1. はじめに
The Pinmany RZ-FT52A is a CAN Bus Data Converter designed to integrate with Android head units in compatible Toyota vehicles. This device facilitates communication between your vehicle's CAN Bus system and an aftermarket Android car radio, enabling features such as steering wheel controls and other vehicle data to function correctly.
2. 安全上の警告と注意事項
- 営業巻tage: The decoder operates within a voltage range of +9V to +16V. Voltages outside this range (too low or too high) can cause permanent damage to the device.
- 配線： The product's sockets are 16-pin and 20-pin connectors with a pin pitch of 2.0mm. Always follow the provided pin definition chart strictly for wiring. Improper wiring can damage the CAN Bus decoder and potentially other vehicle electronics.
- 専門家による取り付けを推奨: Installation requires certain professional knowledge, especially concerning vehicle wiring and Android head unit configuration. If you are unsure about the fitting or wiring process, it is highly recommended to seek professional assistance.
- ケーブルは付属しません: This CAN Bus decoder does not include connection cables. Ensure you have suitable cables or purchase a compatible CAN Bus adapter with cables.
3. 仕様
| 特徴 | 詳細 |
|---|---|
| モデル名 | RZ-FT52A |
| ブランド名 | pinmany |
| メーカー | 上げる |
| 特集 | CAN Bus Data Converter |
| アイテムタイプ | ケーブル、アダプタ、ソケット |
| 営業巻tage | 12 V (Range: +9V~+16V) |
| アイテム重量 | 50グラム |
| 商品サイズ（長さ×幅×高さ） | 73.5mm x 46.5mm x 18.5mm (±1mm error due to manual measurement) |
| 材料 | Black plastic shell |
| インタフェース | 16-pin / 20-pin PH2.0 connectors |
| 起源 | 中国本土 |
| Suitable Head Unit | Android 7"/9"/10"/etc. head units with 8-pin connectors and serial communication. |
| Compatible Car Models (Toyota SEA) |
|
4.インストールガイド
The installation process involves physically connecting the CAN Bus decoder and configuring your Android head unit. Ensure the vehicle's power is off before beginning any wiring.
4.1 物理的な接続
- コネクタを識別します。 Locate the 16-pin and 20-pin CAN plug of your vehicle's wire harness.
- デコーダーを接続: Plug the 16-pin and 20-pin plugs from the wire harness into the corresponding sockets on the CAN Bus Box. Refer to the pin definition diagram for correct orientation and wiring.
- ヘッドユニットの互換性: Ensure your Android head unit has an 8-pin connector for serial communication, as shown in Figure 6.
4.2 Android Head Unit Setup
After physical connection, you need to configure the CAN Bus settings on your Android head unit. The exact steps may vary between different Android head unit models and manufacturers. Consult your head unit vendor's manual if these steps differ.
- 設定を入力してください： From the Android head unit's main screen, navigate to the "Settings" menu. This might be an icon labeled "Car Settings" or similar.
- 工場出荷時設定にアクセス: Within the settings, look for an option like "Factory" or "Factory Settings".
- Enter Factory Password: You may be prompted to enter a factory password. Common passwords include: 3368, 1617, 8317, 8888. If none of these work, contact your Android radio seller for the correct password.
- Navigate to CAN Bus Settings: Once in the factory settings, find the "CAN Bus setting" or "CAN Related Settings" option.
- Select Manufacturer and Model: In the CAN Bus settings, select "Raise" as the CAN Bus manufacturer. Then, choose your specific Toyota car model and year from the list.
- 保存して再起動します: Save the settings and reboot your Android head unit for the changes to take effect.
5. 操作
Once the RZ-FT52A CAN Bus Decoder is correctly installed and configured with your Android head unit, it operates automatically. Its primary function is to translate the vehicle's CAN Bus signals into a format that your Android head unit can understand, enabling the proper functioning of features such as:
- ステアリングホイールコントロール
- Reverse Gear Detection (for camera activation)
- 車速信号
- 照明制御
- Door Status Information (if supported by head unit)
No further manual operation of the decoder itself is typically required after initial setup.
6. メンテナンス
The RZ-FT52A CAN Bus Decoder is a low-maintenance electronic device. To ensure its longevity and proper function:
- 乾燥を保つ: デバイスを湿気や液体にさらさないでください。
- 優しく洗浄する: 清掃が必要な場合は、柔らかく乾いた布をご使用ください。刺激の強い化学薬品や研磨剤入りの洗剤は使用しないでください。
- 物理的損傷を避ける: Protect the device from impacts or excessive vibrations.
- 温度： Operate and store the device within normal automotive temperature ranges.
7。 トラブルシューティング
If you encounter issues after installing the RZ-FT52A CAN Bus Decoder, consider the following:
- No Functionality (e.g., steering wheel controls not working):
- 配線を確認してください: Double-check all physical connections to ensure they are secure and correctly wired according to the pin definition diagram (Figure 5). Improper wiring is a common cause of issues.
- Verify Head Unit Settings: Revisit the Android head unit's CAN Bus settings (Section 4.2) to confirm that "Raise" is selected as the manufacturer and your specific car model and year are correctly chosen.
- ヘッドユニットの互換性: Ensure your Android head unit is compatible (7", 8", 9", 10" units with 8-pin serial communication).
- "Car Name Not Displayed" during setup:
- This indicates a potential compatibility issue or an outdated head unit firmware. Ensure your head unit's software is up to date.
- If your specific car model is not listed in the head unit's CAN Bus settings, the decoder may not be fully compatible with your vehicle's specific CAN protocol.
- 断続的な機能:
- Loose connections can cause intermittent issues. Secure all plugs and wires.
- ボリュームをチェックtage fluctuations. Ensure the vehicle's electrical system is stable and within the decoder's operating voltage range (+9V~+16V).
8. ユーザーのヒント
- Verify Car Model Compatibility: While a list of compatible Toyota models is provided, always double-check if your exact model and year are supported by the decoder and your Android head unit's CAN Bus settings. For example, if you have a Toyota Land Cruiser Prado 120 from 2007, confirm its compatibility with the seller before installation, as the listed models are generally newer.
- Consult Head Unit Manual: The setup process on the Android head unit can vary. Always refer to your specific head unit's instruction manual for detailed steps on accessing factory settings and CAN Bus configuration.
- 写真を撮る： Before disconnecting any wires, take clear photos of your existing wiring. This can be invaluable for reference during installation or troubleshooting.
9. 保証とサポート
For any questions, technical support, or assistance with installation or troubleshooting, please contact the seller directly. Provide your product model (RZ-FT52A) and a detailed description of your issue, including your vehicle's make, model, year, and the Android head unit model you are using.
The manufacturer, Raise, and the brand, Pinmany, are committed to providing support for their products.