SilverStone CS383 Full Tower NAS Chassis Instruction Manual

1. はじめに

The SilverStone CS383 is a high-performance full tower chassis designed for Network Attached Storage (NAS) and workstation applications. It supports a wide range of components, including SSI-EEB motherboards, multiple storage drives, and advanced cooling solutions. This manual provides detailed instructions for the assembly, operation, and maintenance of your CS383 chassis.

図1.1: 前面 view of the SilverStone CS383 chassis with the door open, showing the hot-swappable drive bays.

主な特徴:

• Supports motherboards up to E-ATX / SSI-EEB form factors.
• Includes 8 hot-swappable 3.5" or 2.5" drive trays with support for SAS-12G / SATA-6G drives.
• Features 8 expansion slots, accommodating GPUs or adapter cards up to 340mm in length.
• Supports liquid cooling radiators up to 420mm or air coolers up to 186mm tall.
• Capable of housing dual power supplies or up to 4 additional 5.25" drive bay devices.

2. システムセットアップ

2.1 シャーシの準備

Before installing components, ensure the chassis is placed on a stable, flat surface. Remove the side panels by unscrewing the thumbscrews at the rear and sliding the panels backward.

図2.1：側面 view of the CS383 chassis.

2.2マザーボードの取り付け

1. Install the necessary motherboard standoffs into the chassis tray according to your motherboard's form factor (SSI-EEB, SSI-CEB, E-ATX, ATX, Micro-ATX, Mini-ITX).
2. ネジ穴を合わせながら、マザーボードをスタンドオフの上に慎重に置きます。
3. マザーボードをネジで固定します。

Figure 2.2: Internal layout showing motherboard mounting area.

Figure 2.3: Workstation-grade component support, including SSI-EEB motherboard and dual PSU options.

2.3 Drive Installation (Hot-Swappable Bays)

The CS383 features eight hot-swappable drive bays for 3.5" or 2.5" SAS-12G / SATA-6G drives.

1. Open the front door of the chassis.
2. Press the release latch on a drive tray and pull it out.
3. Mount your 3.5" or 2.5" drive into the tray using the provided screws.
4. Slide the loaded drive tray back into the bay until it clicks into place.
5. Ensure all drives are properly connected to the backplane for power and data.

Figure 2.4: Detail of the hot-swappable drive bays.

Figure 2.5: Eight-bay hot-swap storage with drive status indicators.

2.4 電源の設置

The chassis supports standard ATX (PS2) power supplies and offers an optional secondary PSU slot.

1. Mount your primary power supply in the designated bottom-rear compartment.
2. Secure it with screws from the rear of the chassis.
3. For dual PSU configurations, install the second power supply in the lower front 5.25" bay area.

2.5 拡張カードの取り付け

The CS383 provides eight expansion slots for graphics cards, network adapters, or RAID controllers.

1. Remove the necessary slot covers from the rear of the chassis.
2. Insert your expansion card into the corresponding PCIe slot on the motherboard.
3. Secure the card with screws or the tool-less retention mechanism.

Figure 2.6: Expansion slots for adapter cards.

2.6 冷却システムの設置

The chassis supports various cooling configurations, including liquid cooling radiators up to 420mm and air coolers up to 186mm tall.

• ラジエーター: Mount liquid cooling radiators to the top panel.
• ファン: Two 92mm fans are pre-installed behind the drive bays for efficient cooling. Additional fans can be installed as needed.

Figure 2.7: Top panel supporting up to a 420mm liquid cooling radiator.

Figure 2.8: Internal component clearance diagram.

2.7 Additional Storage Options

Beyond the hot-swappable bays, the CS383 offers additional mounting points for 2.5" SSDs and 3.5" HDDs, as well as three 5.25" drive bays at the bottom front.

Figure 2.9: Additional 2.5" SSD and 3.5" HDD mounting locations.

Figure 2.10: Three 5.25" drive bays.

3. 操作

3.1 Front Panel Controls and I/O

The front panel provides essential controls and connectivity options:

• 電源ボタン: システムを起動またはシャットダウンします。
• リセットボタン: システムを再起動します。
• USB ポート: 外部機器を接続します。
• オーディオジャック: ヘッドフォンとマイク用。
• ドライブアクティビティ LED: Indicate read/write activity for each hot-swappable drive.

Figure 3.1: Front panel I/O and controls.

3.2 ホットスワップドライブ

The hot-swappable drive bays allow for adding or removing drives while the system is running, provided your operating system and RAID controller support this feature.

1. Ensure the drive is properly unmounted or ejected from the operating system before removal.
2. Open the front door and press the release latch on the desired drive tray.
3. Carefully pull the drive tray out.
4. To insert a new drive, mount it into an empty tray and slide it into the bay until it locks.
5. The operating system should detect the new drive automatically.

注記： Always refer to your operating system and RAID controller documentation for specific hot-swap procedures to prevent data loss.

4. メンテナンス

4.1 ダストフィルターのクリーニング

The CS383 includes removable dust filters in key areas to prevent dust buildup and maintain optimal cooling performance. Regular cleaning is recommended.

1. Locate the dust filters (e.g., at the bottom of the chassis).
2. Gently slide out or unclip the filters.
3. Clean the filters using compressed air or by rinsing them with water. Ensure they are completely dry before reinstallation.
4. フィルターを確実に取り付け直してください。

Figure 4.1: Removable dust filter at the bottom of the chassis.

4.2ファンのメンテナンス

Periodically check the chassis fans for dust accumulation. Clean them with compressed air to ensure unrestricted airflow.

注意： Disconnect power to the system before performing any internal cleaning or maintenance.

5。 トラブルシューティング

• システムが電源を入れない:
  • 電源装置が壁のコンセントに正しく接続されており、PSU の電源スイッチが「オン」の位置になっていることを確認します。
  • すべての電源ケーブル (24 ピン ATX、8 ピン CPU、PCIe、SATA) がマザーボードとコンポーネントにしっかりと接続されていることを確認します。
  • フロントパネルの電源ボタンとマザーボードの接続を確認します。
• ドライブが検出されません:
  • Confirm drives are fully seated in their hot-swap trays and the trays are locked into the bays.
  • Verify SATA/SAS data and power cables from the backplane are connected to the motherboard/RAID controller and power supply.
  • Check BIOS/UEFI settings to ensure SATA/SAS ports are enabled.
• 過熱の問題:
  • Ensure all chassis fans are spinning and not obstructed.
  • ダストフィルターと内部コンポーネントを定期的に清掃してください。
  • CPU クーラーと GPU ファンが正しく機能していることを確認します。
  • Consider optimizing fan curves in BIOS/UEFI or adding additional cooling if temperatures remain high under load.
• フロントパネルのI/Oが動作しない:
  • Check the internal cable connections from the front panel to the motherboard (USB headers, audio headers).

6. 仕様

7. 保証とサポート

7.1製品保証

SilverStone Technology products are covered by a limited warranty. The specific terms and duration of the warranty may vary by region and product. Please retain your proof of purchase for warranty claims.

7.2 テクニカルサポート

For technical assistance, troubleshooting, or further inquiries regarding your SilverStone CS383 chassis, please visit the official SilverStone Technology website or contact their customer support department. You can find contact information and support resources at www.silverstonetek.com.