1. はじめに
The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter is designed to provide wireless control for various applications and devices. This device operates at 315MHz and is compatible with all Seco-Larm 315MHz receivers. It can be used to control functions such as garage doors, gates, home lighting, or alarm panels, offering convenient remote operation. Its compact, slimline design includes a keychain for portability.
画像1.1: The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter. This black, rectangular device features two distinct buttons labeled '1' and '2' on its surface. The brand name 'ENFORCER' is visible below the buttons. A metal keychain ring is attached to the transmitter, enhancing its portability.
2 製品の特徴
- ワイヤレス制御： Enables remote operation of compatible devices with the push of a button.
- CODEBUMP Technology: Incorporates anti-code grabbing technology for enhanced security.
- 互換性: Fully compatible with all 315MHz Seco-Larm receivers.
- High Security Codes: Offers over 18 quintillion possible codes to prevent unauthorized access.
- 拡張動作範囲: Operates up to 500 feet, depending on installation and environmental factors.
- LED Transmission Indicator: Provides visual confirmation of signal transmission.
- RF Anti-Scan Protection: Further enhances security against scanning attempts.
- スリムラインデザイン: Compact and portable, includes a keychain for easy carrying.
- Two Buttons, Three Channels: Provides control over multiple functions.
3. パッケージ内容
パッケージにすべてのアイテムが揃っていることを確認します。
- Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter with Keychain
- CR2032電池（プリインストールまたは付属）
4. セットアップ
4.1. バッテリーの取り付け/起動
The transmitter comes with a CR2032 battery. In most cases, the battery is pre-installed. If the transmitter does not respond, or if the LED indicator does not light up when a button is pressed, the battery may need to be activated or replaced. Refer to the "Maintenance: Battery Replacement" section for instructions.
4.2. 受信機とのペアリング
To function, the SK-917T2-GNQ transmitter must be paired or "learned" into a compatible 315MHz Seco-Larm receiver. The specific pairing procedure varies depending on the model of your Seco-Larm receiver. Please refer to the instruction manual provided with your Seco-Larm receiver for detailed pairing instructions.
- Ensure your Seco-Larm receiver is powered on and in programming mode (refer to receiver manual).
- Press the desired button(s) on the SK-917T2-GNQ transmitter as instructed by your receiver's manual to transmit the code.
- Confirm successful pairing via the receiver's indicator (e.g., LED flash, audible beep).
5. 操作
Once the transmitter is successfully paired with your Seco-Larm receiver, you can operate your connected devices.
- ボタンの機能: The SK-917T2-GNQ features two buttons, typically labeled '1' and '2'. These buttons can be programmed to control different functions or devices depending on your receiver's capabilities and your programming choices.
- 信号の送信: Press and hold the desired button for approximately one second. The LED indicator on the transmitter will illuminate, confirming that a signal is being transmitted.
- 制御デバイス: The receiver will interpret the transmitted signal and activate the corresponding device or function (e.g., open a garage door, turn on a light, arm/disarm an alarm system).
For specific actions associated with each button, refer to your receiver's programming documentation.
6. メンテナンス
6.1. バッテリーの交換
The transmitter is powered by a single CR2032 lithium coin cell battery. When the LED indicator becomes dim or fails to light up during button presses, it is time to replace the battery.
- 送信機の側面にある小さな切り欠きまたは継ぎ目を見つけます。asing.
- 慎重にcをこじ開けるasing 小さなマイナスドライバーまたは同様の工具を使用します。
- Remove the old CR2032 battery, noting its polarity (+ side up).
- 新しい CR2032 電池をプラス (+) 側を上に向けて挿入します。
- cの2つの半分を揃えるasing を押して、カチッと閉まるまでしっかりと押します。
- Test the transmitter by pressing a button and observing the LED indicator.
注意： Dispose of used batteries according to local regulations. Keep batteries out of reach of children.
7。 トラブルシューティング
- 送信機が応答しません:
- 電池の確認：CR2032電池が正しく装着され、十分に充電されていることを確認してください。必要に応じて交換してください。
- Verify pairing: Confirm that the transmitter is properly paired with your Seco-Larm receiver. Refer to your receiver's manual for pairing instructions.
- Obstructions: Ensure there are no significant physical obstructions between the transmitter and the receiver.
- 動作範囲の縮小:
- Environmental factors: Thick walls, metal structures, or other electronic devices can interfere with RF signals.
- Battery level: A low battery can reduce the effective transmission range. Replace the battery if needed.
- Interference: Other 315MHz devices or strong electromagnetic fields might cause interference.
- LEDインジケーターが点灯しない:
- Battery issue: The battery is likely depleted or incorrectly installed. Replace or re-install the battery.
- Transmitter malfunction: If battery replacement does not resolve the issue, the transmitter may be faulty.
8. 仕様
| 特徴 | 詳細 |
|---|---|
| モデル番号 | SK-917T2-GNQ |
| タイプ | 2 つのボタン、3 つのチャンネル |
| 無線周波数 | 315MHz |
| 動作範囲 | Up to 500 feet (line of sight, environment dependent) |
| コードの数 | Over 18 quintillion |
| 電池のタイプ | CR2032（付属） |
| 寸法 | 1-1 / 4 x 2-3 / 16 x 5/16インチ（31.5 x 55 x 8 mm） |
| 重さ | 0.95オンス |
| 認定資格 | FCC、IC |
9. 保証情報
The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter comes with a 2年間の限定保証 from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, unauthorized modification, or improper installation. Please retain your proof of purchase for warranty claims.
10. サポート
For further assistance, technical support, or warranty inquiries, please contact Seco-Larm customer service. Refer to the official Seco-Larm web最新の連絡先情報については、サイトまたは製品パッケージをご覧ください。
