D149H181 Ed.08
AKO-D14918
の AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
警告
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
説明
- LEDCOM
- レコードキー
- EXTERNAL POWER CONNECTOR
- READ KEY
- LEDオン
- CONNECTOR CABLE
互換性
Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 プログラミングキー。
Connecting incompatible devices can permanently damage the key.
配線
- 重要： Pay attention to the orientation of the connector.
- AKO-80018
（オプション） - AKO-D14918
電源
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 または同等のもの）。
手術
重要： After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the コム led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the コム led starts flashing quickly.
When recording is complete the controller will reset.
LEDオン
Steady or flashing: Indicates that the key is connected to the controller.
LEDCOM
安定した： Indicates an error in the transmission/reception of data
高速点滅： Indicates transmission/reception of data in progress. At the end of the transmission LEDCOM 電源が切れます。
ゆっくり点滅: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
注記： To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
重要： 一度もない disconnect the programming key during data transmission.
技術仕様
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
供給量tage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
環境仕様：
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
AKOエレクトロメカニカ
平均ロケテス、30-38 | 08812 サン・ペレ・デ・リベス |バルセロナ |エスパーニャ
35D149181 REV.07 2025
当社は、技術シートに記載されているものと若干異なる可能性のある材料を供給する権利を留保します。
最新情報は、 webサイト。
ドキュメント / リソース
 |
AKO D14918 Programming Key [pdf] 取扱説明書 AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |