1. はじめに
This manual provides essential information for the safe and efficient installation, operation, and maintenance of the POTTER PSN-106B 10 AMP 6 NAC Power Supply. Please read this manual thoroughly before attempting to install or operate the unit. Retain this manual for future reference.
Figure 1: POTTER PSN-106B 10 AMP 6 NAC Power Supply. This image shows the front view of the power supply, highlighting its black casing and the layout of its connection terminals and status indicators.
2. 安全情報
警告： Installation and servicing must be performed by qualified personnel only. Disconnect all power sources before servicing to prevent electric shock or equipment damage.
- 必ず地域および国の電気規則に従ってください。
- ユニットが適切に接地されていることを確認してください。
- ユニットを湿気や極端な温度にさらさないでください。
- 入力ボリュームを確認するtag電源に接続する前に、電圧と電流定格を確認してください。
3.製品オーバーview
The POTTER PSN-106B is a 10 AMP, 6 NAC (Notification Appliance Circuit) power supply designed for fire alarm and security applications. It provides regulated and filtered power to connected devices.
主な特徴:
- 10 Amp total output current.
- Six independently supervised Notification Appliance Circuits (NACs).
- Built-in battery charger for standby power.
- Fault monitoring and reporting capabilities.
4. セットアップとインストール
4.1 ユニットの取り付け
- Select a suitable location that is clean, dry, and free from excessive vibration or heat.
- Mount the power supply securely to a wall or other stable surface using appropriate fasteners. Ensure adequate ventilation around the unit.
4.2配線接続
Refer to the wiring diagram provided inside the unit's enclosure for specific connection points. All wiring must comply with NFPA 70 (National Electrical Code) and NFPA 72 (National Fire Alarm and Signaling Code).
- AC電源入力： Connect the main AC power source to the designated terminals. Ensure the power source matches the unit's voltag要件。
- バッテリー接続： Connect standby batteries to the battery terminals, observing correct polarity. Batteries are essential for maintaining power during AC failures.
- NAC Outputs: Connect notification appliances (horns, strobes, etc.) to the NAC terminals. Each NAC is supervised for open and short circuits.
- 補助出力: Connect auxiliary devices requiring regulated power to the auxiliary power terminals.
- Trouble/Supervisory Relays: Connect these outputs to the main fire alarm control panel (FACP) for remote fault reporting.
5. 操作手順
5.1 初期電源投入
- After all wiring is complete and verified, apply AC power to the unit.
- Observe the status indicators. The AC POWER LED should illuminate steadily.
- If batteries are connected, the BATTERY CHARGE LED should indicate charging status.
5.2 ステータスインジケータ
| インジケータ | 状態 | 説明 |
|---|---|---|
| 交流電力 | 緑（安定） | AC power is present and within normal operating range. |
| バッテリー | 緑（安定） | Batteries are connected and fully charged. |
| バッテリー | 黄色（点滅） | バッテリーは充電中です。 |
| トラブル | 黄色（点灯） | A fault condition exists (e.g., AC failure, battery fault, ground fault, NAC fault). |
| NAC 1-6 | 緑（安定） | NAC is active and supplying power. |
| NAC 1-6 | 黄色（点灯） | NAC fault detected (open or short circuit). |
6. メンテナンス
Regular maintenance ensures the reliable operation of your PSN-106B power supply. All maintenance should be performed by qualified personnel.
- 毎月: Inspect the unit for any visible damage. Verify all status indicators are normal.
- 毎年： テストバッテリーvoltage and capacity. Replace batteries as recommended by the manufacturer (typically every 3-5 years). Clean any dust accumulation from the enclosure and ventilation openings.
- 記録の保存: Maintain a log of all inspections, tests, and maintenance performed.
7。 トラブルシューティング
If the unit exhibits abnormal behavior, refer to the following table before contacting technical support.
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| AC POWER LED Off | AC入力電源がありません。 | Check circuit breaker, power cord, and AC input terminals. |
| TROUBLE LED On | General fault condition. | Check other status LEDs for specific fault (e.g., battery, ground, NAC). |
| BATTERY LED Yellow (Steady) | Battery fault or low battery. | Check battery connections, voltage, and age. Replace if necessary. |
| NAC LED Yellow (Steady) | NAC open or short circuit. | Inspect wiring on the affected NAC for breaks or shorts. Verify end-of-line resistor. |
8. 仕様
| パラメータ | 価値 |
|---|---|
| モデル | PSN-106B |
| ブランド | ポッター |
| 出力電流 | 10 Amps（合計） |
| NAC | 6 |
| ワットtage | 100ワット |
| 欧州連合 | 742779300829 |
| ASIN | B09LFLLWWD |
| 初回利用可能日 | 9年2021月XNUMX日 |
9. 保証と技術サポート
For warranty information, please refer to the documentation included with your purchase or visit the official POTTER website. For technical assistance, contact POTTER customer support. Ensure you have your model number (PSN-106B) and purchase details available when contacting support.
メーカー: ポッター
Web: www.pottersignal.com （元amp（リンクは変更される場合があります）
