1.製品オーバーview
The Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge (Model 69ELF114TWG) is designed to reduce incoming water pressure to a safe and consistent level for residential and commercial plumbing systems. This unit features a compact design, lead-free bronze construction, and an integrated internal bypass mechanism. It includes a color-coded gauge for easy pressure monitoring and adjustment.
Figure 1: Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge. This image shows the regulator with its integrated pressure gauge and yellow adjustment handle.
2. 安全情報
- 設置やメンテナンスを始める前に、必ず主給水を停止してください。
- 安全メガネや手袋などの適切な個人用保護具 (PPE) を着用してください。
- 漏れを防ぐために、すべての接続が適切に密閉されていることを確認してください。
- Consult local plumbing codes and regulations for proper installation procedures.
- 設置に関して不明な点がある場合は、資格のある配管工に相談してください。
3. パッケージ内容
インストールを開始する前に、すべてのコンポーネントが揃っていることを確認してください。
- 1x Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator
- 1x Integrated Pressure Gauge
4. インストール
This regulator features a double union PEX-A (cold expansion) barb design for simplified installation in PEX-A piping systems. Ensure the regulator is installed in the correct flow direction, indicated by an arrow on the body.
- 設置場所を準備します。 Turn off the main water supply. Drain the water lines to relieve pressure. Select a suitable location for the regulator, typically after the main shut-off valve and before any branch lines.
- Cut and Prepare PEX-A Piping: Cut the PEX-A pipe to the required length, ensuring clean, square cuts. Prepare the pipe ends for cold expansion connections according to PEX-A system manufacturer guidelines.
- Connect the Regulator:
- Apply appropriate thread sealant (e.g., Teflon tape or pipe dope) to the male threads of the PEX-A fittings.
- Thread the PEX-A fittings onto the double union ends of the regulator. Ensure the flow arrow on the regulator body points in the direction of water flow into the building.
- Tighten the union nuts securely, but do not overtighten.
- Perform cold expansion connections on the PEX-A pipe ends to the fittings according to PEX-A system manufacturer instructions.
- 圧力計の取り付け: The pressure gauge is typically pre-installed. Ensure it is securely threaded into the designated port on the regulator body.
- 給水復旧と水漏れの確認: Slowly turn on the main water supply. Carefully inspect all connections for any signs of leaks. Tighten connections as necessary.
図2：側面 view of the Apollo Water Pressure Regulator, showing the double union PEX-A connections and the flow direction arrow. Note the "MAX INLET 400 PSI" marking.
5. 操作手順
The regulator is factory-set at 50 psi and is adjustable from 15 psi to 75 psi. No special tools are required for adjustment.
- 現在の圧力を確認する: Observe the reading on the integrated pressure gauge. The gauge is color-coded to indicate pressure ranges (e.g., Low, Optimal, Excessive).
- 圧力の調整:
- に 増加 pressure: Turn the yellow adjustment handle 時計回り.
- に 減少 pressure: Turn the yellow adjustment handle 反時計回り.
- Make small adjustments and allow the system pressure to stabilize before re-checking the gauge.
- 設定を確認: Once the desired pressure is achieved (typically between 50-60 psi for most residential applications), confirm the reading on the gauge.
図 3: 拡大図 view of the Apollo Water Pressure Regulator, highlighting the pressure gauge with its color-coded optimal range and the yellow adjustment handle.
6. メンテナンス
The Apollo Water Pressure Regulator is designed for minimal maintenance. Regular checks can help ensure optimal performance.
- Periodic Pressure Check: Periodically check the pressure gauge to ensure the system pressure remains at the desired setting. Fluctuations may indicate a need for adjustment or inspection.
- 漏れ検査: Annually inspect the regulator and connections for any signs of leaks or corrosion.
- クリーニング： レギュレータの外側を洗浄するamp 必要に応じて布で拭いてください。刺激の強い化学薬品は使用しないでください。
- Sediment Filter (Optional): If your water supply contains significant sediment, consider installing a sediment filter upstream of the pressure regulator to prevent internal clogging.
7。 トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| No water flow or very low pressure downstream | Regulator set too low; Main water supply off; Regulator clogged. | Increase pressure setting; Check main water valve; Inspect for debris (consult a plumber if necessary). |
| Pressure too high downstream | Regulator set too high; Regulator malfunction. | Decrease pressure setting; If problem persists, regulator may need replacement. |
| Water hammer or fluctuating pressure | Rapid changes in water demand; Regulator bypass mechanism issue. | Ensure proper air chambers are installed in the plumbing system; Consult a plumber for regulator inspection. |
| 接続部の漏れ | Improperly tightened connections; Insufficient thread sealant. | Tighten connections; Reapply thread sealant if necessary (ensure water supply is off first). |
8. 仕様
- モデル： 69ELF114TWG
- 材料： ブロンズ
- インレット接続サイズ： 3/4インチ
- 入口接続タイプ: Cross Linked Polyethylene (PEX-A)
- コンセント接続タイプ: ペックス
- 最大動作圧力: 400 PSI (Inlet)
- 調整可能な圧力範囲: 15 - 75 PSI (Factory-set at 50 PSI)
- 商品の寸法 (長さ x 幅 x 高さ): 2.13 x 7 x 8インチ
- 商品の重量: 2.53ポンド
- 認定: Certified to ASSE 1003 and CSA B356, listed by ASSE and IAPMO (cUPC)
- 特別な機能: Integrated internal bypass mechanism, Color-coded gauge
9. 保証とサポート
This Apollo Water Pressure Regulator comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Apollo customer support.
For technical support or inquiries, please visit the official Apollo webサイトまたは顧客サービス部門に連絡してください。