OWON SPM6103 DC電源およびマルチメーター ユーザーマニュアル

1. はじめに

The OWON SPM6103 is a versatile 2-in-1 instrument combining a high-resolution DC power supply and a 4 1/2 digit multimeter. It offers an output power of 300W with a voltage range of 0-60V and a current range of 0-10A. Key features include a 2.8-inch LCD, 10mV/1mA power resolution, output voltage and current curve monitoring, and multiple protection mechanisms. The integrated multimeter supports measurements for voltage, current, capacitance, resistance, continuity, and diode testing.

2. 安全情報

Before operating the OWON SPM6103, please read and understand all safety instructions. Failure to follow these instructions may result in electric shock, fire, or damage to the device.

• Ensure the device is connected to a properly grounded AC power outlet.
• 濡れた状態や濡れた状態でデバイスを操作しないでください。amp 条件。
• デバイスを開けないでくださいasing; there are no user-serviceable parts inside except for the fuse. Refer servicing to qualified personnel.
• 正しいボリュームを確認するtagテスト対象デバイスの損傷を防ぐため、回路に接続する前に電圧と電流の設定を確認してください。
• Use only the specified fuse type and rating for replacement.
• Avoid touching live terminals during operation.

3.製品オーバーview

3.1フロントパネル

The front panel features the 2.8-inch LCD display, control buttons, an adjustment knob, output terminals, multimeter input jacks, and a 5V/1A USB host port.

3.2 背面パネル

The rear panel includes the AC power input jack, power button, fuse holder, and a device USB port for PC connectivity.

4. セットアップ

4.1 開梱と検査

Carefully remove the SPM6103 from its packaging. Inspect the device for any signs of physical damage. Retain the packaging for future transport or storage.

4.2電源接続

1. 背面パネルの電源スイッチがオフになっていることを確認します。
2. Connect the provided AC power cord to the AC power input jack on the rear panel (refer to Figure 3).
3. Plug the other end of the power cord into a grounded AC power outlet (100-120V AC).

4.3 テストリードの接続

For power supply output, connect test leads to the red (+) and black (-) output terminals on the front panel. For multimeter measurements, connect probes to the VΩ-Hz, A, and COM input jacks as appropriate for the measurement type.

4.4 初回電源投入

Press the power button on the rear panel to turn on the device. The 2.8-inch LCD will illuminate, displaying the startup sequence and then the default operating screen.

5. 操作手順

5.1電源モード

1. 設定ボリュームtageと現在： Use the 'V' and 'I' buttons to select the voltage or current parameter. Rotate the adjustment knob to change the value. Press the knob to confirm or switch between coarse/fine adjustment.
2. 出力制御： Press the 'On/Off' button to enable or disable the power output. The display will indicate the output status.
3. Curve Monitoring: The device can display output voltage and current curves. Use the 'DISP' button to cycle through display modes until the curve monitoring screen is shown.
4. List Waveform Editing: The SPM6103 supports editing and outputting 10 groups of timing outputs. Press the 'List' button to access this function.
5. Memory Shortcuts: Four groups of memory shortcut parameters are available for quick output settings. Use the 'Memory' button to save or recall these settings.

5.2 マルチメーターモード

The SPM6103 integrates a 4 1/2 digit multimeter with auto-ranging capabilities.

1. スイッチングモード: Press the 'Mode' button to switch between DC power supply and Multimeter modes.
2. 寸法: Connect the multimeter probes to the appropriate input jacks (VΩ-Hz, A, COM). The device supports measuring voltage, current, capacitance, resistance, continuity, and diode (0-2V).

5.3 USB Host Port (5V/1A)

The front panel features a 5V/1A USB host port for charging small electronic devices or powering USB-compatible accessories.

6. メンテナンス

6.1 クリーニング

To clean the device, disconnect it from all power sources and use a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.

6.2 ヒューズの交換

The device is equipped with a user-replaceable fuse located on the rear panel (refer to Figure 3). If the device fails to power on, check the fuse. To replace:

1. 電源コードをACコンセントから抜きます。
2. Use a flat-head screwdriver to open the fuse holder.
3. Remove the old fuse and replace it with a new fuse of the same type and rating (e.g., 10A, 250V).
4. ヒューズホルダーをしっかりと閉じてください。

6.3 冷却ファン

The SPM6103 includes an intelligent temperature-controlled fan for heat dissipation. The fan will activate automatically when the internal temperature rises. Ensure the rear panel's fan vents are not obstructed to allow for proper airflow.

7。 トラブルシューティング

• デバイスの電源が入らない: Check the AC power cord connection and verify the fuse on the rear panel. Replace the fuse if blown.
• No output from power supply: Ensure the 'On/Off' button has been pressed to enable output. Check that voltage and current limits are set appropriately.
• Multimeter readings are inaccurate: Verify probe connections are secure and correctly inserted for the desired measurement type. Ensure the 'Mode' is set to Multimeter.
• 5V USB host port not charging: Some users have reported issues with the 5V USB connection. Ensure the connected device is compatible and try a different USB cable. If the issue persists, contact support.
• PC software display in incorrect language: If using the PC software, locate the language settings within the application. For initial setup, a button in the lower-left corner of the software interface may switch the display to English.
• ファンのノイズ： The intelligent temperature-controlled fan will operate when the device reaches a certain temperature. This is normal. If the fan runs excessively or makes unusual noises, ensure vents are clear.

8. 仕様

9. 保証とサポート

For warranty information, technical support, or service inquiries, please contact OWON customer service or refer to the official OWON webサイト。 保証請求に備えて購入時のレシートを保管しておいてください。