1. はじめに
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Aeotec Recessed Door Sensor 7 (ZW187-A). This device is a Z-Wave Plus V2 enabled smart sensor designed to discreetly monitor the open/closed status of doors and windows within your smart home system. It integrates advanced Z-Wave 700 series technology for enhanced range, security, and battery efficiency.
2.製品オーバーview
The Aeotec Recessed Door Sensor 7 is an invisible security solution, designed to be installed within the door or window frame. It consists of two main components: the sensor unit and a magnetic contact. When the magnet moves away from the sensor, it detects an "open" state, and when it returns, it detects a "closed" state. This information is then transmitted wirelessly to your Z-Wave hub.
- Z-Wave Plus V2 (700 Series): Utilizes the latest Z-Wave technology for improved range, faster communication, and lower power consumption.
- SmartStart Enabled: Simplifies the pairing process with compatible Z-Wave hubs by scanning a QR code.
- S2セキュリティ： Provides advanced encryption for secure communication within your Z-Wave network.
- 凹型デザイン: Installs discreetly within door or window frames, maintaining aesthetic appeal.
- 長いバッテリー寿命: Optimized for extended battery performance, typically 2+ years with standard usage.
Image: The Aeotec Recessed Door Sensor 7, showcasing its invisible installation within a door frame.
Image: A close-up of the Z-Wave 700 Series chip, highlighting the advanced technology within the sensor.
3. パッケージ内容
パッケージにすべてのコンポーネントが含まれていることを確認してください。
- 1x Aeotec Recessed Door Sensor 7 (ZW187-A) main unit
- 1x Magnetic contact
- 1x CR2 battery (pre-installed or included separately)
- Mounting screws (if applicable)
Image: The product packaging displaying the main sensor unit, magnetic component, and associated branding.
4. セットアップとインストール
4.1. バッテリーの取り付け
- センサーcを慎重に開けるasing.
- Insert the CR2 battery, ensuring correct polarity. If a plastic pull tab is present, remove it.
- センサーcを閉じるasin安全に。
Note: The device uses a CR2 battery, not a CR123A as sometimes mistakenly listed.
4.2. Pairing with a Z-Wave Hub (Inclusion)
The Recessed Door Sensor 7 supports SmartStart for easy pairing and traditional Z-Wave inclusion.
SmartStart Inclusion (Recommended)
SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the sensor or its packaging with a controller providing SmartStart inclusion. No further action is required, and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
- Z-Wave ハブが SmartStart をサポートしていることを確認します。
- Open your Z-Wave hub's mobile application and select the option to add a new device using SmartStart or by scanning a QR code.
- Scan the QR code located on the sensor unit or its packaging.
- Power on the sensor (ensure battery is installed). The sensor will automatically attempt to pair with the hub.
Image: A smartphone scanning the SmartStart QR code on the sensor for simplified pairing.
Manual Inclusion (Traditional Pairing)
- Place your Z-Wave hub into inclusion/pairing mode (refer to your hub's manual for specific instructions).
- With the sensor powered on, press the action button on the sensor unit once. The LED indicator may flash to confirm inclusion mode.
- If successful, your hub will confirm the device has been added.
- If pairing fails, ensure the sensor is within range of the hub and repeat the process. You may need to exclude the device first if it was previously paired or attempted to pair unsuccessfully.
4.3. 物理的な設置
The Recessed Door Sensor 7 is designed for discreet installation within the door or window frame.
- 場所を選択してください： Identify a suitable location on the top edge of your door or window frame where both the sensor and magnet can be recessed. The magnet should be installed in the moving part (door/window) and the sensor in the stationary frame, or vice-versa.
- ドリル穴: Using an appropriate drill bit (typically 19mm or 3/4 inch), drill two holes approximately 1 inch deep for the sensor and magnet. Ensure the holes are aligned and close enough for the sensor to detect the magnet when the door/window is closed (typically within 1/2 inch).
- コンポーネントを挿入: Gently push the sensor unit and the magnetic contact into their respective drilled holes. Ensure they are flush with the surface.
- テスト： Open and close the door/window to verify that your Z-Wave hub registers the open/closed status correctly. Adjust placement if necessary.
画像: 元ample of the sensor and magnet discreetly installed within a door frame.
5. 操作
Once successfully installed and paired, the Aeotec Recessed Door Sensor 7 operates automatically:
- Open/Closed Detection: The sensor detects when the magnetic contact moves away from or towards the main sensor unit.
- ステータス レポート: Upon detecting a change in state (open or closed), the sensor immediately sends a Z-Wave command to your connected hub, updating its status.
- オートメーション： This status can be used by your Z-Wave hub to trigger various automations, such as turning on lights when a door opens, sending notifications, or activating security routines.
- Battery Reporting: The sensor periodically reports its battery level to the Z-Wave hub.
Image: Illustrates the benefit of monitoring doors and windows for family safety and security.
6. 互換性
The Aeotec Recessed Door Sensor 7 is a Z-Wave Plus V2 device and is compatible with a wide range of Z-Wave certified hubs and gateways. A Z-Wave hub is required for this sensor to function as part of a smart home system.
Known compatible hubs include, but are not limited to:
- サムスンスマートシングス
- フビタット標高
- Fibaro Home Centre 3
- ホームシーア HS3
- ヴェラ
- ドモティツ
- Open Z-Wave
- ISY994i
- Google Assistant (via compatible hub)
- Amazon Alexa (via compatible hub)
Image: Visual representation of various smart home platforms and voice assistants compatible with the sensor.
Image: Depicts a Z-Wave USB stick and a Z-Wave hub, indicating that a smart hub is necessary for the sensor's functionality.
7. メンテナンス
7.1. バッテリーの交換
The sensor is designed for long battery life (typically 2+ years). When the battery level is low, your Z-Wave hub should report this status. To replace the battery:
- Carefully remove the sensor unit from its recessed position.
- cを開くasing.
- 古い CR2 電池を取り外します。
- 正しい極性を確認して、新しい CR2 電池を挿入します。
- cを閉じますasing and re-insert the sensor into its position.
- Verify the battery status updates on your Z-Wave hub.
Note: Some users have reported issues with battery life or reporting. Ensure your Z-Wave hub's firmware and device handlers are up-to-date for optimal performance.
Image: A visual emphasizing the sensor's instant wake-up feature and long battery life.
8。 トラブルシューティング
If you encounter issues with your Aeotec Recessed Door Sensor 7, consider the following:
| 問題 | 考えられる原因 / 解決策 |
|---|---|
| Sensor not pairing (inclusion failure) |
|
| Sensor not reporting open/closed status |
|
| Poor wireless range |
|
| Inaccurate battery reporting or short battery life |
|
9. 仕様
| モデル番号 | ZW187-A |
| Z-Wave周波数 | 908.42 MHz (US/CA/MX) |
| 電源 | CR1電池2個（付属） |
| 動作温度 | 0°C ～ 40°C (32°F ～ 104°F) |
| 動作湿度 | 8%から80% |
| ワイヤレス範囲 | 最大120メートル（394フィート）の見通し距離 |
| 寸法（センサーユニット） | Approximately 3.39 x 3.19 x 1.26 inches (Package Dimensions) - Specific sensor dimensions not provided, refer to installation guide for drilling size. |
| アイテム重量 | 1.76オンス |
| 認定資格 | Z-Wave Plus V2, S2 Security, SmartStart |
10. 保証とサポート
Aeotec products are designed for reliability and performance. For specific warranty information, please refer to the warranty card included with your product or visit the official Aeotec webサイト。
For technical support, troubleshooting assistance, or to access the latest documentation and firmware updates, please visit the official Aeotec support portal:
You can also find additional resources and community forums on the Aeotec webサイト： aeotec.com
