ANYCUBIC Water Washable 3D Printer Resin 2.0 User Manual

1. はじめに

This manual provides essential information for the safe and effective use of ANYCUBIC Water Washable 3D Printer Resin 2.0. This 405nm high-precision photopolymer resin is designed for 4K/8K/12K capable LCD and DLP 3D printers, offering low shrinkage and easy water-washable post-processing. Please read this manual thoroughly before use to ensure optimal printing results and safety.

2. 安全上の注意

Handling 3D printer resin requires adherence to safety guidelines to prevent potential health hazards. Always prioritize your safety.

• 保護具を着用する: Always wear gloves (nitrile or similar chemical-resistant gloves are recommended) and safety glasses to prevent skin and eye contact.
• 適切な換気を確保してください: Use the resin in a well-ventilated area to minimize inhalation of fumes. Consider using a respirator if ventilation is insufficient.
• 皮膚との接触を避ける: If resin comes into contact with skin, wash immediately with soap and water.
• 目を合わせないでください: If resin gets into eyes, flush immediately with plenty of water for at least 15 minutes and seek medical attention.
• 摂取: 飲み込まないでください。飲み込んだ場合は、吐かせないでください。直ちに医師の診察を受けてください。
• ストレージ： Store resin in a cool, dry, dark place, away from direct sunlight and heat sources. Keep the bottle tightly sealed when not in use. Keep out of reach of children and pets.
• 廃棄： Cured resin can be disposed of as regular plastic waste. Uncured liquid resin must be cured under UV light before disposal or disposed of according to local regulations for chemical waste. Do not pour liquid resin down drains.

3 製品の特徴

The ANYCUBIC Water Washable Resin 2.0 offers several advanced features for an improved 3D printing experience:

• Super Easy to Clean: Contains hydrophilic groups for good water solubility, allowing direct cleaning with water instead of alcohol. Compatible with Anycubic Wash and Cure Machine or ultrasonic cleaning.
• Anti-Yellowing & Stay Vibrant: Upgraded formula ensures models retain vibrant colors, especially effective for White and Transparent resins, even after prolonged exposure.
• Lower Shrinkage Rate & High Precision Models: Achieves precision up to 0.15mm, ideal for detailed miniature models.
• High-Resilience & Less Prone to Cracking: An elongation rate of 16.62% provides flexible, durable, and crack-resistant cured models.
• Less Odor for Indoor Use: Optimized formula significantly reduces resin odor during storage and printing for a more comfortable experience.
• Low Viscosity & High Print Success Rates: Enhanced platform adhesion ensures stable, high-quality prints with high success rates.
• 高い互換性: Compatible with a wide range of LCD and DLP 3D printers operating within the 365-405nm wavelength.

4. セットアップ

Before starting your print, ensure proper preparation of the resin and your 3D printer.

1. 樹脂ボトルを振る： Before each use, thoroughly shake the resin bottle for at least 1 minute to ensure all components are well mixed. This is crucial for consistent print quality.
2. 樹脂をバットに注ぎます: プリンターのレジンタンクに必要な量のレジンを慎重に注ぎます。レジンを入れすぎないようにしてください。
3. 環境条件: Ensure your printing environment is within the recommended temperature range (typically 20-25°C or 68-77°F) for optimal resin performance.

Image: ANYCUBIC Water Washable 3D Printer Resin 2.0 bottle. Always shake the bottle well before pouring resin into the vat.

5. 操作手順

Follow these steps for successful 3D printing with ANYCUBIC Water Washable Resin 2.0.

1. スライサー設定: Refer to the recommended printing parameters table below for initial slicer settings. Adjust layer thickness, normal exposure time, bottom exposure time, and other parameters based on your specific printer model and desired print quality.
2. 印刷を開始: Initiate the print job on your 3D printer. Monitor the first few layers to ensure proper adhesion to the build plate.
3. 後処理: After printing, carefully remove the build plate and printed model.

推奨される印刷パラメータ

Image: Recommended printing parameters for various Anycubic Photon 3D printers. This table provides guidance for layer thickness, exposure times, and lift speeds.

Note: These parameters are general guidelines. Optimal settings may vary based on your specific 3D printer model, ambient temperature, and desired print characteristics. Always perform calibration prints to fine-tune your settings.

Post-Processing Steps

1. サポートを削除する: Carefully remove any necessary supports from your printed model.
2. 水洗い： Clean the model using water. This can be done manually, with an ultrasonic cleaner, or with a dedicated wash and cure station. Ensure all uncured resin is removed from the surface and crevices.
3. 乾燥: Allow the model to air dry completely or use compressed air to speed up the process. Ensure no water remains on the surface before curing.
4. Final Curing: Place the cleaned and dried model under a UV light source (e.g., a UV curing station or direct sunlight) to fully cure the resin. Curing times vary based on UV intensity and model thickness.

Image: A 3D printed elephant model submerged in water, illustrating the water-washable feature of the resin. Post-processing is simplified as it only requires water.

Image: A side-by-side comparison of a 3D printed model before and after washing and curing, demonstrating the improved finish and detail.

6. メンテナンス

適切なメンテナンスを行うことで、樹脂とプリンターのコンポーネントの寿命が長くなります。

• 樹脂バットの洗浄： After printing, if you do not plan to print again soon, filter any remaining resin back into its original bottle using a resin filter. Clean the resin vat with water and a soft cloth.
• ビルドプレートのクリーニング: Clean the build plate with water immediately after removing the print. Dry thoroughly before the next print.
• 樹脂の保管: Store the resin bottle in a cool, dark place, away from direct UV light. Ensure the cap is tightly sealed to prevent contamination and premature curing.

Image: Multiple options for water washing 3D prints, including using an Anycubic Wash & Cure machine, washing in a container, or ultrasonic washing. Always dispose of residual liquid responsibly.

7。 トラブルシューティング

Common issues and their potential solutions when using 3D printer resin.

• Prints Not Sticking to Build Plate:
  • 下部の露出時間を長くします。
  • ビルド プレートが適切に水平になっており、清潔であることを確認します。
  • Increase the initial layer contact area in your slicer.
• Failed Prints / Partial Prints:
  • Check exposure times; they might be too low.
  • Verify resin temperature is within the recommended range.
  • Inspect the FEP film for damage or cloudiness.
  • 樹脂が十分に混合されていることを確認します。
• Models are Brittle:
  • Ensure models are fully cured. Increase final curing time.
  • Check if the resin has expired or been improperly stored.
• Models are Sticky After Washing:
  • Ensure thorough washing to remove all uncured resin.
  • Increase washing time or agitation.
  • Ensure models are completely dry before final curing.

8. 仕様

Detailed technical specifications for ANYCUBIC Water Washable 3D Printer Resin 2.0.

Image: A table detailing the physical and mechanical properties of the resin, such as viscosity, density, surface hardness, and various strength metrics.

9.保証とサポート

For warranty information, technical support, or further inquiries, please visit the official ANYCUBIC webサイトをご覧いただくか、カスタマー サービスに直接お問い合わせください。

ANYCUBIC公式ストア: AmazonのANYCUBICストアをご覧ください

Always refer to the latest information available on the manufacturer's official channels for the most up-to-date support and warranty details.