BTF-LIGHTING SK6812 RGBW 個別アドレス可能 LED ストリップ ユーザーマニュアル

1. 安全に関する注意事項

本製品を設置または操作する前に、すべての安全に関する指示をよく読んで理解してください。これらの指示に従わない場合、感電、火災、その他の危険が発生する可能性があります。

• 電源のボリュームを確認してくださいtage (DC5V) matches the LED strip requirements. Using an incorrect voltagストリップを損傷する可能性があります。
• Do not connect the LED strip directly to AC power. A DC5V power adapter is required.
• Avoid bending the LED strip sharply, especially at the LED components, as this can damage the circuit.
• Do not immerse non-waterproof (IP30) LED strips in water. IP65 strips are splash-proof, and IP67 strips are suitable for outdoor use but should not be submerged for extended periods.
• 接続やメンテナンスを行う前に、電源を切ってください。
• お子様の手の届かない場所に保管してください。

2.製品オーバーview

The BTF-LIGHTING SK6812 RGBW LED Strip is an individually addressable lighting solution, offering a wide spectrum of colors including a dedicated Natural White channel. Each LED can be controlled independently, allowing for dynamic lighting effects and precise color customization. This model features 144 LEDs per meter and is IP65 waterproof, making it suitable for various indoor and outdoor applications.

Image: Coiled BTF-LIGHTING SK6812 RGBW LED Strip, showing the individual LEDs and flexible PCB.

Image: The LED strip illuminated with a vibrant array of colors, demonstrating its individually addressable capabilities.

3. 特徴

• Individually Addressable RGB+Pure White: Each SK6812 LED integrates RGB and a dedicated Natural White (4000K-5000K) chip, allowing for precise control over color and brightness for each individual LED. This offers richer color combinations and dynamic effects compared to standard RGB strips.
• Enhanced Energy Efficiency: The dedicated pure white LED allows for more energy-efficient white light illumination. Pure White consumes approximately 0.1W/LED, while mixed white (R+G+B) consumes 0.3W/LED.
• Wide Controller Compatibility: Compatible with various programmable controllers such as K-1000C, SP630E, SP639E, SP617E, SP803E, WLED, and SP530E DR04W. These controllers enable diverse lighting effects like chasing, flowing water, and flashing. (Controller and power adapter sold separately).
• Chainable and Cuttable Design: Equipped with 3-pin JST-SM connectors on both ends for easy extension. The strip can be cut at designated points, typically every LED, to customize length.
• 防水等級: Available in different ingress protection (IP) ratings:
  • IP30: Non-waterproof, for indoor use only, with adhesive tape on the back.
  • IP65: Silicone coating waterproof, suitable for indoor use and areas with splashes, with adhesive tape on the back.
  • IP67: Silicone sheathing waterproof, suitable for outdoor use, fixed with screws and clips (no double-sided tape).
• 多用途なアプリケーション: Ideal for LED screens, LED walls, advertising boards, and decorative lighting in hotels, KTVs, bars, and for festive occasions like Christmas or wedding parties.

Image: Detailed diagram illustrating the internal structure of an SK6812 LED, showing RGB and Natural White components, and the flexible PCB design with data direction indicators.

Image: Visual representation of the SK6812 IC, showing where the strip can be cut, and a comparison of IP30, IP65, and IP67 waterproof ratings with their respective thicknesses.

Image: Comparison of LED densities, showing the spacing for 30, 60, and 144 LEDs per meter on the strip.

4. パッケージ内容

パッケージには通常、次の項目が含まれます。

• 1x BTF-LIGHTING SK6812 RGBW LED Strip (1 meter, 144 LEDs/m, White PCB, IP65)
• 1x 3-pin JST-SM male connector
• ユーザーマニュアル（このドキュメント）

Note: Power supply and controller are not included and must be purchased separately.

Image: A coiled LED strip with a 3-pin JST-SM male connector and a female connector with voltage-adding wires, illustrating typical package contents.

5. セットアップ

5.1 電源要件

The LED strip operates on DC5V. For optimal performance and to prevent voltage drop, a DC5V 10A (50W) power supply is recommended for a 1-meter strip with 144 LEDs/m. Ensure your power supply can provide sufficient current for the total length of your LED strip.

5.2コントローラーの接続

Connect the 3-pin JST-SM connector from the LED strip to a compatible individually addressable LED controller. The pins are typically labeled +5V (Power), Din (Data Input), and GND (Ground). Ensure correct polarity and data direction.

5.3 インストール

• IP30/IP65 Strips: These versions come with adhesive tape on the back. Clean the installation surface thoroughly to ensure it is dry and free of dust or grease. Peel off the protective backing and firmly press the strip onto the desired surface.
• IP67 Strips: These strips do not have adhesive tape. Use mounting clips and screws (not included) to secure the strip to the surface. Ensure clips are evenly spaced for stable installation.
• Observe the data direction arrows on the strip to ensure proper signal flow when connecting multiple segments.

6.運用

Operation of the LED strip is dependent on the compatible controller used. Most controllers offer the following functionalities:

• 色の選択: カラーホイールまたは定義済みのカラーオプションを使用して、何百万もの色から選択します。
• 明るさ調整: 光の強さを1%から100%に調整します。
• ダイナミックエフェクト: Select from various pre-programmed lighting modes such as chasing, fading, flashing, and flowing patterns.
• 音楽同期: Some advanced controllers allow the lights to react to music or sound.
• アプリコントロール: Many modern controllers offer smartphone app control for convenient management of lighting effects.

7. メンテナンス

適切なメンテナンスを行うことで、LED ストリップの寿命が長くなり、最適なパフォーマンスが確保されます。

• クリーニング： For IP30 and IP65 strips, gently wipe the surface with a soft, dry cloth. For IP65 and IP67 strips, a damp cloth can be used, but ensure no water enters the connectors or non-waterproof components. Do not use harsh chemicals or abrasive cleaners.
• 検査： Periodically check for any signs of damage, loose connections, or wear and tear. Address any issues promptly to prevent further damage.
• ストレージ： If storing the LED strip, ensure it is clean, dry, and coiled loosely to prevent damage to the circuit or LEDs. Store in a cool, dry place away from direct sunlight.

8。 トラブルシューティング

If you encounter issues with your LED strip, refer to the following common troubleshooting steps:

• 光なし:
  • 電源が正しく接続され、DC5V が供給されているかどうかを確認します。
  • Ensure the controller is powered on and correctly connected to the LED strip (Power, Data, Ground).
  • Verify the data input direction. The signal flows in one direction, indicated by arrows on the strip.
  • Test with a different power supply or controller if available to isolate the issue.
• 色が正しくない、またはちらつく:
  • Confirm that the controller is configured for SK6812 RGBW LEDs. Incorrect IC type selection can cause color issues.
  • Check for loose or damaged data connections.
  • Ensure the power supply is adequate. Voltage drop over long runs can cause color distortion or flickering. Consider injecting power at multiple points for longer strips.
  • Reduce the brightness setting on the controller to see if flickering subsides, indicating a potential power issue.
• Partial Strip Not Lighting:
  • This often indicates a break in the data line or power line at the point where the lights stop. Inspect the strip for physical damage or faulty solder joints.
  • If multiple strips are chained, check the connection between the working and non-working segments.

9. 仕様

10. 保証とサポート

BTF-LIGHTING products are manufactured to high-quality standards. For warranty information, technical support, or any inquiries regarding your product, please refer to the contact information provided with your purchase or visit the official BTF-LIGHTING webサイトでご確認ください。保証請求のために購入証明書を保管してください。

11. 追加リソース

Image: A selection of compatible controllers including Bluetooth, WiFi, and programmable options, suitable for use with SK6812 RGBW LED strips.

画像: Examples of the LED strip installed in different environments, showcasing its versatility in home and commercial lighting applications.