オイチョー100 Amp MPPTソーラー充電コントローラー 12V/24V ユーザーマニュアル

1. はじめに

Thank you for choosing the OOYCYOO 100 Amp MPPT Solar Charge Controller. This device is designed to efficiently manage power flow from your solar panels to your battery bank, ensuring optimal charging and system protection. It is compatible with 12V and 24V battery systems and supports various battery types including AGM, Sealed, Gel, Flooded, and Lithium batteries.

2. 安全に関する注意事項

• インストールと操作の前に、すべての指示を注意深くお読みください。
• Ensure all wiring is correctly polarized (positive to positive, negative to negative) to prevent damage.
• Always connect the battery to the charge controller first, before connecting solar panels. Disconnect solar panels first, then the battery.
• Use appropriate wire gauges for all connections to handle the rated current.
• 過熱を防ぐため、コントローラーは換気の良い場所に設置してください。
• Avoid short circuits and reverse polarity connections.
• コントローラーをご自身で分解したり修理したりしないでください。修理が必要な場合は、資格のある担当者にご相談ください。

3 製品の特徴

• MPPT (Maximum Power Point Tracking) technology for efficient solar energy harvesting (≥99% tracking rate, >98% conversion rate).
• 自動12V/24Vシステムボリュームtage識別。
• Compatibility with multiple battery types: USER (customizable for Lithium, LiFePO4, Li(NiCoMn)O2), Flooded, Sealed, and Gel batteries.
• User-programmable settings for absorption voltage、フローティングボリュームtage、および低容量tage切断します。
• Comprehensive protection features: PV over current/power, PV short circuit, PV reverse polarity, night reverse charging, battery reverse polarity, battery over voltage, battery over discharge, battery overheating, controller overheating, lithium battery low temperature, load short circuit, load overload, TVS high voltageトランジェント。
• Built-in cooling fan with intelligent temperature control (ON >45℃, OFF <40℃) and porous heat dissipation for extended lifespan.
• Blacklight LCD Display showing charge amount (KWH) and other parameters.
• Max PV input power: 1300W (12V system), 2600W (24V system).
• 最大PV開放回路電圧tage：100VDC。

4. パッケージ内容

• 1 x OOYCYOO 100A MPPT Solar Charge Controller
• 温度センサー x 1
• ユーザーマニュアル（英語）1冊

5. 仕様

6. セットアップとインストール

6.1. 開封と終了view

Upon unboxing, inspect the charge controller for any visible damage. Familiarize yourself with the device's layout and connection points.

6.2. 取り付け

Mount the charge controller vertically on a non-flammable surface in a dry, well-ventilated area, away from direct sunlight and heat sources. Ensure sufficient clearance around the unit for proper airflow, especially around the cooling fans.

6.3. 配線接続

Follow the wiring sequence carefully to avoid damage to the controller or batteries. The controller accepts up to 6 AWG wire for main power connections. Ensure all connections are tight and secure.

1. バッテリー接続: Connect the battery cables to the BATTERY terminals on the controller first. Ensure correct polarity (positive to positive, negative to negative).
2. ソーラーパネル接続: Connect the solar panel cables to the SOLAR PANEL terminals. Ensure correct polarity.
3. 負荷接続（オプション）: If using the DC load output, connect your DC loads to the DC LOAD terminals. Ensure correct polarity.
4. 温度センサー: Plug the included temperature sensor into the designated port. Attach the sensor to the battery for accurate temperature compensation during charging.

For a visual guide on setting up a solar system with a charge controller and inverter, refer to the video below:

6.4. 初期設定

After all connections are made, the controller will power on. You may need to configure the battery type and system voltage if it's not automatically detected or if you are using a custom battery type like Lithium.

The controller features a blacklight LCD display for easy monitoring and configuration. Use the buttons to navigate through the menu and adjust settings as needed. For detailed instructions on setting battery parameters, refer to the specific section in the printed user manual.

7. 操作手順

The LCD display provides real-time information about your solar system. Use the navigation buttons (Menu, Up, Down, Enter) to view different parameters and access settings.

7.1. LCDディスプレイオーバーview

The display shows various parameters such as:

• PVVol。tageと現在
• バッテリー巻tageと充電電流
• ロードボリュームtageと現在
• バッテリー容量のパーセントtage
• 周囲温度
• Cumulative Power Generation (KWH)
• Error/Fault Indicators

7.2. Setting Battery Parameters

To optimize charging for your specific battery type, you can adjust parameters like absorption voltage、float voltage、および低容量tage disconnect. Consult the detailed instructions in the full user manual for precise steps on how to enter the settings menu and modify these values.

7.3. 負荷制御

The controller features a programmable load timer. You can set the load to turn on/off at specific times or based on battery voltage levels. This feature helps conserve battery power and manage your DC loads efficiently.

8. メンテナンス

• すべての配線接続部の締め付け具合と腐食を定期的に点検してください。
• Keep the controller's cooling vents clear of dust and debris to ensure proper heat dissipation.
• Periodically inspect the battery terminals for corrosion and clean if necessary.
• LCD ディスプレイにエラー コードや異常な表示がないか監視します。

9。 トラブルシューティング

If you encounter issues with your OOYCYOO MPPT Solar Charge Controller, refer to the following general troubleshooting tips:

• ディスプレイなし/電源なし: バッテリーの接続を確認し、バッテリーの容量を確認してくださいtageは最小動作電圧を超えているtage.
• 充電なし: Verify solar panel connections and ensure sufficient sunlight. Check for any PV over current/short circuit protection activation.
• バッテリーの過放電: 低音量を調整するtage disconnect setting if necessary. Ensure your loads are not exceeding the battery's capacity.
• エラーコード: Consult the full user manual for a list of specific error codes and their corresponding solutions.

For issues related to battery activation or if your battery is not working as expected, the following video provides helpful steps:

10.保証とサポート

For warranty information, technical support, or service inquiries, please refer to the contact details provided in your product packaging or visit the OOYCYOO official webサイトでご確認ください。購入証明として購入レシートを保管してください。