MAGICAMENTE Kitchen Set Instructions

MAGICAMENTE Kitchen Set

仕様

• ブランド： MAGICAMENTE
• 推奨年齢: 3+
• 原産国： 中国製
• 材料: Not specified, but includes plastic fasteners and various-sized screws (M4X44mm, M4X36mm, M4X15mm, M3X18mm).
• コンテンツ： Various numbered pieces (1-21) and accessories (25-28) as detailed in the ‘CONTENIDO’ and ‘ACCESORIOS’ sections of the manual.

使用方法

WARNING! Choking hazard – Small parts. Not suitable for children under 3 years.

The tableware is not intended to contact real food; please do not fill or contact real food.

大人による組み立てが必要です。

注1:

Organize your parts.
Make sure you have all the required parts BEFORE starting the assembly!

• Please use a manual screwdriver for assembly, or set your electric screwdriver to the minimum torque to avoid damaging the product. If the minimum torque is not enough to turn the screws, gradually increase the torque as needed.
• Do not fully tighten the screws until all panels are connected.
• To complete the assembly, use a manual screwdriver to fully tighten all screws until they are secure.

注2:

• The plastic fasteners are pre-installed. However, they may shift during transport. Please check whether the fasteners are correctly seated in the holes and adjust them if they are misaligned.
• The correct installation positions are as follows:

部品リスト

組み立て前:

1. 手順を読む: Please read all instructions before assembling. Incorrect assembly could result in a hazard for the child.
2. パーツを並べ替える: Order your pieces. Make sure you have all the required parts BEFORE starting assembly!

組み立てのヒント:

• Minimum Torque: Please use a manual screwdriver for assembly or adjust your electric screwdriver to MINIMUM TORQUE to avoid damaging the product. If the minimum torque is not sufficient to turn the screws, gradually increase the torque as needed.
• Do Not Fully Tighten Initially: すべてのパネルが接続されるまで、ネジを完全に締めないでください。
• 最終締め付け: To complete assembly, use a hand screwdriver to fully tighten all screws until they are snug. DO NOT OVERTIGHTEN! Overtightening will cause the product to crack.
• Plastic Fasteners (Note 2): Plastic fasteners are pre-installed. However, they may shift during transport. Please check if the fasteners are correctly seated in the holes and adjust them if they are misaligned. The correct installation positions are shown in the diagram on  Pay attention to Note 2 in assembly steps B, E, H, I, J, K, L, O.

組み立て手順:

Follow the diagrams and part numbers provided on

1. ステップA: Use parts 1, 20 (x2) and screws 27 (x2).
2. Step B (See Note 2): Use parts 3 and screws 26 (x2).
3. ステップ C: Use parts 2, 6 (x2).
4. ステップD: Use parts 14 and screws 27 (x2).
5. Step E (See Note 2): Use parts 5 and screws 26 (x4).
6. ステップF： Use parts 4, 16, 19 and screws 28 (x2).
7. ステップG： Use parts 7, 11, 12 and screws 26 (x2).
8. Step H (See Note 2): Use parts 8, 9 and screws 25 (x2).
9. Step I (See Note 2): Use parts 13 (x2) and screws 25 (x4).
10. Step J (See Note 2): Use part 9 and screw 25.
11. Step K (See Note 2): Use part 15 and screw 25. 注意！ Before continuing to the next step, slightly loosen the screw on the back to regulate the turning force of the switches.
12. Step L (See Note 2): Use part 10 and screws 25 (x2).
13. Step M: Use parts 17, 18 (x2).
14. Step N: Use screws 26 (x6).
15. Step O (See Note 2): Use screws 26 (x4).
16. Step P: Use part 21.

トラブルシューティング

• Product Damage During Assembly: If you notice cracking or damage, you may be overtightening screws. Loosen slightly and re-tighten gently. Always use minimum torque for power tools.
• Loose Parts/Wobbly Structure: Ensure all screws are fully tightened (but not overtightened) after all panels are connected. Check that plastic fasteners are correctly seated as per Note 2.
• 不足している部品: Refer to the ‘CONTENIDO’ and ‘ACCESORIOS’ sections to verify all parts are present before starting assembly. If parts are missing, contact the manufacturer.
• Difficulty Turning Screws: If using a manual screwdriver, apply firm, steady pressure. If using an electric screwdriver, gradually increase the torque from minimum if the screws are not turning.