンスに基づいて製造されています。Dolby、Dolby Audio、およびダブル D 記号は Dolby Laboratories の商標です。

顔の絵

DTS特許については、http://patents.dts.comを参照してください。 DTS LicensingLimitedからのライセンスに基づいて製造されています。 DTS、Symbol、DTSとSymbolを合わせたもの、Virtual:X、およびDTS Virtual:Xのロゴは、米国およびその他の国におけるDTS、Inc。の登録商標および/または商標です。 ©DTS、Inc。無断複写・転載を禁じます。

DTS特許については、http://patents.dts.comを参照してください。 DTS LicensingLimitedからのライセンスに基づいて製造されています。 DTS、Symbol、DTSとSymbolを合わせたもの、DTS-HD、およびDTS-HDロゴは、米国およびその他の国におけるDTS、Inc。の登録商標および/または商標です。 ©DTS、Inc。無断複写・転載を禁じます。

人物の絵

Wi-Fi CERTIFIEDロゴは、Wi-FiAllianceの認証マークです。

顔の絵

顔の絵

人物の絵

Google、Android、YouTube、Android TV およびその他のマークは、Google LLC の商標です。

顔の絵

Bluetooth® ワードマークおよびロゴは、Bluetooth SIG, Inc. が所有する登録商標です。

QRコード

ドキュメント / リソース

PDF thumbnailアンドロイドテレビ
User Guide · Android TV
PDF thumbnailandroid TV
User Guide · android TV, TV

質問と回答

Helpful product questions tied to this manual. Each item links to the full Q&A page.

質問と回答

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. 色を調整して保存するにはどうすればよいですか。
    Wie kann ich die Farbenstellung einstellen u auchspeichern。

    Mönkhoff asks <em><strong>How can I adjust the colors and save them.</strong></em>
    Wie kann ich die Farbenstellung einstellen u auchspeichern。
    Manuals+ clarified question
    質問

    How can I adjust and save the color settings on my Sharp Android TV?

    答え

    To adjust the color settings on your Sharp Android TV, follow these steps using your remote control:

    • を押す ボタンを押してテレビのホームメニューに入ります。
    • 移動 設定 (the gear icon) or press the メニュー button while in Live TV mode.
    • 選択 写真 or 画像設定.
    • Use the arrow buttons (▲/▼/◄/►) to focus on specific color parameters such as , 飽和、 または 色温度.
    • プレス OK to select the item you wish to change and use the arrow buttons to adjust the levels.

    設定の保存: On Sharp Android TVs, picture adjustments are typically saved automatically for the current input source once you exit the menu. To ensure they are applied, simply press the 戻る or EXIT button to leave the settings screen.

    注記: If you are using a specific Picture Mode (like Movie, Game, or Dynamic), the changes you make will usually be saved specifically to that mode. If you wish to reset the colors to factory defaults later, you can find a "Reset to Default" option within the same Picture menu.

  2. tv sharp model 2t-c50ad1x can connect to the internet besides a set-top box If able to connect to the Internet Please tell me how to connect.
    tv sharp รุ่น 2t-c50ad1x สามารถเชื่อมต่ออินเตอร์เน็ตได้มั้ยนอกจากกล่องรับสัญญาณ หากสามารถเชื่อมต่ออินเตอร์เน็ตได้ รบกวนขอวิธีเชื่อมต่อด้วยค่ะ

    ประภาศิริ ศิริกุล asks <em>tv sharp model 2t-c50ad1x can connect to the internet besides a set-top box If able to connect to the Internet Please tell me how to connect.<e/em>
    tv sharp รุ่น 2t-c50ad1x สามารถเชื่อมต่ออินเตอร์เน็ตได้มั้ยนอกจากกล่องรับสัญญาณ หากสามารถเชื่อมต่ออินเตอร์เน็ตได้ รบกวนขอวิธีเชื่อมต่อด้วยค่ะ
    Manuals+ clarified question
    質問

    How do I connect my Sharp Android TV model 2T-C50AD1X to the internet?

    答え

    Yes, your Sharp Android TV model 2T-C50AD1X can connect to the internet. You can connect it using either a wired Ethernet cable or a wireless Wi-Fi connection.

    According to the Quick Start Guide for Sharp Android TVs, here are the methods to connect to the internet:

    有線接続(イーサネット)

    This is a stable and simple way to connect if your TV is near your internet router.

    1. Connect a Cat 5/Ethernet cable (not included) from the Ethernet port on the back of your TV to your broadband modem or router. The port is usually labeled as LAN or with the symbol ⟨⟩.
    2. The TV should automatically detect the connection.

    ワイヤレス接続(Wi-Fi)

    Your TV is Wi-Fi certified, allowing you to connect to your home wireless network.

    • During Initial Setup: When you first turn on the TV, the 'First Time Installation' menu will guide you through the setup process, which includes connecting to a Wi-Fi network. You will need to select your network name (SSID) and enter your password.
    • Connecting After Setup: If you need to connect to Wi-Fi after the initial setup, follow these general steps for Android TV:
    1. を押す button on your remote control to go to the Android TV Home screen.
    2. に移動 設定 icon (usually shaped like a gear) and select it.
    3. 選択 ネットワークとインターネット.
    4. Make sure the Wi-Fi toggle is turned on.
    5. 利用可能なネットワークのリストからWi-Fiネットワークを選択します。
    6. Enter your password using the on-screen keyboard and select the option to connect.

    Once connected, you can access online services, apps, and the electronic instruction manual on your TV.

  3. Television Shar Android. After the power outage, the TV made a loud noise, roar and scream. I restarted it from the mains. After restarting, it started working except that the general arena had disappeared from the presets and the text PROTECTED MODE appeared in the lower left corner of the screen. how to act?
    Televisioni Shar Android. Virtakatkoksen jälkeen tv piti kovaa ääntä, mörinää ja huutoa. irroitin verkkovirrasta.Uudelleen käynnistettyä alkoi toimia paitsi että yle areena oli kadonnut ennakkovalinnoista ja kuvaruudun vasempaan alakulmaan tuli teksti SUOJATTU TILA. miten toimia?

    Matti Juurikkala asks <em>Television Shar Android. After the power outage, the TV made a loud noise, roar and scream. I restarted it from the mains. After restarting, it started working except that the general arena had disappeared from the presets and the text PROTECTED MODE appeared in the lower left corner of the screen. how to act?<e/em>
    Televisioni Shar Android. Virtakatkoksen jälkeen tv piti kovaa ääntä, mörinää ja huutoa. irroitin verkkovirrasta.Uudelleen käynnistettyä alkoi toimia paitsi että yle areena oli kadonnut ennakkovalinnoista ja kuvaruudun vasempaan alakulmaan tuli teksti SUOJATTU TILA. miten toimia?
    Manuals+ clarified question
    質問

    How do I fix my Sharp Android TV showing 'PROTECTED MODE' and missing apps after a power outage?

    答え

    Based on your description, your Sharp Android TV has likely entered a software state similar to 'Safe Mode' or a hardware protection state due to the power surge. While the manual does not explicitly define a 'Protected Mode' text overlay, it provides steps for recovery after electrical disturbances.

    • Perform a Power Reset: Although you have already restarted it, try a 'cold boot.' Unplug the TV from the mains socket, wait at least 60 seconds to allow all internal capacitors to discharge, and then plug it back in.
    • Check for Electrostatic Discharge (ESD) Recovery: The manual notes that in cases of electrostatic discharge or incorrect function, you should switch the TV off and back on using the スタンバイボタン on the remote or the TVコントロールスティック (located on the lower left corner of the back side) to resume normal operation.
    • Restore Missing Apps: If the Yle Areena app is missing from your presets, press the ボタンをクリックして、次の場所に移動します アプリ, and look for it in the full app list. You may need to re-add it to your favorites or re-download it from the Google Play Store if the system data was corrupted during the outage.
    • 工場出荷時設定へのリセット: If the 'Protected Mode' text persists, you may need to perform a factory reset. Go to 設定 > デバイス設定 > リセット. Note that this will erase all your settings and presets.

    If the loud 'roar and scream' noise returns or the 'Protected Mode' message does not disappear after a factory reset, the power outage may have caused hardware damage to the internal power board or mainboard. In this case, you should contact Sharp's authorized service agent as the manual warns that there are no user-serviceable parts inside.

  4. is it possible to connect an external hard drive to record programs?
    è possibile collegare un hard disk esterno per registrare programmi?

    giuseppe asks <em>is it possible to connect an external hard drive to record programs?<e/em>
    è possibile collegare un hard disk esterno per registrare programmi?
    Manuals+ clarified question
    質問

    Is it possible to connect an external hard drive to record programs on a Sharp Android TV?

    答え

    Based on the provided manual for Sharp Android TVs, the recording functionality (PVR) depends on your specific region and model. Here are the key details regarding recording to an external drive:

    • 地域の可用性: The manual explicitly states that the PVR (Personal Video Recorder) function is not available in Italy, Germany, Austria, or Switzerland.
    • USB Requirements: If you are in a supported region, the TV supports playback from USB storage drives, but they must be formatted to FAT16またはFAT32 file systems. The manual notes that NTFS is not supported for media playback, which typically extends to recording functions as well.
    • 繋がり: You can connect an external device via the USB ports located on the back or side of the TV.

    If you are located in Italy (as suggested by the Italian translation in your comment), this feature is disabled on the TV software due to regional restrictions.

  5. Dear Sir or Madam, I have purchased the “Android TV 43BL2EA” device. Have cable connection, after installation a code for a network is required. Is such a code required to receive free channels and where can I get such a code? Many thanks for your help. Gerhard Zimmer
    Sehr geehrte Damen und Herren, habe das Gerät “Android TV 43BL2EA” käuflich erworben. Habe Kabelanschluß, nach Installation wird ein Code für ein Netzwerk gefordert. Ist ein solcher Code für den empfang von freien Sendern erforderlich und wo erhalte ich einen solchen Code? Für Ihre Hilfe besten Dank. Gerhard Zimmer

    Gerhard Zimmer asks <em>Dear Sir or Madam, I have purchased the "Android TV 43BL2EA" device. Have cable connection, after installation a code for a network is required. Is such a code required to receive free channels and where can I get such a code? Many thanks for your help. Gerhard Zimmer<e/em>
    Sehr geehrte Damen und Herren, habe das Gerät "Android TV 43BL2EA" käuflich erworben. Habe Kabelanschluß, nach Installation wird ein Code für ein Netzwerk gefordert. Ist ein solcher Code für den empfang von freien Sendern erforderlich und wo erhalte ich einen solchen Code? Für Ihre Hilfe besten Dank. Gerhard Zimmer
    Manuals+ clarified question
    質問

    Is a network code required to receive free channels on the Sharp Android TV 43BL2EA, and where can I find it?

    答え

    Based on the Sharp Android TV user guide, there are two types of "codes" you might be encountering during setup, but neither is strictly required just to receive free-to-air channels:

    • Wi-Fi/Network Password: If the TV is asking for a "network code" immediately after installation, it is likely asking for your home Wi-Fi password to enable Smart features (like YouTube or Netflix). You can find this on your internet router. You can usually skip this step if you only want to watch cable TV.
    • PINコード: During the "First Time Installation," the TV may ask you to set a 4-digit PIN. This is a security code you create yourself for parental controls. If you haven't set one yet, the default is often 0000, 1111、 または 1234.

    To receive free channels via cable:

    1. Ensure your cable is connected to the RF入力 テレビ裏のコンセント。
    2. 実行 初回インストール and select "Cable" as the scan type.
    3. If your cable provider requires a specific "Network ID" or "Frequency" to start the scan, you must obtain these values directly from your cable service provider's webサイトまたはサポート ライン。

    If the TV is asking for a code to unlock specific channels, those may be encrypted (pay-TV) channels that require a CI+ module and a subscription card from your provider.

  6. Despite the update, no favorites list can be created. There is nothing in the Quick Guide/online manual.
    Trotz Update kann keine Favoritenliste angelegt werden. Im Quick Guide/online Handbuch steht gar nichts drin.

    Susanne asks <em>Despite the update, no favorites list can be created. There is nothing in the Quick Guide/online manual.<e/em>
    Trotz Update kann keine Favoritenliste angelegt werden. Im Quick Guide/online Handbuch steht gar nichts drin.
    Manuals+ clarified question
    質問

    How do I create a favorites list on my Sharp Android TV?

    答え

    You are correct, the Quick Start Guide provided does not contain detailed instructions for all of the TV's features, such as creating a favorites list. As mentioned in the guide, the complete user manual is available electronically on your TV.

    While the exact steps can vary slightly between different Sharp Android TV models, the general process for creating a favorites list is as follows:

    1. While watching Live TV, press the OK or リスト button on your remote control to open the channel list.
    2. With the channel list displayed, press the メニュー or オプション button on your remote. This should open a new menu with more channel options.
    3. 次のようなオプションを探します Channel Edit, Edit Favourites、または単に Favourites. Select it.
    4. You should now see a list of all your channels. Navigate to a channel you want to add to your favorites and select it. There is often an on-screen prompt or a specific button on the remote (sometimes a colored button) to press to add the selected channel to the favorites list.
    5. Repeat this step for all the channels you wish to add.
    6. Once you have finished, press the EXIT or 戻る button to save your changes and leave the menu.

    に view your newly created favorites list, you can usually open the channel list again and switch to the "Favorites" tab or group.

    ご注意ください: These are general instructions. For the precise steps for your specific model, please consult the full electronic manual on your TV. You can typically access it by pressing the button, selecting アプリ, and then choosing "E-instruction Manual" リストから。

  7. I can’t stream from my iPhone XR to the tv match but then the tv doesn’t see or recognize iphone
    Non riesco a trasmettere dal mio iPhone XR alla tv si abbinano ma poi la tv non vede o riconosce iphone

    Rita ida asks <em>I can't stream from my iPhone XR to the tv match but then the tv doesn't see or recognize iphone<e/em>
    Non riesco a trasmettere dal mio iPhone XR alla tv si abbinano ma poi la tv non vede o riconosce iphone
    Manuals+ clarified question
    質問

    How can I stream from my iPhone XR to my Sharp Android TV when the TV does not recognize the device?

    答え

    To stream from an iPhone to a Sharp Android TV, you typically use the Chromecastビルトイン feature or a third-party app, as Android TVs do not always support Apple AirPlay natively depending on the specific model year.

    Follow these troubleshooting steps to get your iPhone recognized:

    • ネットワーク接続を確認します。 Ensure both your iPhone XR and your Sharp TV are connected to the 同じWi-Fiネットワーク. If one is on a 5GHz band and the other on 2.4GHz, they may not see each other.
    • Use Google Home App: Since the manual confirms the TV has Chromecastビルトイン、ダウンロード Google ホーム app on your iPhone. This app is often required to properly "see" and set up the connection between an iOS device and an Android TV.
    • ソフトウェアの更新: Ensure your TV software is up to date. Go to Settings > Device Preferences > About > System Update.
    • デバイスを再起動します。 Perform a power cycle on your router, your iPhone, and your TV (unplug the TV from the wall for 60 seconds).
    • アプリの互換性を確認する: Open a Cast-enabled app (like YouTube or Netflix) on your iPhone and look for the キャストアイコン (a rectangle with Wi-Fi waves in the corner). If the icon appears there but not in general screen mirroring, the TV may only support casting from specific apps rather than full screen mirroring.

    If you are trying to mirror your entire screen and it still fails, you may need to install an app from the Google Play Store on the TV such as エアスクリーン or レプリカ to enable AirPlay-like functionality.

  8. How do I connect my Sharp Android to an old analogue component tp boost sound

    Rogelio Contento asks How do I connect my Sharp Android to an old analogue component tp boost sound
    Manuals+ clarified question
    質問

    How do I connect my Sharp Android TV to an old analogue audio component to boost the sound?

    答え

    To connect your Sharp Android TV to an older analogue audio component (such as a Hi-Fi system or amplifier), you have a few options depending on the ports available on your specific model and your audio equipment:

    • ヘッドフォンジャック: Most Sharp Android TVs include a 3.5mm headphone output. You can use a 3.5mm to RCA cable (red and white plugs) to connect the TV's headphone jack to the "AUX" or "Line In" ports on your analogue component.
    • Mini AV / Mini YPbPr Ports: Some models feature a "Mini AV" or "Mini YPbPr" port. While these are primarily for input, older analogue systems often used these RCA-style connections. Check the 外部デバイスの接続 diagram on page 99 of the manual to identify these ports.
    • Digital to Analogue Converter (DAC): If your TV only has a "Digital Optical Audio Out" (as shown on page 99) and your component only has analogue RCA inputs, you will need an external デジタル-アナログオーディオコンバータ. You would connect an optical cable from the TV to the converter, and then RCA cables from the converter to your audio component.

    セットアップに関する重要な注意事項: Once connected, you may need to adjust the TV settings. Go to Settings > Device Preferences > Sound to ensure the audio output is directed to the correct external source. If using the headphone jack, the TV speakers will usually mute automatically.

  9. Sharp 2K EU TV Android dernière mise à jour faite problème bug l’or de changement de chaîne et fonction application très lente en manipulant avec télécommande

    perraud jean François asks Sharp 2K EU TV Android dernière mise à jour faite problème bug l'or de changement de chaîne et fonction application très lente en manipulant avec télécommande
    Manuals+ clarified question
    質問

    How can I troubleshoot channel changing bugs and slow application performance on my Sharp Android TV after a recent update?

    答え

    If your Sharp Android TV is experiencing slow performance or bugs after a recent update, you can try the following troubleshooting steps based on the user guide:

    • 電源サイクル: In cases of incorrect function or software glitches, switch the TV off and then back on. For a deeper reset, unplug the power cable from the electrical outlet, wait a few minutes, and plug it back in.
    • 省エネモード: Note that long-pressing the STANDBY button on the remote control puts the TV into an energy-saving mode. If the TV is waking from this deep sleep, it may initially appear slower as it reloads system processes.
    • 電子マニュアル: You can access more specific troubleshooting directly on your TV. Press the ボタン、選択 アプリを選択し、 E-instruction Manual リストから。
    • Remote Control Check: Ensure the batteries (2x AAA) are fresh, as low power can cause delayed responses that mimic system slowness.
    • USB Media Notice: If you have a USB drive connected, ensure it is formatted to ファット16 or ファット32. Incompatible file systems (like NTFS) can sometimes cause system instability or slow down the interface while the TV attempts to read the drive.

    If the slowness persists specifically in third-party applications, the manual notes that the manufacturer is not responsible for third-party content or service-related issues, and you may need to contact the specific app provider or check for app-specific updates in the Google Play Store.

質問する

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.