Xprinter Q200 80mmサーマルPOSレシートプリンター ユーザーマニュアル

1. はじめに

The Xprinter Q200 is an 80mm thermal Point-of-Sale (POS) receipt printer designed for commercial applications. It features high-speed printing, an integrated autocutter, and versatile connectivity options including USB and LAN (Ethernet). This manual provides detailed instructions for setting up, operating, maintaining, and troubleshooting your Xprinter Q200 printer.

2. 安全情報

• プリンターが正しい電圧のアース付き電源コンセントに接続されていることを確認してください。tage.
• プリンターを水や過度の湿気にさらさないでください。
• プリンターを直射日光の当たる場所や熱源の近くに置かないでください。
• Use only the specified power adapter provided with the printer.
• 内部コンポーネントの損傷を防ぐため、プリンターをほこりやごみから遠ざけてください。
• プリンターをご自身で開けたり修理したりしないでください。資格のあるサービス担当者にご相談ください。
• Handle thermal paper carefully; avoid touching the thermal print head immediately after printing as it may be hot.

3. パッケージ内容

Please check the package contents upon unpacking. If any items are missing or damaged, contact your vendor.

• Xprinter Q200 Thermal Receipt Printer
• 電源アダプター
• 電源ケーブル
• USBデータケーブル
• Thermal Paper Roll (for initial testing)
• ユーザーマニュアル（このドキュメント）

4.製品オーバーview

4.1 プリンタコンポーネント

図1: Xprinter Q200 Thermal POS Receipt Printer, showing the overall design with the Xprinter logo and power switch on the front.

図2: フロント view of the Xprinter Q200, highlighting the power switch and the Xprinter branding.

図3: トップ view of the Xprinter Q200 with the paper cover open, revealing the thermal paper compartment and the print head mechanism.

4.2 背面パネルと接続

図4: 後方 view of the Xprinter Q200, displaying the various connectivity ports and the DIP switch configuration table.

The rear panel of the Xprinter Q200 provides the following connection ports:

• シリアルポート（DB9）： シリアル通信用。
• USB Port (Type-B): コンピューターに直接接続します。
• LANポート（RJ45）： ネットワーク接続用。
• Cash Drawer Port (RJ11): キャッシュドロワーを接続します。
• 電源入力: 電源アダプタを接続します。

4.3 DIPスイッチの設定

The DIP switches on the rear panel allow for configuration of various printer functions. Refer to the table below for settings:

注記： Ensure the printer is powered off before changing DIP switch settings.

5. セットアップ

5.1 電源の接続

1. 電源ケーブルを電源アダプタに接続します。
2. Plug the power adapter's output connector into the power input port on the rear of the printer.
3. 電源ケーブルを適切な電源コンセントに差し込みます。

5.2 Connecting Data Cable

次の接続方法のいずれかを選択します。

• USB接続: Connect one end of the USB cable to the USB Type-B port on the printer and the other end to an available USB port on your computer.
• LAN（イーサネット）接続: Connect an Ethernet cable to the LAN port on the printer and the other end to your network router or switch.
• シリアル接続: Connect a serial cable to the DB9 serial port on the printer and the other end to the serial port on your computer.

5.3 感熱紙のセット

1. Press the cover open button (usually located on the side or front of the printer) to open the top cover.
2. Insert the 80mm thermal paper roll into the paper compartment with the printing surface facing upwards.
3. Pull a small amount of paper out past the cutter blade.
4. 上部カバーをカチッと音がするまでしっかりと閉じます。

5.4 ドライバのインストール

For USB or Serial connections, a printer driver is typically required. For LAN connections, the printer can often be configured via its IP address. Refer to the driver CD (if included) or the manufacturer's website for the latest drivers and installation instructions compatible with your operating system.

6. 操作手順

6.1 電源のオン/オフ

• To power on the printer, press the power switch located on the front panel to the 'ON' position. The power indicator light will illuminate.
• To power off the printer, press the power switch to the 'OFF' position.

6.2 表示灯

The printer typically features indicator lights (e.g., Power, Error, Paper) to show its status:

• パワーライト： プリンタの電源がオンになっていることを示します。
• エラーライト: Illuminates or flashes to indicate an error condition (e.g., print head overheat, cutter error).
• ペーパーライト: ロール紙が少なくなったり、なくなったときに点灯します。

6.3 印刷

Once the printer is connected and drivers are installed (if necessary), you can send print jobs from your POS software or application. The printer will automatically feed the paper and cut the receipt after printing, thanks to its integrated autocutter.

6.4 セルフテスト印刷

A self-test print can be used to verify the printer's basic functionality and print quality without needing a computer connection. The exact procedure may vary, but typically involves holding down a feed button while powering on the printer.

7. メンテナンス

7.1 ロール紙の交換

When the paper indicator light illuminates or printing becomes faint, it's time to replace the paper roll. Follow the steps in Section 5.3 to load a new 80mm thermal paper roll.

7.2 プリントヘッドのクリーニング

Regular cleaning of the thermal print head helps maintain print quality and extends the printer's lifespan.

1. プリンタの電源をオフにして、電源ケーブルを外します。
2. 上部カバーを開きます。
3. Wait for the print head to cool down if the printer has been recently used.
4. サーマルプリントヘッドを綿棒で軽く拭きます。ampイソプロピルアルコールで消毒しました。
5. カバーを閉じてプリンタの電源を入れる前に、プリントヘッドが完全に乾くまでお待ちください。

8。 トラブルシューティング

If you encounter issues with your Xprinter Q200, refer to the following common problems and solutions:

• 電源なし: Ensure the power cable is securely connected to the printer and the power outlet. Check the power switch position.
• 印刷なし: Verify that the paper roll is loaded correctly and not empty. Check the data cable connection (USB/LAN/Serial). Ensure the printer driver is installed and selected as the default printer on your computer.
• 紙詰まり: Turn off the printer, open the top cover, and carefully remove any jammed paper. Close the cover and restart.
• 印刷品質が悪い: Clean the thermal print head as described in Section 7.2. Ensure you are using high-quality thermal paper. Adjust print density via DIP switch SW-3 if necessary.
• Error Light On/Flashing: Refer to the printer's specific error codes (if available in a separate technical manual) or try powering the printer off and on again. If the issue persists, contact support.

9. 仕様

10. 保証とサポート

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your vendor/reseller. You may also visit the official Xprinter website for further assistance and updated resources.