CREWORKS DUC-1003-00

CREWORKS 3L Ultrasonic Cleaner User Manual

Model: DUC-1003-00 | Brand: CREWORKS

導入

This manual provides detailed instructions for the safe and efficient operation, maintenance, and troubleshooting of your CREWORKS 3L Ultrasonic Cleaner. Please read this manual thoroughly before initial use and retain it for future reference.

安全上の注意

  • ユニットを分解しないでください。
  • Do not use flammable or corrosive liquids.
  • Always use sufficient fluid to cover items.
  • Unplug before filling & draining.
  • ユニットが安定した水平な面に設置されていることを確認してください。
  • お子様の手の届かない場所に保管してください。
CREWORKS 3L Ultrasonic Cleaner with digital display and open lid

Figure 1: CREWORKS 3L Ultrasonic Cleaner with its digital control panel and open lid, showcasing the stainless steel tank.

箱の中身

開梱したら、すべてのコンポーネントが揃っていて損傷がないことを確認してください。

  • 超音波洗浄機ユニット×1
  • ステンレススチールバスケット1個
  • 1 x電源コード
  • ユーザーマニュアル (本書) x 1

設定

  1. 配置: Place the ultrasonic cleaner on a firm, level, and dry surface, away from direct sunlight and heat sources. Ensure adequate ventilation around the unit.
  2. 電源接続: Connect the power cord to the unit and then to a grounded electrical outlet. Ensure the power switch on the back of the unit is in the OFF position before plugging in.
  3. タンクの充填: Open the lid and fill the stainless steel tank with an appropriate cleaning solution. The liquid level should be between the MIN and MAX marks, ensuring items to be cleaned are fully submerged but not overflowing. Do not operate the unit without liquid in the tank.
  4. Inserting Items: Place items to be cleaned into the stainless steel basket. Lower the basket gently into the tank. Avoid direct contact of items with the tank bottom to ensure optimal cavitation.
CREWORKS 3L Ultrasonic Cleaner control panel showing temperature and timer settings

Figure 2: Close-up of the intuitive digital control panel, displaying temperature and timer settings for easy operation.

操作手順

  1. 電源オン: Flip the main power switch located on the back of the unit to the ON position. The digital display will illuminate.
  2. 設定温度: Press the "TEMP" button to adjust the desired cleaning solution temperature. Use the up/down arrows to set the temperature between 68°F and 176°F (20°C and 80°C). The unit will begin heating automatically.
  3. タイマーの設定: Press the "TIME" button to adjust the desired cleaning duration. Use the up/down arrows to set the timer for up to 30 minutes.
  4. クリーニングを開始します: Once temperature and time are set, the ultrasonic cleaning process will begin. The display will show the remaining time.
  5. 動作中に: The unit will produce a slight humming sound and visible cavitation bubbles. This is normal. Avoid touching the tank or solution during operation.
  6. サイクルの終了: タイマーがゼロになると、ユニットは自動的に停止します。
  7. アイテムを削除: Carefully lift the basket out of the tank. Rinse the cleaned items under clean water and dry them thoroughly.
Diagram illustrating the ultrasonic cavitation process: formation, expansion, and bursting of bubbles for cleaning.

Figure 3: Illustration of the powerful ultrasonic cavitation process, where 40 kHz frequency sound waves create microscopic bubbles that implode, effectively cleaning intricate surfaces.

Before and after images showing cleaned glasses, razor, and circuit board using the ultrasonic cleaner.

Figure 4: Visual comparison demonstrating the effective cleaning results on various items, including eyeglasses, a razor, and a circuit board.

メンテナンス

  • タンクの排水: After each use, especially if the solution is dirty, unplug the unit and drain the liquid using the built-in drain valve. Tilt the unit slightly towards the drain for complete emptying.
  • タンクのクリーニング: Rinse the stainless steel tank with clean water. Wipe the interior and exterior of the unit with a soft, damp 布で拭いてください。研磨剤入りの洗剤を使用したり、本体を水に浸したりしないでください。
  • ストレージ: 使用しないときは、涼しく乾燥した場所に保管してください。保管する前に、タンクが完全に乾いていることを確認してください。
  • ヒューズの交換: In case of power issues, check the fuse located near the power inlet. Replace with a fuse of the same rating if necessary. (Note: Refer to the product's electrical specifications for fuse type and rating).
Images showing the stainless steel basin, noise-reducing cover, and non-skid rubber feet of the ultrasonic cleaner.

Figure 5: Key design features contributing to durability and stable operation, including the robust stainless steel basin, noise-reducing cover, and non-skid rubber feet.

トラブルシューティング

問題考えられる原因解決
ユニットの電源が入りません。電源コードが接続されていない、電源スイッチがオフ、ヒューズが切れている。Ensure power cord is securely plugged in; Turn power switch ON; Check and replace fuse if necessary.
No ultrasonic sound/cavitation.Insufficient liquid; Unit not started; Malfunction.Ensure liquid level is adequate; Press start button; Contact customer support if problem persists.
洗浄結果が悪い。Incorrect cleaning solution; Insufficient cleaning time; Overloaded tank; Items touching tank bottom.Use appropriate cleaning solution for items; Increase cleaning time; Do not overload; Use basket to suspend items.
加熱機能が動作しません。Temperature not set; Heater malfunction.Set desired temperature using the control panel; Contact customer support if problem persists.

仕様

特徴詳細
モデル番号DUC-1003-00
タンク容量3 L (0.8 ガロン)
超音波パワー120W
火力100W
超音波周波数40kHz
温度範囲68〜176°F(20〜80°C)
タイマー範囲1~30分
タンク材質食品グレード304ステンレス鋼
製品寸法13.5 x 7.6 x 11.81インチ
アイテム重量7.41 ポンド
Diagram showing the dimensions of the CREWORKS 3L Ultrasonic Cleaner and its internal basket.

Figure 6: Detailed dimensions of the ultrasonic cleaner unit and its removable cleaning basket.

保証とサポート

CREWORKS stands behind the quality of its products. This ultrasonic cleaner comes with a 1-Year Promiseご質問、技術サポート、保証請求については、当社までお問い合わせください。 24時間年中無休のカスタマーサービス. Refer to the product packaging or the official CREWORKS web連絡先の詳細についてはサイト。

For more information and support, visit the official CREWORKS Store: CREWORKS Store on Amazon.

© 2024 CREWORKS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.