1. はじめに
This manual provides essential information for the safe and efficient operation of your Clover B7A Hot and Cold Water Dispenser. Please read all instructions carefully before installation and use. This high-quality water cooler is designed to provide refreshing chilled drinking water or piping hot water for various uses in your home or office.
画像: 正面 view of the Clover B7A Hot and Cold Water Dispenser with a 5-gallon water bottle installed on top. The dispenser is white with red and blue spigots for hot and cold water, respectively.
2. 安全情報
- ディスペンサーは常に安定した水平な面に設置してください。
- ディスペンサーを直射日光や熱源から遠ざけてください。
- ユニット周囲の適切な換気を確保してください。
- The hot water spigot features a child safety lock. To dispense hot water, you must engage the safety mechanism before pressing the lever.
- Do not plug in the unit until a water bottle is properly installed and water has filled the internal tanks.
- 清掃やメンテナンスを行う前に、ディスペンサーのプラグを抜いてください。
3. セットアップとインストール
- 開梱: ディスペンサーをパッケージから慎重に取り出し、損傷がないか確認してください。
- 配置: Position the dispenser on a flat, sturdy surface near a grounded electrical outlet. Ensure there is adequate space around the unit for ventilation.
- クリーニング： Before first use, wipe down the exterior of the dispenser with a soft, damp cloth. Clean the removable drip tray.
- ウォーターボトルの取り付け:
- Remove the protective seal from a standard 5-gallon water bottle.
- Carefully invert the water bottle and place it firmly onto the bottle support collar at the top of the dispenser. Ensure the bottle is seated correctly and the probe pierces the bottle cap.
- Wait a few minutes for the internal tanks to fill with water. You may hear bubbling sounds as the tanks fill.
- 電源接続: Once the water tanks are filled (bubbling stops), plug the power cord into a grounded 110-120 volt electrical outlet.
- 暖房/冷房を有効にする: Locate the power switches for hot and cold water on the back of the unit. Flip them to the 'ON' position to activate the heating and cooling functions. Allow approximately 15-30 minutes for the water to reach optimal temperatures.
4. 操作手順
- 冷水の供給: Place your cup under the blue spigot. Push the blue lever to dispense chilled water.
- お湯の供給: Place your cup under the red spigot. Engage the child safety lock (usually by sliding a button or pressing a tab) and then push the red lever to dispense hot water. Exercise caution as the water is very hot (approximately 185°F).
- Adjustable Cold Water Thermostat: The cold water temperature can be adjusted between 35.6°F and 53.6°F using the thermostat control located on the back of the unit.
5. 特徴
- Stainless Steel Tanks: Both hot and cold water tanks are constructed of hygienic stainless steel, designed for contaminant resistance and health protection.
- 温度調整: Cold water temperature is adjustable (35.6°F-53.6°F). Hot water temperature is automatically controlled to approximately 185°F (non-adjustable).
- エネルギースター認定: Meets strict energy-efficiency guidelines set by the EPA and U.S. Department of Energy.
- Efficient Heating and Cooling: Features an ultra-efficient condenser cooled via convection, operating quietly.
- Durable Faucets: Equipped with durable polypropylene, self-closing spigots.
- 取り外し可能なドリップ トレイ: One-piece ABS drip tray is removable for easy cleaning.
- Safety Float Mechanism: Double float valve with secondary safety float mechanism helps reduce water loss from spilling.
6. メンテナンスと清掃
- 外装清掃: Regularly wipe the exterior surfaces with a soft, damp 布。 研磨剤入りクリーナーは避けてください。
- ドリップトレイのクリーニング: The removable drip tray should be emptied and cleaned regularly (e.g., weekly or bi-weekly, depending on usage) to prevent water overflow and maintain hygiene. Simply pull it out, empty, wash with mild soap and water, rinse, and snap back into place.
- スケール除去： Over time, mineral deposits may accumulate, especially in the hot water tank, potentially slowing water flow. The manufacturer recommends descaling the unit periodically. Refer to general descaling instructions for water dispensers or coffee makers, using appropriate descaling solutions. Always unplug the unit and drain all water before descaling.
7。 トラブルシューティング
- 温水/冷水なし:
- Check if the hot/cold power switches on the back of the unit are in the 'ON' position.
- ユニットが機能している電源コンセントに接続されていることを確認してください。
- Verify that the water bottle is not empty and is properly seated.
- Allow sufficient time (15-30 minutes) for the water to heat or cool after initial setup or bottle change.
- ゆっくりとした水の流れ:
- Ensure the water bottle is not empty.
- Mineral buildup can restrict water flow, especially for hot water. Refer to the descaling instructions in the Maintenance section.
- 水漏れ:
- Check if the water bottle is properly seated on the dispenser.
- Inspect the water bottle for cracks or damage.
- Ensure the drip tray is correctly installed and not overflowing.
8. 仕様
| 特徴 | 詳細 |
|---|---|
| モデル | B7A |
| 製品タイプ | 温水および冷水ディスペンサー |
| 寸法（長さ×幅×高さ） | 14.00インチ x 12.40インチ x 37.80インチ |
| 重さ | 33.00 ポンド (商品重量: 31.6 ポンド) |
| 色 | 白 |
| 応用 | Dispenses hot and cold water in home or office |
| 巻tage | 110-120ボルト |
| 頻度 | 50～60Hz |
| 認定資格 | CE, NSF, UL |
| タイプ | Bottled (Top-loading) |
| 水温 | ホット＆コールド |
| Hot Water Thermostat Temp. Range | Automatically controlled to nearly 185°F (non-adjustable) |
| Cold Water Thermostat Temp. Range | Adjustable from 35.6-53.6°F |
| 蛇口の種類 | Durable polypropylene, self-closing spigots |
| エネルギースター認定 | はい |
| Drip Tray Type | Removable one-piece ABS drip tray |
| 対応ボトルサイズ | 5ガロン |
| Built-In Filtration System | いいえ |
| 材料 | Polyethylene (PE), Polypropylene (PP), Stainless Steel |
9. 保証とサポート
The Clover B7A Hot and Cold Water Dispenser comes with a 1年間のメーカー限定保証.
For technical support, warranty claims, or further assistance, please contact CLOVER customer service. Refer to the product packaging or the official CLOVER web現在の連絡先情報については、サイトをご覧ください。
