WOLFBOX T10 Plus/T10 Mirror Dash Cam Hardwire Kit Instruction Manual

1.製品オーバーview

The WOLFBOX Hardwire Kit is designed to provide continuous power to your WOLFBOX T10 Plus/T10 Mirror Dash Cam, enabling 24/7 parking surveillance and eliminating the need for a cigarette lighter adapter. This kit is compatible with vehicles operating on 12V to 24V systems.

• 幅広い互換性: Connects directly to your vehicle's power system, supporting 12V to 24V input, suitable for cars, trucks, buses, and SUVs.
• 24時間7日駐車監視: Provides constant power to your dash cam, allowing it to monitor your vehicle even when the engine is off, protecting against theft and incidents in parking lots.
• 点火制御電力: Can be wired to an ignition-switched fuse for power that turns on and off with your vehicle, ensuring automatic operation without manual intervention.
• Mini USB Plug: Compatible with all Mini USB dash cams, GPS navigators, and radar detectors, freeing up your vehicle's cigarette lighter port.
• 低ボリュームtag保護: Features a smart system that automatically cuts power to the dash cam if your vehicle's battery voltage drops below 11.6V (for 12V systems) or 22.8V (for 24V systems), preventing battery drain.

Figure 1: Internal Cable Structure of the Hardwire Kit

2. セットアップとインストール

2.1 安全上の注意

Before beginning the installation, ensure the vehicle's engine is off. Disconnect the negative terminal of the vehicle's battery to prevent short circuits or electrical damage during installation.

2.2 コンポーネント以上view

The hardwire kit includes the main power cable with a Mini USB connector, a voltage converter box, and various fuse tap sizes to match your vehicle's fuse box.

Figure 2: Included Fuse Tap Sizes

2.3 配線接続図

Refer to the diagram below for a visual guide on connecting the hardwire kit to your vehicle's fuse box.

図3: ハードワイヤーキットの配線図

2.4 ステップバイステップのインストール

1. ダッシュカムに接続: Plug the Mini USB end of the hardwire kit into your WOLFBOX dash cam.
2. ヒューズボックスの位置: Identify your vehicle's fuse box. This is typically located under the dashboard, in the glove compartment, or in the engine bay. Consult your vehicle's owner's manual if needed.
3. Connect Constant Power (Yellow Cable): The yellow cable (BATT) provides constant power. Locate a fuse in your vehicle's fuse box that is always live, even when the ignition is off. Use an appropriate fuse tap from the kit to connect the yellow cable to this fuse slot. Ensure you insert the original fuse and a new fuse (if provided) into the fuse tap.
4. Connect Ignition-Switched Power (Red Cable): The red cable (ACC) provides power only when the ignition is on. Locate a fuse in your vehicle's fuse box that receives power only when the ignition is turned on. Use an appropriate fuse tap to connect the red cable to this fuse slot.
5. Connect Ground (Black Cable): The black cable (GND) is for grounding. Connect this cable to a metal part of the vehicle's chassis or a bolt that is securely fastened to the vehicle's metal frame. This provides a stable ground connection.
6. ケーブルの配線: Carefully route all cables to conceal them and prevent interference with driving. Use cable clips or ties to secure them.
7. バッテリーを再接続します: すべての接続が確実に行われたら、車両のバッテリーのマイナス端子を再度接続します。
8. テストシステム： Start your vehicle and check if the dash cam powers on. Turn off the ignition and observe if the parking surveillance mode activates (if applicable to your dash cam model).

Figure 4: Hardwire Kit Installation Steps

3. 操作

Once installed, the WOLFBOX Hardwire Kit operates automatically based on your wiring configuration and dash cam settings.

3.1 駐車監視

When the vehicle's ignition is turned off, the hardwire kit continues to supply power to the dash cam from the constant power connection (yellow cable). This enables your dash cam's parking surveillance features, such as motion detection or time-lapse recording, to function continuously.

3.2低巻tag保護

ハードワイヤーキットには低電圧が装備されていますtage protection system. If your vehicle's battery voltage drops to 11.6V (for 12V systems) or 22.8V (for 24V systems), the kit will automatically cut power to the dash cam. This prevents excessive discharge of your vehicle's battery, ensuring you can start your engine. Power will resume once the battery voltag安全なレベルに戻ります。

4. メンテナンス

The WOLFBOX Hardwire Kit requires minimal maintenance. Periodically check the connections to ensure they remain secure and free from corrosion. Ensure cables are not pinched or exposed to excessive heat or moisture. If you notice any issues with power supply to your dash cam, inspect the fuse connections and the ground point.

5。 トラブルシューティング

• ダッシュカムの電源が入らない:
  • Verify all connections (Mini USB, ACC, BATT, GND) are secure.
  • Check the fuses in the fuse taps. Replace any blown fuses.
  • 車両のバッテリー容量を確認するtageは低ボラティリティを上回っているtage protection threshold (11.6V for 12V, 22.8V for 24V).
• 駐車監視が機能しない:
  • Confirm the yellow (BATT) cable is connected to a constant power fuse that is always live.
  • Check your dash cam's settings to ensure parking surveillance mode is enabled.
• Incorrect Fuse Tap Size:
  • The kit includes multiple fuse tap sizes. Ensure you are using the correct size for your vehicle's fuse box.
  • If your vehicle requires a fuse type not included, you may need to purchase an additional compatible fuse tap separately.
• Dash Cam Turns Off Unexpectedly:
  • This may be due to the low voltage protection activating. Check your vehicle's battery voltage. If it's low, the kit will cut power to protect the battery.

6. 仕様

7.保証とサポート

WOLFBOX is committed to providing high-quality products and customer satisfaction.

• 保証： この製品には12か月の保証が付いています。
• 返品規則： A 7-day return policy is applicable.
• 欠陥: 欠陥がある場合は返品をお受けいたします。

For technical assistance, warranty claims, or any product-related inquiries, please contact WOLFBOX customer support:

• メールアドレス: service@wolfbox.com
• 電話： +1 888 296 8399

Figure 5: WOLFBOX Warranty and Service Information