導入
The TC Electronic FLUORESCENCE SHIMMER REVERB is a shimmering, super-bright reverb pedal designed to create ethereal reverb sounds. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your pedal.
図1：上 view of the FLUORESCENCE SHIMMER REVERB pedal.
- Shimmering Reverb: Creates bright, ethereal reverb effects.
- Intuitive 4-Knob Interface: Simple controls for easy sound shaping.
- トゥルーバイパス: Ensures ultimate signal integrity when the effect is disengaged.
- 耐久性のある構造: Features a robust metal chassis for roadworthy reliability.
設定
Follow these steps to connect your FLUORESCENCE SHIMMER REVERB pedal:
- 電源接続: Connect a 9V DC, 100mA power adapter (center negative) to the power input jack on the pedal. This pedal operates on corded electric power.
- 入力接続: Connect your guitar or other instrument to the 1/4 inch (6.35mm) INPUT jack on the pedal using a standard instrument cable.
- 出力接続: Connect the 1/4 inch (6.35mm) OUTPUT jack of the pedal to your amp信号チェーン内の次のエフェクト ペダルとして使用できます。
- 配置: For optimal shimmer reverb effects, place the FLUORESCENCE SHIMMER REVERB pedal towards the end of your effects chain, typically after modulation and drive pedals, but before delay pedals.
図2：背面 view showing input, output, and power connections.
ペダルの操作
The FLUORESCENCE SHIMMER REVERB pedal features a straightforward 4-knob interface for easy control over your sound:
Figure 3: Control knobs for the FLUORESCENCE SHIMMER REVERB pedal.
- リバーブノブ： Controls the overall decay time and size of the reverb effect. Turning it clockwise increases the length and spaciousness of the reverb.
- MIXノブ: Adjusts the balance between your dry (unaffected) signal and the wet (effected) signal. Turn clockwise for more reverb effect, counter-clockwise for less.
- トーンノブ： Shapes the tonal character of the reverb. This control allows you to brighten or darken the shimmer effect, from warm and subtle to crisp and cutting.
- SHIMMER Knob: This dedicated control adds an octave-up effect to the reverb tail, creating the signature ethereal, shimmering sound. Increase for a more pronounced shimmer.
- フットスイッチ: Engages or disengages the effect. The pedal features true bypass, ensuring your signal remains unaffected when the pedal is off.
メンテナンス
To ensure the longevity and optimal performance of your FLUORESCENCE SHIMMER REVERB pedal, follow these maintenance guidelines:
- クリーニング： ペダルの外装を拭く際は、柔らかく乾いた布をご使用ください。研磨剤入りの洗剤や溶剤は塗装を傷める可能性があるため、使用しないでください。
- ストレージ： ペダルは直射日光や極端な温度を避け、涼しく乾燥した場所に保管してください。
- 接続: すべてのケーブル接続部が摩耗していないか定期的に点検してください。ジャックにほこりやゴミが付着していないことを確認してください。
- 電源： Always use a regulated 9V DC, 100mA (center negative) power supply. Using an incorrect power supply can damage the unit and void the warranty.
- 身体ケア: The pedal features a durable metal chassis. However, avoid dropping the unit or subjecting it to excessive force to prevent internal damage.
トラブルシューティング
If you encounter issues with your FLUORESCENCE SHIMMER REVERB pedal, consult the following common solutions:
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| 音が出ない、または信号が弱い | Incorrect cable connections, faulty cables, no power, pedal disengaged. | Verify all cables are securely connected. Test with different cables. Ensure power supply is connected and functional. Press the footswitch to engage the effect. |
| リバーブ効果なし | MIX knob set too low, REVERB knob set too low, pedal disengaged. | Increase the MIX and REVERB knob settings. Ensure the pedal is engaged. |
| 不要なノイズやハム音 | Faulty power supply, ground loop, interference from other pedals/equipment. | Use a high-quality, isolated power supply. Try connecting the pedal to a different power outlet. Ensure all cables are shielded and in good condition. |
| Shimmer effect is too subtle or too intense | SHIMMER knob setting. | Adjust the SHIMMER knob to achieve the desired intensity. Experiment with the TONE knob to fine-tune the character. |
仕様
- モデル： FLUORESCENCE SHIMMER REVERB
- ASIN: B079Y519PH
- 商品の重量: 1.1 ポンド (0.5 キログラム)
- 製品寸法: 5.2 x 2.91 x 2.28インチ
- 本体材質: 金属
- 色： 青
- コネクタタイプ: 1/4インチ（6.35mm）オーディオジャック
- ハードウェアインターフェイス： 1/4インチオーディオ
- 電源: コード式電気
- 巻tage: 9V DC (100mA, center negative recommended)
- 発売日: 27年2018月XNUMX日
保証とサポート
TC Electronic products are designed and manufactured to high standards. For detailed warranty information and technical support, please refer to the official TC Electronic web公式サイトをご覧いただくか、カスタマーサービスに直接お問い合わせください。保証請求の際に必要となりますので、購入証明書を保管してください。
さらにサポートが必要な場合は、次のサイトを参照してください。 AmazonのTC Electronic Store.