導入
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Tridonic Linear Essence Series 43 Watts Constant Current LED Driver. This driver is designed for high-performance constant current output and 0-10V dimming control, making it suitable for energy-efficient commercial lighting systems in the U.S. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
安全情報
WARNING: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all applicable national and local electrical codes.
- 設置または保守の前に電源を切ってください。
- 電気的危険を防ぐために適切な接地を確保してください。
- 指定された入力ボリュームを超えないようにしてくださいtage or output power ratings.
- This device is designed for dry and damp locations only. Do not expose to water or excessive moisture.
- 過熱を防ぐために、運転者の周囲に十分な換気を確保してください。
- The driver is equipped with overload, short-circuit, no-load, and overtemperature protection. However, proper installation is crucial for safe operation.
パッケージ内容
インストールを開始する前に、すべてのコンポーネントが揃っていることを確認してください。
- 1 x Tridonic Linear Essence Series 43W Constant Current LED Driver (Model: TLD-CC43W-UNV-LE2)
セットアップとインストール
Follow these steps for proper installation of your Tridonic LED Driver. Ensure power is disconnected before proceeding.
1. Mounting the Driver
Mount the LED driver securely in a suitable enclosure or fixture. Ensure the mounting surface is stable and can support the weight of the driver. Allow for adequate space around the driver for air circulation to prevent overheating.
Figure 1: Tridonic Linear Essence Series 43W LED Driver. This image shows the overall design of the driver, highlighting its compact form factor and the terminal blocks for electrical connections.
2. 配線接続
Refer to the wiring diagram on the driver label and the instructions below for correct electrical connections. Use appropriate wire gauges for all connections.
図2：詳細 view of the Tridonic LED driver's wiring terminals. This image provides a close-up of the input (AC Line, Neutral, Ground) and output (LED positive/negative, 0-10V dimming control) connections, which are clearly labeled on the driver's casing.
- 入力電源 (AC): Connect the AC line (L), neutral (N), and ground (G) wires from your power source to the corresponding terminals on the driver. The driver supports a rated supply voltag120-277 V AC。
- LED Output (DC): Connect the LED positive (LED+) and LED negative (LED-) wires from your LED module to the corresponding output terminals on the driver. Ensure correct polarity.
- 0-10V調光制御: Connect the 0-10V dimming control wires (0-10V+ and 0-10V-) from your dimming system to the dedicated dimming terminals. This allows for dimming from 10% to 100%.
- 接地: Ensure the driver casing is properly grounded.
3. Output Current Adjustment (DIP Switches)
The driver features adjustable output current settings (915mA or 1,000mA) via DIP switches. Refer to the driver's label for the specific DIP switch configuration to select your desired output current. Adjust these settings before applying power.
インストールビデオガイド
For a visual guide on wiring and installation, please refer to the official Tridonic Switch Series LED Drivers video below. This video demonstrates the connection process for similar Tridonic drivers, providing helpful visual cues for proper wiring.
Video: Tridonic Switch Series LED Drivers. This video illustrates the wiring process for Tridonic LED drivers, including connecting input power, LED output, and dimming control wires. It provides a practical demonstration of the steps involved in setting up the driver.
操作手順
Once installed and wired correctly, the Tridonic LED driver operates automatically. The primary control is through the 0-10V dimming interface.
- 電源オン/オフ: The LED driver will power on when AC input voltageが提供されます。
- 調光： Use a compatible 0-10V dimmer connected to the dimming terminals to adjust the light output from 10% to 100%. A 0V signal typically corresponds to the minimum dimming level (10%), and a 10V signal corresponds to 100% light output.
メンテナンス
The Tridonic LED driver is designed for long-term, maintenance-free operation. However, periodic checks can help ensure continued performance.
- クリーニング： Ensure the driver's exterior is free from dust and debris to maintain proper heat dissipation. Clean with a dry, soft cloth. Do not use liquid cleaners.
- 接続: Periodically inspect all wiring connections to ensure they remain secure. Loose connections can lead to intermittent operation or electrical hazards.
- 環境： Verify that the operating environment remains within the specified temperature and humidity ranges (Dry and Damp Location, IP20).
トラブルシューティング
If you encounter issues with your LED driver, refer to the following common problems and solutions:
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| LEDが点灯しない | No input power; Incorrect wiring; Faulty LED module; Driver protection activated. | Check power supply; Verify all wiring connections (L, N, G, LED+, LED-); Test LED module; Cycle power to reset driver protection. |
| LEDs flickering or unstable dimming | Loose connections; Incompatible dimmer; Dimming wires incorrectly connected. | Check all wiring connections; Ensure 0-10V dimmer is compatible; Verify 0-10V+ and 0-10V- connections. |
| Driver is hot to the touch | 換気が不十分、過負荷。 | Ensure adequate airflow around the driver; Verify total LED load does not exceed 43W. |
| Dimming range not 10-100% | Dimmer incompatibility; Dimmer settings. | Confirm dimmer is fully compatible with 0-10V standard; Check dimmer's minimum/maximum settings. |
仕様
| 特徴 | 詳細 |
|---|---|
| モデル番号 | 87501064 (LC 43/915–1000/50 0-10V fixC lp SNC2 UNV) |
| タイプ | 定電流 LED ドライバー |
| 出力電力 | 43W（最大） |
| 定格供給量tage | 120〜277 V AC |
| ACVol。tage範囲 | 108〜305 V AC |
| 電源周波数 | 50/60Hz |
| 最大出力巻tage (U-OUT) | 60V DC |
| 調光インターフェース | 0-10V |
| 調光範囲 | 10～100% |
| 調整可能な出力電流 | 915 mA or 1,000 mA (via DIP switches) |
| IP 定格 | IP20 |
| ハウジング材質 | Metal, White |
| 保護機能 | Overload, Short-circuit, No-load, Overtemperature |
| 公称寿命 | 最大50,000時間 |
| 製品寸法（長さ x 幅 x 高さ） | 11.00" x 1.10" x 0.90" in. |
| 製品重量 | 7.0オンス |
| 認定資格 | UL Listed Class P, Meets DesignLights Consortium 4.3 |
保証
The Tridonic Linear Essence Series LED Driver is backed by a 5年間保証 from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service conditions. Please retain your proof of purchase for warranty claims. The warranty does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.
サポート
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Tridonic customer support or your authorized dealer. Provide your product model number (87501064) and a detailed description of the issue when seeking support.
You can also visit the official Tridonic web追加のリソースと連絡先情報のサイト。
