1. はじめに
This manual provides detailed instructions for assembling and operating your ICSTATION Heart Shaped LED Light Soldering Project Kit. Designed for beginners and electronics enthusiasts, this kit offers a practical way to enhance soldering skills while creating a decorative LED light display. Please read all instructions carefully before beginning assembly.
2. 箱の中身
組み立てを開始する前に、以下にリストされているすべてのコンポーネントがキットに含まれていることを確認してください。
Image: All components included in the Heart Shaped LED Light Soldering Project Kit, laid out for inspection.
- Heart-shaped PCB (Printed Circuit Board)
- 32個のRGB LED
- STC89C58RD Microcontroller
- DIP40 IC Socket
- 抵抗器（さまざまな値）
- Capacitors (various values)
- 水晶発振器
- 電源スイッチ
- Battery Holder (for 2x AAA batteries)
- Acrylic Case components (front, back, stand)
- ネジ
- 接続ワイヤ
3. 安全情報
警告： This kit involves soldering, which uses high temperatures and can produce fumes. Always follow these safety guidelines:
- はんだの煙を吸い込まないように、換気のよい場所で作業してください。
- Wear safety glasses to protect your eyes from splashes or flying debris.
- 火傷を防ぐためにはんだごてスタンドを使用してください。
- Ensure the soldering iron is unplugged and cooled down when not in use.
- Keep flammable materials away from your work area.
- はんだを扱った後は手をよく洗ってください。
- 大人の直接監督がない限り、子供の手の届かないところに保管してください。
4. セットアップと組み立て
This section guides you through the assembly process. A soldering iron, solder, and basic tools like wire cutters and needle-nose pliers are required (not included in this kit).
4.1. 準備
- すべてのコンポーネントを開梱し、「箱の中身」リストと照らし合わせて確認します。
- Prepare your soldering workstation with adequate ventilation and lighting.
- Familiarize yourself with the PCB layout and component placement.
4.2. 部品のはんだ付け
Solder components in order from smallest to largest to ensure easier access. Start with resistors, then capacitors, crystal, and finally the IC socket and LEDs.
- 抵抗器: Identify the resistors by their color codes or markings. Insert them into their designated positions (R1-R32) on the PCB. Bend the leads on the underside to hold them in place, then solder and trim excess leads.
- Capacitors and Crystal: Solder the small ceramic capacitors and the crystal oscillator into their respective positions. Ensure the crystal is securely seated.
- Microcontroller Socket: Place the DIP40 IC socket onto the PCB, aligning the notch on the socket with the notch on the PCB silkscreen. Solder all pins. This socket allows for easy insertion/removal of the microcontroller.
- LEDは： Carefully insert each of the 32 RGB LEDs into their designated holes. LEDs are polarized; ensure the longer lead (anode) goes into the hole marked with a '+' or the square pad, and the shorter lead (cathode) goes into the round pad. Solder each LED and trim the leads.
- 電源スイッチ： Solder the power switch into its position.
- Battery Holder Wires: Connect the red wire from the battery holder to the '+' pad and the black wire to the '-' pad on the PCB.
Image: Close-up of the heart-shaped PCB with resistors correctly soldered into place.
4.3. Microcontroller Installation
Gently insert the STC89C58RD microcontroller into the soldered IC socket. Ensure the notch on the microcontroller aligns with the notch on the socket and PCB. Apply even pressure to avoid bending pins.
4.4. Acrylic Case Assembly
- Remove the protective film from all acrylic pieces.
- Attach the stand piece to the bottom of one heart-shaped acrylic cover using the provided screws.
- Carefully place the assembled PCB into the acrylic cover with the stand.
- Align the second acrylic cover on top and secure it with the remaining screws. Ensure the power switch is accessible.
Image: The finished heart-shaped LED light enclosed in its standable acrylic case.
4.5. バッテリーの取り付け
Insert two AAA batteries (not included) into the battery holder, observing correct polarity (+/-). The device is now ready for operation.
Image: Close-up of the battery compartment, showing where to insert two AAA batteries.
4.6. 組み立てビデオガイド
組み立て手順のビジュアルガイドについては、以下の公式製品ビデオを参照してください。
Video: Official product video demonstrating the assembly and features of the Heart Shaped LED Light Soldering Project Kit.
5. 操作手順
Once assembled and batteries are installed, operating the Heart Shaped LED Light is straightforward.
- 電源オン: Locate the power switch on the side or bottom of the acrylic case. Slide the switch to the "ON" position.
- ライトディスプレイ: The 32 RGB LEDs will immediately begin to display a variety of colorful patterns and effects. The microcontroller is pre-programmed with multiple light show sequences.
- 電源を切る： デバイスの電源をオフにするには、電源スイッチを「OFF」の位置にスライドします。
Image: The assembled heart-shaped LED light showcasing its dynamic rainbow LED light show.
6. メンテナンス
- クリーニング： Use a soft, dry cloth to gently wipe the acrylic case. Avoid abrasive cleaners or solvents.
- バッテリー交換: If the LED light show becomes dim or stops working, replace the two AAA batteries. Ensure correct polarity.
- ストレージ： Store the kit in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries to prevent leakage.
- コンポーネントの検査: Periodically check soldered joints for any signs of corrosion or loose connections. Re-solder if necessary.
7。 トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| LEDは点灯しません。 |
|
|
| 一部の LED が点灯しません。 |
|
|
| Light patterns are erratic or incorrect. |
|
|
8. 仕様
| 特徴 | 詳細 |
|---|---|
| モデル番号 | GY21248-2 |
| 寸法（長さ×幅×高さ） | 1.18 x 3.07 x 1.18インチ |
| アイテム重量 | 1.76オンス |
| LEDタイプ | RGB LEDs (32 count) |
| 電源 | 2 x AAA電池（別売） |
| マイクロコントローラ | STC89C58RD |
Image: Diagram showing the dimensions of the assembled Heart Shaped LED Light.
9. 保証とサポート
Specific warranty information for this product is not provided in the available data. For any technical support, missing parts, or inquiries regarding your ICSTATION Heart Shaped LED Light Soldering Project Kit, please contact the manufacturer or seller directly through the platform where the product was purchased.
Manufacturer: ICSTATION
