FUNPOWER FT366YG Remote Controller

仕様
| モデル | FT366YG |
|---|---|
| 力 | AAA / 1.5V × 2 batteries |
| バッテリーステータスインジケーター | LED indicator shows key-press status and low-battery condition |
| Control modes (O/D Switch) | O: Direct control; D: Control after learning/pairing |
| Regulatory (FCC ID) | FCC ID: 2ABUP-FT366YG |
| Regulatory (IC) | IC: 25540-FT366YG |
Quick Setup & Use
- Install 2 new AAA / 1.5V batteries, ensuring correct alignment.
- 使用 O/D switch: set to O for direct control, or D for control after learning/pairing.
- Pairing: press the 学ぶ button to pair the transmitter with the receiver (then use D モード)。
- Press buttons to control: ファン速度, color temperature switching, ファンオフ、 そして ファンフォワード/リバース (summer/winter modes).
- Light control: use ライトのオン/オフ, and press/hold to adjust light dimming.
操作手順

- ① LED Indicator: Displays status of key presses and battery levels.
- ② Speed of the Fan: Adjusts the rotation speed of the fan.
- ③ Color temperature switching: Alternates between light color settings.
- ④ Fan OFF: Powers down the fan.
- ⑤ Fan Forward/Reverse: Toggles direction of rotation (summer/winter modes).
- ⑥ Light ON/OFF / Light dimming: Controls the light state and holds to adjust brightness.
- ⑦ Learning button: Used to pair the transmitter with the receiver.
- ⑧ O/D Switch:
- O: 直接制御
- D: Control after learning/pairing
- ⑨ BATTERY: Requires AAA / 1.5V x 2 batteries.
パッケージ内容
- 1 × FUNPOWER FT366YG Wireless Remote Controller
- 1 × Battery (If Included)
- ユーザーマニュアル x 1
- If the LED indicator does not light up when a button on the transmitter is pressed, please check the battery installation and alignment.
- If the LED indicator flashes when a key is pressed, it indicates low battery voltage. Please replace both batteries with new ones.
- Please remove the batteries from the transmitter if it will not be used for an extended period of time.
メンテナンスとクリーニング:
- Clean the remote controller surface using a soft, dry cloth.
- Do not allow water or cleaning liquids to enter the internal components.
- Keep the buttons and battery compartment free from dust.
- Remove the battery if the controller will not be used for a long period.
- Store the remote in a dry location away from heat and moisture.
- Avoid dropping or applying excessive pressure to the controller.
FCCの指示:
この製品はテスト済みであり、FCC規則のパート15に準拠したクラスBデジタルデバイスの制限に準拠していることが確認されています。 これらの制限は、住宅設備での有害な干渉に対する合理的な保護を提供するように設計されています。 この製品は、無線周波数エネルギーを生成、使用、および放射する可能性があり、指示に従って設置および使用しない場合、無線通信に有害な干渉を引き起こす可能性があります。
ただし、特定の設置で干渉が発生しないという保証はありません。 製品がラジオやテレビの受信に有害な干渉を引き起こす場合(これは、機器の電源をオフにしてからオンにすることで判断できます)、ユーザーは次のXNUMXつ以上の方法で干渉を修正することをお勧めします。
- 受信アンテナの向きを変えるか、位置を変えてください。
- 製品と受信機の間の距離を広げます。
- 受信機が接続されている回路とは別のコンセントに製品を接続します。
- 販売店または経験豊富なラジオ/テレビ技術者にご相談ください。
このデバイスは、FCC 規則のパート 15 に準拠しています。操作には次の XNUMX つの条件が適用されます。
- このデバイスは有害な干渉を引き起こすことはありません。
- このデバイスは、望ましくない動作を引き起こす可能性のある干渉を含め、受信したあらゆる干渉を受け入れる必要があります。
警告: コンプライアンス責任者によって明示的に承認されていない変更または修正を行うと、ユーザーの製品操作権限が無効になる可能性があります。
IC注意:
RSS-Gen Issue 5 & RSS-Gen numéro 5This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- このデバイスは干渉を引き起こすことはありません。
- このデバイスは、デバイスの望ましくない動作を引き起こす可能性のある干渉を含め、あらゆる干渉を受け入れる必要があります。
コンプライアンス責任者によって明示的に承認されていない変更または修正を行うと、ユーザーの機器の操作権限が無効になる可能性があります。
RF 曝露に関する声明:
機器は、制御されていない環境に対して定められたIC放射線被曝制限に準拠しています。
トラブルシューティング
- LED indicator does not light when pressing a key: Check the battery installation and alignment.
- LED indicator flashes when a key is pressed: バッテリー容量tage is low—replace both batteries with new ones.
- Remote won’t be used for an extended period: 送信機から電池を取り外します。
ドキュメント / リソース
![]() | FT366YG Remote Controller |
参考文献
- ユーザーマニュアルmanual.tools
