Creality K1/K1 MAX マザーボード ユーザーマニュアル

1. はじめに

This manual provides essential information for the installation, operation, and maintenance of your Creality K1 or K1 MAX Motherboard. This upgraded silent board, featuring a 32-bit architecture and TMC2209 drivers, is designed to enhance the performance and reduce noise levels of your 3D printer. Please read this manual carefully before proceeding with any installation or operation.

2.製品オーバーview

The Creality K1/K1 MAX Motherboard is a high-performance mainboard designed for Creality K1 and K1 MAX 3D printers. It integrates advanced features for stable and quiet operation.

3. 仕様

4. セットアップとインストール

重要な安全上の注意事項:

• Always power off and unplug your 3D printer from the mains before beginning any installation or maintenance.
• Discharge any static electricity from your body before handling the motherboard to prevent damage to sensitive electronic components.
• Use appropriate tools and follow the specific disassembly/assembly instructions for your Creality K1 or K1 MAX printer model.

インストール手順（一般）:

1. 準備： Ensure your workspace is clean and well-lit. Gather necessary tools (screwdrivers, anti-static wrist strap if available).
2. Access the Existing Motherboard: Carefully open your 3D printer's control box or access panel to expose the current motherboard. Refer to your printer's specific service manual for exact steps.
3. コンポーネントを切断します: Systematically disconnect all cables from the old motherboard. It is highly recommended to take photos or label each cable before disconnecting to ensure correct re-connection.
4. 古いマザーボードを取り外す: Unscrew the old motherboard from its mounting points and carefully remove it.
5. 新しいマザーボードをインストールします。 Place the new Creality K1/K1 MAX motherboard into position, aligning it with the mounting holes. Secure it with the provided screws (refer to Figure 2.5).
6. コンポーネントを再接続します。 Reconnect all cables to the new motherboard, using your photos or labels as a guide. Ensure all connections are firm and correctly oriented.
7. Close Up: Carefully close the control box or access panel.
8. 初回電源オン: Plug in and power on your 3D printer. Observe for any unusual behavior or error messages.

ファームウェア： The motherboard is typically shipped with pre-installed firmware. However, it is always recommended to check for the latest firmware version on the official Creality website and update if necessary after installation to ensure optimal performance and access to the newest features.

Motor Compatibility Note:

When replacing motors, specifically the 42-48 X-axis and Y-axis motors, please note that compatibility with the latest K1 Max motherboard is ensured for K1 Max models manufactured before 2024. Always verify motor specifications and compatibility with your specific printer model and motherboard version.

5. 操作

The motherboard serves as the central control unit for your 3D printer. Once installed and properly configured, it manages all printer functions, including motor movements, heating elements, sensor readings, and communication. For detailed operational instructions, refer to the user manual specific to your Creality K1 or K1 MAX 3D printer model, as the motherboard's function is integrated within the printer's overall system.

6. メンテナンス

Proper maintenance ensures the longevity and optimal performance of your motherboard:

• 清潔に保ちます： Regularly inspect the motherboard for dust and debris. Use compressed air or a soft brush to gently clean the surface. Ensure the printer is powered off and unplugged before cleaning.
• 湿気を避ける: Keep the printer and motherboard away from liquids and high humidity environments.
• 適切な取り扱い: When handling the motherboard, always hold it by the edges to avoid touching components, especially with bare hands, to prevent static discharge damage.
• 換気： Ensure the printer's enclosure has adequate ventilation to prevent overheating of the motherboard and other electronic components.

7。 トラブルシューティング

If you encounter issues after installing the new motherboard, consider the following:

• No Power/Boot Issues: Double-check all power connections to the motherboard and ensure the power supply is functioning correctly. Verify the printer's power switch is on.
• プリンターが応答しません: Confirm all ribbon cables and motor connections are securely seated and correctly oriented. Incorrect wiring can lead to non-responsive components.
• Unusual Noises/Movements: This could indicate incorrect motor wiring or driver issues. Power off immediately and re-check all motor connections against your documentation or photos taken during disassembly.
• ファームウェアの問題: If the printer behaves erratically, consider reflashing the firmware. Download the correct firmware for your specific printer model (K1 or K1 MAX) and motherboard version from the official Creality webサイト。
• エラーメッセージ: Note down any error messages displayed on the printer's screen. These messages often provide clues to the underlying problem. Consult Creality's support resources or community forums with the error code.

8. ユーザーのヒント

• Firmware Verification: While motherboards typically ship with firmware pre-installed, it's a good practice to verify the installed version and check for updates on the official Creality website after installation. This ensures you have the latest features and bug fixes.
• ケーブル管理 During installation, pay close attention to cable routing. Proper cable management not only makes future maintenance easier but also prevents cables from interfering with moving parts or causing shorts.
• 静電気防止: Always use an anti-static wrist strap or frequently touch a grounded metal object before and during handling the motherboard to prevent electrostatic discharge (ESD) damage.

9. 保証とサポート

保証情報、技術サポート、サービスに関するお問い合わせは、Crealityの公式ウェブサイトをご覧ください。 website or contact your authorized Creality dealer. Keep your purchase receipt as proof of purchase for warranty claims.