Command Indoor Mini Light Clips (CL806-45NA) Instruction Manual

1.製品オーバーview

The Command Indoor Mini Light Clips (Model CL806-45NA) provide a damage-free solution for hanging lightweight items such as string lights, fairy lights, and small decorations indoors. These clear clips blend with surfaces and are designed for easy application and clean removal without leaving holes, marks, or sticky residue.

Image 1.1: Packaging for Command Indoor Mini Light Clips, illustrating the contents of 45 clear clips and 54 small Command Strips.

パッケージ内容:

• 45 x Clear Mini Light Clips
• 54 x Small Command Strips

2. 安全情報

Please read and follow all instructions carefully to ensure safe and effective use of Command Indoor Mini Light Clips.

• ベッドの上にぶら下がらないでください。
• 壁紙には使用しないでください。
• Do not use for hanging valuable items.
• Ensure the indoor temperature is between 50°F (10°C) and 105°F (40°C) during application.
• Wait seven days after painting before applying clips to allow paint to cure.
• Do not use on textured walls, brick, fabric, or rough surfaces.
• Maximum weight recommendation per clip is 0.3 pounds (approximately 135 grams).

3. セットアップとインストール

Proper surface preparation and application are crucial for optimal adhesion and damage-free removal.

3.1 表面処理

1. Select a clean, smooth surface. Suitable surfaces include painted walls, finished wood, laminate, glass, metal, and tiles.
2. Clean the surface with rubbing alcohol. Wipe gently and let it dry completely. Do not use household cleaners as they may leave residues.

Image 3.1: Illustration of surfaces compatible with Command Clips (painted walls, metal, painted concrete, laminate & finished wood, tile, smooth surfaces & glass) and incompatible surfaces (wallpaper, fabric, textured walls, brick, rough surfaces).

3.2 Clip Application

1. Separate the Command Strip from its liner.
2. Press the black liner side of the strip firmly onto the back of the clip.
3. ストリップから青いライナーを取り外します。
4. Position the clip on the desired clean surface. Press the clip firmly against the wall for 30 seconds.
5. Wait 1 hour before hanging any items on the clip. This allows the adhesive to reach maximum strength.

Image 3.2: A user demonstrating the application of a Command Mini Light Clip to a smooth wooden surface.

ヒント： Use one light clip for every two feet of lights to ensure proper support.

Image 3.3: Visual guide for spacing, recommending one clip for every two feet of lights.

4. 操作手順

Once installed, the Command Indoor Mini Light Clips are ready for use. Simply insert the light cord or small decoration into the clip.

画像4.1: クローズアップ view of a light string secured within a Command Mini Light Clip.

These clips are designed for indoor use only and for lightweight items. Do not exceed the maximum weight capacity of 0.3 pounds per clip.

5. Removal and Maintenance

Command Strips are designed for clean removal without surface damage when instructions are followed.

5.1 Clean Removal

1. Gently slide the clip upwards off the base.
2. Hold the base of the clip gently.
3. Slowly stretch the strip straight down along the wall, keeping your hand against the wall. Stretch at least 6 inches (15 cm) until the base and strip release from the wall.
4. Do not pull the strip towards you or lift it off the surface. Always pull straight down.

Image 5.1: Demonstration of the proper technique for removing a Command Strip, emphasizing stretching downwards for damage-free removal.

5.2 メンテナンス

The clips themselves can be reused with new Command Small Strips. Store unused clips and strips in a cool, dry place.

6。 トラブルシューティング

• Clip not sticking:
  • Ensure the surface was cleaned with rubbing alcohol and allowed to dry completely.
  • Verify the surface is smooth and not textured, wallpapered, or brick.
  • Check that the indoor temperature is within the recommended range (50°F - 105°F).
  • Ensure the strip was pressed firmly for 30 seconds and allowed to set for 1 hour before use.
  • Confirm that the paint on the wall has cured for at least seven days if recently painted.
• Clip falling off:
  • Check if the weight of the item exceeds the 0.3 lb capacity per clip.
  • Review surface preparation and application steps.
  • Ensure the strip was stretched straight down during removal, not pulled outwards.
• Surface damage upon removal:
  • This typically occurs if the strip was not stretched straight down or if used on an unsuitable surface (e.g., wallpaper, textured walls).
  • Always follow the removal instructions carefully.

7. 仕様

8. 保証とサポート

For warranty information or product support, please refer to the official Command brand website or contact 3M customer service. Specific warranty details may vary by region.

オンラインリソース:

• Command How-To Guides
• Command Brand Store on Amazon