Diyeeni ATS-20+

ATS-20+ Si4732 Full Band Radio Receiver User Manual

Model: ATS-20+

導入

The Diyeeni ATS-20+ Si4732 Full Band Radio Receiver is a versatile digital receiver designed for global reception. It supports FM stereo, AM (MW and SW), and SSB (LSB and USB) bands, offering a wide range of radio frequencies for various listening needs. Its compact and robust design makes it suitable for both indoor and outdoor use.

パッケージ内容

パッケージを開封したら、以下のアイテムがすべて含まれていることを確認してください。

  • 1 x ATS-20+ Radio Receiver
  • 1 xアンテナ
  • タイプC充電ケーブル x 1
  • 1 x Set of Foot Mats (4 pieces)
ATS-20+ Radio Receiver and accessories

Image: The ATS-20+ radio receiver shown with its included antenna, Type-C charging cable, and foot mats.

製品終了view

フロント view of ATS-20+ Radio Receiver

画像: 正面 view of the ATS-20+ radio receiver, showing the display, tuning knob, and main controls.

戻る view of ATS-20+ Radio Receiver with antenna port and charging port

画像: 裏面 view of the ATS-20+ radio receiver, highlighting the antenna connection point and the Type-C charging port.

Close-up of ATS-20+ Radio Receiver display and controls

画像: クローズアップ view of the ATS-20+ radio receiver's 0.96-inch screen and control buttons, demonstrating its compact size when held.

The ATS-20+ features a compact design with a 0.96-inch screen for clear display of frequency and settings. It includes a Type-C charging interface and an integrated 800mAh Lithium Ion Battery. The main controls consist of a tuning/BFO/ATS knob and buttons for band selection, volume, bandwidth, and mode.

設定

1. バッテリーの充電

Before first use, fully charge the radio receiver. Connect the supplied Type-C charging cable to the radio's Type-C port and the other end to a standard USB power adapter (not included) or a computer USB port.

  • 充電中は充電インジケータライトが点灯します。
  • フル充電には通常約 2 ～ 3 時間かかります。

2. アンテナの取り付け

Screw the provided telescopic antenna into the antenna connector on the side of the radio. Ensure it is securely fastened for optimal reception.

側 view of ATS-20+ Radio Receiver with antenna attached

画像: サイド view of the ATS-20+ radio receiver, showing the telescopic antenna attached to its connector.

3. Applying Foot Mats

For stability and to prevent scratching surfaces, peel and stick the four included foot mats to the bottom corners of the radio receiver.

操作手順

1. 電源のオン/オフ

を押し続けます オフ/オン ラジオの電源をオンまたはオフにするボタン。

2. バンドの選択

を押す バンド+ or バンド- buttons to cycle through the available frequency bands: FM, AM (MW, SW), and SSB (LSB, USB).

3.チューニング

大きな TUNE/BFO/ATS knob to adjust the frequency. A short press on this knob may switch between fine tuning and coarse tuning modes, or activate ATS (Automatic Tuning System) depending on the current mode.

4. 音量調整

使用 巻+ そして vol- buttons to increase or decrease the audio volume.

5. Bandwidth (BW) Selection

を押す BW button to cycle through different audio bandwidth filters (e.g., 0.5, 1, 1.2, 2.2, 3, and 4 KHz). Selecting the appropriate bandwidth can improve signal clarity and reduce interference.

6. Mode Selection (SSB)

When in SSB mode, use the モード button to switch between LSB (Lower Sideband) and USB (Upper Sideband).

7. Step Adjustment

の ステップ button allows you to change the tuning step size, which can be useful for precise tuning or quickly scanning frequencies.

Close-up of ATS-20+ Radio Receiver display and control buttons

画像: 詳細な view of the ATS-20+ radio's screen and the various control buttons for band, volume, bandwidth, and mode selection.

メンテナンス

  • クリーニング： ラジオの外装を清掃する際は、柔らかく乾いた布を使用してください。液体クリーナーや研磨剤は使用しないでください。
  • ストレージ： 長期間使用しない場合は、ラジオを直射日光や極端な温度を避け、涼しく乾燥した場所に保管してください。
  • バッテリーのケア： バッテリーの寿命を延ばすには、バッテリーを頻繁に完全に放電させないでください。ラジオを使用していない場合でも、定期的にバッテリーを充電してください。
  • アンテナのケア: Handle the telescopic antenna carefully to prevent bending or breaking. Retract the antenna when not in use or during transport.
ATS-20+ Radio Receiver made of aluminum alloy

Image: The ATS-20+ radio receiver, highlighting its durable aluminum alloy construction, designed for ruggedness and long service life.

トラブルシューティング

問題考えられる原因解決
電源なし電池が消耗しています。Type-C ケーブルを使用してラジオを充電します。
受信状態が悪い / 雑音があるAntenna not extended or connected properly; Weak signal; Interference.Fully extend the antenna and ensure it's securely connected. Try repositioning the radio. Adjust the bandwidth (BW) filter.
Cannot tune to desired stationIncorrect band selected; Tuning step too large.Verify you are on the correct frequency band (FM, AM, SW, SSB). Adjust the tuning step using the STEP button for finer control.
Distorted audio in SSB modeIncorrect sideband (LSB/USB) selected; BFO not properly adjusted.Switch between LSB and USB using the MODE button. Fine-tune the BFO (Beat Frequency Oscillator) using the TUNE/BFO/ATS knob for clear audio.

仕様

特徴詳細
モデルATS-20+
画面0.96インチ
充電インターフェースタイプC
スピーカー8Ω 1.5W
電池のタイプ800mAh Lithium Ion Battery (Built-In)
サポートされている周波数帯FM, AM (MW and SW), SSB (LSB and USB)
Sound Bandwidth Filters0.5、1、1.2、2.2、3、4 kHz
Pre-configured Bands22 commercial and amateur radio bands
寸法（パッケージ）5.94 x 4.06 x 2.24インチ
重量（パッケージ）11.11オンス
材料金属、PCB

保証情報

This product is covered by a standard manufacturer's warranty. Please refer to the seller's policy on the purchase platform for specific warranty terms and duration. Retain your proof of purchase for any warranty claims.

保護プランは別途ご購入いただけます。

  • 2年間の保護プラン
  • 3年間の保護プラン
  • コンプリートプロテクト（月額プラン）

カスタマーサポート

For technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact the seller directly through the platform where the product was purchased. You may also visit the official Diyeeni store page for additional resources.

Diyeeni Store: https://www.amazon.com/stores/Diyeeni/page/FA40A778-A611-4117-B74A-56A2D97A5D82

© 2024 Diyeeni. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.