LEDVANCE 360DEG Wall Sensor Instruction Manual

1. はじめに

Thank you for choosing the LEDVANCE 360DEG Wall Sensor. This device is designed to provide efficient and automated lighting control for outdoor environments, enhancing both convenience and energy savings. This manual provides essential information for the safe installation, operation, and maintenance of your sensor.

2. 安全情報

設置および操作の前に、これらの安全に関する注意事項をよくお読みください。これらの指示に従わないと、感電、火災、その他の危険が発生する可能性があります。

• 専門家による設置: Installation must be carried out by a qualified electrician in accordance with all local and national electrical codes.
• 電源切断: デバイスの設置、保守、または清掃を行う前に、必ず回路ブレーカーで電源を切ってください。
• 巻tage: 供給量を確認するtage matches the device's requirements (230 Volt AC).
• 環境条件: The device has an IP55 protection rating, making it suitable for outdoor use and protected against dust and low-pressure water jets. However, avoid direct exposure to extreme weather conditions beyond its specified operating range (-20°C to +40°C).
• 修正： Do not modify or alter the device in any way. Unauthorized modifications may void the warranty and create safety hazards.

3. パッケージ内容

インストールを開始する前に、すべてのコンポーネントが揃っていることを確認してください。

• 1x LEDVANCE 360DEG Wall Sensor device

4 製品の特徴

• Stand-alone motion and light sensor for wall mounting.
• 360° detection field for comprehensive coverage.
• Optimized for energy saving.
• Three selectable operating modes: continuous light on, activation by motion, or activation by twilight.
• Zero-crossing circuit optimized for the operation of LED luminaires.
• IP55 protection type, suitable for outdoor use.
• Designed to be disassembled for separate control of internal light sources (if applicable).

5. セットアップとインストール

The LEDVANCE 360DEG Wall Sensor is designed for wall mounting. Refer to the following diagrams and instructions for proper installation.

図5.1: Dimensions of the LEDVANCE 360DEG Wall Sensor. The sensor measures 7.6 cm in width, 9.5 cm in depth, and 11.1 cm in height.

図5.2: 閉じる view of the LEDVANCE 360DEG Wall Sensor unit, showing its black polycarbonate housing and the spherical detection lens at the bottom.

5.1取り付け位置

• Choose a wall location that provides the desired detection coverage. The sensor has a 360° detection field and a maximum detection distance of 10 meters.
• Avoid mounting near heat sources, air conditioning vents, or areas with direct sunlight, as these can interfere with sensor performance.
• Ensure the mounting surface is stable and can support the device's weight (250 grams).

5.2 電気接続

• 警告： 電気接続を行う前に電源を切ってください。
• Connect the sensor to a 230 Volt AC power supply.
• Follow the wiring diagram provided with the product packaging for correct connections. Ensure all connections are secure and insulated.
• The zero-crossing circuit is optimized for LED luminaires.

6. 操作手順

The LEDVANCE 360DEG Wall Sensor offers flexible operation modes and adjustable settings.

6.1動作モード

The sensor features three selectable operating modes:

1. Continuous Light On: The connected light remains continuously on, bypassing sensor detection.
2. Activation by Motion: The connected light turns on when motion is detected within the 360° field.
3. Activation by Twilight: The connected light turns on when ambient light levels fall below a set threshold (twilight) and motion is detected.

Refer to the product's internal settings or external switches (if present) to select the desired mode. Note that some settings may require opening the device, which should only be done by a qualified professional.

6.2 検出設定

The sensor allows for adjustment of the light duration after detection:

• 点灯時間： The duration for which the light remains on after motion detection can typically be set between 2 seconds and 15 minutes. Adjust this setting according to your preference and energy-saving goals.

7. メンテナンス

The LEDVANCE 360DEG Wall Sensor requires minimal maintenance.

• クリーニング： Periodically clean the sensor lens and housing with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the polycarbonate material.
• 検査： Regularly inspect the device for any signs of damage or wear. If any damage is found, disconnect power and contact a qualified electrician for repair or replacement.

8。 トラブルシューティング

If you experience issues with your LEDVANCE 360DEG Wall Sensor, refer to the following common problems and solutions:

• ライトが点灯しない:
  • 電源が接続され、アクティブになっているかどうかを確認します。
  • Verify the operating mode is set correctly (e.g., 'Activation by Motion' or 'Activation by Twilight').
  • 検出エリアに障害物がないことを確認してください。
  • Adjust the sensitivity settings if available.
• ライトが点灯し続けます:
  • Check if the operating mode is set to 'Continuous Light On'.
  • Ensure no constant motion is occurring within the detection zone.
• ライトが突然点灯する:
  • Check for environmental factors like moving branches, small animals, or sudden temperature changes that might trigger the sensor.
  • Adjust the sensor's sensitivity or detection range if possible.

これらの解決策を試しても問題が解決しない場合は、カスタマー サポートまたは資格のある電気技師に連絡してください。

9. 仕様

10. 保証とサポート

The LEDVANCE 360DEG Wall Sensor comes with a 3年間のメーカー保証 購入日から、通常使用における材料および製造上の欠陥をカバーします。

For technical support, warranty claims, or further assistance, please visit the official LEDVANCE store or contact their customer service department. You can find more information and contact details on the LEDVANCEブランドストア.

保証のために購入証明書を保管してください。