RENESAS E2 Emulator RTE0T00020KCE00000R User Manual

1. はじめに

The RENESAS E2 Emulator (Model RTE0T00020KCE00000R) is a professional-grade in-circuit debugging and programming tool designed for the development of embedded systems utilizing Renesas RH850, RL78, and RX series microcontrollers. This device facilitates real-time code analysis, system optimization, and efficient firmware updates directly within the target system. It integrates seamlessly with Renesas development environments to streamline the embedded software development process.

2. 安全情報

Please read and understand all safety instructions before operating the E2 Emulator. Failure to follow these instructions may result in injury, damage to the product, or damage to connected devices.

• 電源： Use only the specified power supply for the emulator and target system.
• 環境： Operate the device in a dry, stable environment, away from extreme temperatures, humidity, and direct sunlight.
• 取り扱い： Handle the emulator with care. Avoid dropping or subjecting it to strong impacts.
• 接続: Ensure all connections are secure and correctly oriented before applying power. Disconnect power before making or breaking connections.
• 静電気： Take precautions against electrostatic discharge (ESD) when handling the emulator and target boards.
• 変更点: Do not attempt to modify or disassemble the emulator. Refer all servicing to qualified personnel.

3. パッケージ内容

以下にリストされているすべてのアイテムがパッケージに含まれていることを確認してください。

• RENESAS E2 Emulator (RTE0T00020KCE00000R)
• USBケーブル（PC接続用）
• Connection Cable (for target board connection)
• Software Development Tool (on media or available for download)
• クイックスタートガイド（または同様のドキュメント）

Image 1: RENESAS E2 Emulator and typical accessories. The image displays the compact E2 Emulator unit, a USB cable for connecting to a host PC, and a ribbon cable for connecting to the target microcontroller board.

4. セットアップ

Follow these steps to set up your E2 Emulator for use:

1. ソフトウェアをインストールする： Install the necessary Renesas Integrated Development Environment (IDE) and E2 Emulator drivers on your personal computer. Refer to the software documentation for specific installation instructions.
2. PCに接続: Connect the E2 Emulator to your personal computer using the provided USB cable. The PC should recognize the device and install any remaining drivers automatically.
3. Connect to Target Board: Connect the E2 Emulator to your target microcontroller board using the appropriate connection cable. Ensure the orientation is correct and the connection is secure. Refer to your target board's documentation for the correct debug header pinout.
4. Power On Target: Apply power to your target microcontroller board. The E2 Emulator typically draws power from the USB connection, but the target board requires its own power supply.
5. 接続を確認します: Launch your Renesas IDE (e.g., e² studio) and configure the debugger settings to detect and connect to the E2 Emulator and your target microcontroller.

5. 操作手順

The E2 Emulator supports various operations for developing and testing embedded applications.

5.1. Debugging Microcontrollers

To debug your application code:

• プログラムのロード: In your IDE, load the compiled program (e.g., .elf file) onto the target microcontroller via the E2 Emulator.
• Set Breakpoints: Place breakpoints in your source code where you want execution to pause.
• Start Debugging: Initiate the debugging session from the IDE. The program will execute on the target until a breakpoint is hit.
• Step Through Code: Use the IDE's debugging controls (step over, step into, step out) to navigate through your code line by line.
• Monitor Variables: Observe the values of variables, registers, and memory contents in real-time.
• Real-time Analysis: Utilize advanced debugging features for performance analysis and event tracing, if supported by your IDE and microcontroller.

5.2. Programming Microcontrollers

To program or re-program your microcontroller:

• ファームウェアの準備: Ensure you have the final firmware image (e.g., .hex, .mot, .srec file) ready for programming.
• デバイスの選択： In your IDE or dedicated programming tool, select the correct target microcontroller device.
• Configure Programmer: Configure the E2 Emulator as the programming tool.
• Erase/Program: Use the programming interface to erase the existing flash memory and then program the new firmware image onto the microcontroller.
• 確認する： After programming, perform a verification step to ensure the firmware was written correctly.

5.3. Supported Microcontroller Families

The E2 Emulator is compatible with the following Renesas microcontroller families:

• RH850シリーズ
• RL78シリーズ
• RXシリーズ

For specific device support within these families, refer to the latest documentation provided by Renesas for the E2 Emulator and your chosen IDE.

6. メンテナンス

Proper maintenance ensures the longevity and reliable operation of your E2 Emulator.

• クリーニング： Use a soft, dry cloth to clean the exterior of the emulator. Do not use liquid cleaners or solvents.
• ストレージ： Store the emulator in a clean, dry, and dust-free environment when not in use.
• ケーブルのお手入れ: Avoid bending or crimping the USB and connection cables excessively. Inspect cables regularly for damage.
• ソフトウェアアップデート: Regularly check for and install the latest firmware and software updates for the E2 Emulator and your IDE from the official Renesas webサイト。

7。 トラブルシューティング

If you encounter issues with your E2 Emulator, try the following troubleshooting steps:

If the problem persists, consult the detailed documentation provided by Renesas or contact Renesas technical support.

8. 仕様

Key technical specifications for the RENESAS E2 Emulator (RTE0T00020KCE00000R):

9. 保証とサポート

保証： The manufacturer's warranty description states "No". Please refer to your point of purchase or Renesas' official website for any applicable regional or reseller-specific warranty information.

テクニカルサポート： For technical assistance, documentation, software downloads, and further information regarding the E2 Emulator, please visit the official RENESAS webサイトをご覧いただくか、認定サポート チャネルにお問い合わせください。