SENSTREE Dual Probe Temperature & Humidity Controller

1. はじめに

This manual provides detailed instructions for the installation, operation, and maintenance of your SENSTREE Dual Probe Temperature & Humidity Controller, Model THT1032-ZJ. This device is designed to precisely monitor and control both temperature and humidity in various environments, utilizing independent sensors for optimal performance. Please read this manual thoroughly before use to ensure safe and efficient operation.

2. 安全情報

怪我やデバイスの損傷を防ぐために、次の安全上の注意事項を守ってください。

• 電源のボリュームを確認してくださいtage matches the device's specifications (240 Volts AC).
• Do not immerse the controller unit in water or expose it to excessive moisture. The probes are water-resistant, but the main unit is not.
• Avoid exceeding the maximum rated current of 10 Amps per outlet. Overloading can cause damage or fire.
• デバイスを子供の手の届かない場所に保管してください。
• ご自身でユニットを分解したり修理したりしないでください。修理が必要な場合は、資格のある担当者にご連絡ください。
• 過熱を防ぐために、コントローラーの周囲に適切な換気を確保してください。

3.製品オーバーview

3.1 コンポーネント

The SENSTREE Dual Probe Temperature & Humidity Controller consists of the main control unit, a temperature probe, and a humidity probe.

Figure 1: Main unit of the SENSTREE Dual Probe Temperature & Humidity Controller, showing the display, control buttons, three power outlets, and connected temperature and humidity probes.

3.2 主な特徴

• Dual-Probe Design: Features separate temperature and humidity sensors for independent, precise monitoring and control.
• デュアルディスプレイ： Clear LCD screen simultaneously shows real-time temperature (°F/°C) and humidity (%).
• 幅広い用途: Suitable for greenhouses, reptile terrariums, grow tents, wine cellars, and storage rooms. Compatible with humidifiers, dehumidifiers, heaters, AC units, and fans.
• 精密エンジニアリング: High-accuracy sensors and advanced calibration ensure reliable performance. Alerts for out-of-range conditions protect sensitive environments.
• 使いやすい： Simple setup and intuitive buttons for setting desired ranges and automatic device activation.

4. セットアップ

4.1 開梱

Carefully remove the controller and its components from the packaging. Verify that all parts are present and undamaged.

4.2コントローラーの取り付け

The controller features a hanging design for convenient placement.

Figure 2: The back of the controller unit features keyhole slots for wall mounting using screws (not included).

1. Select a suitable location for the controller, ensuring it is away from direct heat sources, moisture, and vibrations.
2. Use appropriate screws (not supplied) to secure the controller to a wall or vertical surface using the keyhole slots on the back.

4.3 プローブの接続

The controller comes with two independent probes: one for temperature and one for humidity.

Figure 3: The separate temperature probe (left) and humidity probe (right) for precise environmental measurements.

1. Plug the temperature probe into the designated port on the controller.
2. Plug the humidity probe into its designated port.
3. Position the probes in the area where you need to monitor temperature and humidity. Ensure they are not obstructed and are representative of the environment you wish to control. The sensor length is approximately 1.4 meters (55.12 inches).

4.4電源オン

1. コントローラーの電源コードを標準の 240V AC 電源コンセントに差し込みます。
2. The LCD display will illuminate, showing current temperature and humidity readings.

5. 操作手順

5.1ディスプレイオーバーview

The LCD screen provides real-time information and settings.

Figure 4: The controller's backlit LCD display showing temperature (OUT1), humidity (OUT2), and a clock/timer (OUT3).

• OUT1： Displays current temperature and heating/cooling status.
• OUT2： Displays current humidity and humidification/dehumidification status.
• OUT3： Displays current time or timer status.

5.2 温度と湿度の設定

To set your desired temperature and humidity ranges:

1. を押す セット ボタンを一度押すと温度設定モードになります。温度表示が点滅します。
2. 使用 UP そして 下 arrow buttons to adjust the desired temperature set point.
3. プレス セット again to confirm the temperature and move to the temperature differential setting (hysteresis). Adjust as needed.
4. プレス セット a third time to enter humidity setting mode. The humidity display will flash.
5. 使用 UP そして 下 arrow buttons to adjust the desired humidity set point.
6. プレス セット a fourth time to confirm the humidity and move to the humidity differential setting. Adjust as needed.
7. プレス セット one last time or wait a few seconds for the settings to save automatically and return to normal display.

5.3 モード選択

The controller supports various operating modes for temperature and humidity control.

1. を押し続けます モード button for 3 seconds to enter mode selection.
2. 使用 UP そして 下 arrow buttons to cycle through available modes (e.g., Heating, Cooling, Humidification, Dehumidification, Timer).
3. プレス モード もう一度クリックして選択を確定します。

5.4 タイマー機能

The OUT3 port can be configured as a timer. Refer to the detailed instructions in the full manual for specific timer programming steps.

6. メンテナンス

To ensure the longevity and accuracy of your controller:

• クリーニング： 本体は柔らかく乾いた布で拭いてください。研磨剤入りの洗剤や溶剤は使用しないでください。
• プローブのお手入れ: Keep the probes clean and free from debris. Avoid bending or damaging the probe cables.
• ストレージ： If storing the device for an extended period, disconnect it from power and store it in a dry, cool place.

7。 トラブルシューティング

一般的な問題とその解決策については、以下の表を参照してください。

8. 仕様

Technical specifications for the SENSTREE Dual Probe Temperature & Humidity Controller:

9. 保証とサポート

The SENSTREE Dual Probe Temperature & Humidity Controller comes with a 12ヶ月保証 from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.

For technical support, troubleshooting assistance, or warranty claims, please contact SENSTREE customer service through the retailer where the product was purchased or visit the official SENSTREE web連絡先情報のサイト。