TESY BiLight 電気温水器 100リットル ユーザーマニュアル

1.製品オーバーview

The TESY BiLight Electric Hot Water Cylinder is an unvented hot water solution designed for energy-efficient hot water supply to multiple points of use. It incorporates Insutech technology to reduce heat loss by 16% compared to similar products, meeting high European Energy Efficiency, Quality, and Safety standards.

主な機能は次のとおりです。

• Offers Low Cost, Energy Efficient Hot Water
• Patented Piston Effect to control refilling
• Glass Ceramic Coating for corrosion resistance and Freeze Protection
• Wall Mounted design, suitable for various settings including homes, businesses, kitchens, hairdressers, and camp サイト
• Light Indicator to show heating status
• Equipped with a Safety Temperature Pressure Valve
• Thermal Load Temperature Safety Cut Out for enhanced safety

図1: 前面 view of the TESY BiLight Electric Hot Water Cylinder, showing the main unit and indicator panel.

2. 安全情報

重要： Installation of unvented hot water cylinders is subject to Building Control Regulations in the UK. It is mandatory to seek advice from and use a qualified installer for the installation of this product. Failure to comply with regulations can lead to serious hazards and may void your warranty.

UK building regulations require two forms of safety to be installed. This hot water cylinder is fitted with a temperature safety cut-off switch. Additionally, it is strongly recommended to install a safety expansion vessel and a pressure release valve within the connecting plumbing system to ensure full compliance and safe operation.

• メンテナンスやインストールを行う前に必ず電源を切ってください。
• 電気接続の接地が適切であることを確認してください。
• Do not operate the unit if any part is damaged or if there are signs of leakage.
• 可燃物を給湯器から遠ざけてください。
• ユニットの周囲に十分な換気を確保してください。

3. インストール（セットアップ）

Installation must be carried out by a qualified professional in accordance with local building codes and regulations, particularly those pertaining to unvented hot water systems.

3.1. 敷地選定

• Choose a location that can support the weight of the cylinder when full (approximately 126 kg for the 100 Litre model).
• Ensure adequate space for maintenance and access to connections.
• The unit is designed for wall mounting.
• ユニットを凍結温度から保護してください。

3.2. ユニットの取り付け

1. Securely attach the wall mounting brackets to a structurally sound wall using appropriate fasteners.
2. Carefully lift and hang the cylinder onto the installed brackets. Ensure it is level and stable.

3.3. 配管接続

• Connect the cold water supply to the inlet (typically marked blue). The unit has 15mm water connections.
• Connect the hot water outlet (typically marked red) to your hot water distribution system.
• Install a safety expansion vessel and pressure release valve as required by regulations and manufacturer recommendations.
• すべての接続が防水であることを確認してください。

3.4。 電気接続

• Connect the unit to a dedicated 220 Volts electrical supply circuit.
• Ensure the circuit is protected by an appropriate circuit breaker and RCD (Residual Current Device).
• All electrical work must comply with local electrical codes and be performed by a qualified electrician.

図2：詳細 views of the TESY BiLight water heater, showing the bottom connections, temperature control dial, and wall mounting bracket.

4. 操作

Once installed and filled with water, the TESY BiLight water heater is designed for straightforward operation.

4.1. 初期起動

1. Ensure the cylinder is completely filled with water before switching on the power. Open a hot water tap to allow air to escape until water flows steadily.
2. Switch on the electrical power supply to the unit.
3. The light indicator on the unit will illuminate, indicating that the heating element is active and water is being heated.

4.2. 温度制御

The unit features a temperature control dial, typically located at the bottom or side of the unit (refer to Figure 2). Rotate the dial to adjust the desired water temperature. Higher settings will provide hotter water, but also consume more energy. The unit has a built-in overheat protection system.

4.3.通常の操作

The water heater will automatically maintain the set temperature. The light indicator will turn off once the desired temperature is reached and will illuminate again when the heating element reactivates to reheat the water.

5. メンテナンス

Regular maintenance ensures the longevity and efficient operation of your TESY BiLight water heater. All maintenance should be performed by a qualified technician.

• 年次検査: It is recommended to have the unit inspected annually by a qualified professional. This includes checking the pressure relief valve, expansion vessel, and electrical connections.
• 陽極ロッドチェック: The glass-lined tank is protected by an anode rod. This rod should be inspected and replaced periodically (typically every 1-3 years, depending on water quality) to prevent corrosion.
• タンクの排水: If the unit will be out of use for an extended period or if there is a risk of freezing, the tank should be drained. Consult a professional for proper draining procedures.
• クリーニング： ユニットの外側を清潔に保ちますamp 布で拭いてください。研磨剤や溶剤は使用しないでください。

6。 トラブルシューティング

Before attempting any troubleshooting, ensure the power supply to the unit is disconnected. For complex issues, contact a qualified technician.

7. 仕様

Technical specifications for the TESY BiLight Electric Hot Water Cylinder 100 Litre model:

8. 保証とサポート

For warranty information and technical support, please refer to the documentation provided with your purchase or contact TESY customer service directly. Keep your proof of purchase for warranty claims.

For further assistance, you may also contact the seller, The Modern Group, through the Amazon platform.