Firecore G50 Laser Level User Manual

導入

The Firecore G50 self-leveling 360-degree 3-plane laser is a versatile tool designed for precision in various construction and home improvement tasks. It offers robust features for accurate and efficient work, including high visibility green beams, multiple operating modes, and extended battery life. This manual provides essential information for setup, operation, maintenance, and troubleshooting to ensure optimal performance and safety.

箱の中身

Upon unboxing your Firecore G50 Laser Level, please ensure all the following components are present:

• 1 x G50 Laser Level
• 充電式リチウムイオン電池2個
• リモコン x 1
• 1 x磁気ブラケット
• タイプC充電ケーブル x 1
• ポータブルバッグ x 1
• ユーザーマニュアル x 1

Image: Firecore G50 Laser Level, two batteries, magnetic bracket, remote control, Type-C charging cable, portable bag, and user manual.

設定

バッテリーの取り付けと充電

The Firecore G50 comes with two 3.7V / 4000mAh rechargeable Li-ion batteries. One battery is pre-installed. To install or replace a battery, open the battery compartment located at the bottom of the unit. Insert the battery, ensuring correct polarity, and close the compartment securely.

Batteries can be charged either while inside the unit or separately. To charge the unit directly, connect the provided Type-C charging cable to the charging port on the side of the laser level. The individual batteries also feature a Type-C charging port, allowing them to be charged independently. A full charge provides 7 hours of continuous use per battery, totaling 14+ hours with both batteries.

Image: Illustration of battery charging options: directly in the unit via Type-C, charging individual batteries via Type-C, and direct plugging for continuous power.

Mounting the Laser Level

The Firecore G50 can be mounted using its magnetic bracket or a standard tripod. The magnetic bracket features strong magnets for attachment to metal surfaces and a 1/4-inch screw thread for connecting to the laser level. The bracket also allows for fine vertical adjustment using a knob.

Image: The Firecore G50 Laser Level attached to its multifunctional magnetic bracket, demonstrating its ability to adhere to metal surfaces and adjust vertically.

動作モード

The Firecore G50 offers multiple operating modes to suit various leveling needs.

セルフレベリングモード

To activate self-leveling mode, slide the power switch to the 'ON' position. The laser will automatically level itself within ±4°. If the unit is outside this range, the laser lines will flash to indicate it cannot self-level. This mode is ideal for ensuring perfectly level and plumb lines for standard applications.

Image: A person using the Firecore G50 Laser Level in self-leveling mode, projecting horizontal and vertical lines onto a wall for precise alignment.

手動モード

For applications requiring lines at specific angles (e.g., diagonal lines), the manual mode can be used. To enter manual mode, ensure the power switch is 'OFF'. Then, press and hold the brightness button for 3 seconds. The laser lines will be locked in position, allowing you to project lines at any desired angle without self-leveling.

パルスモード

The pulse mode extends the working range of the laser up to 165 ft when used with an optional FD30 laser receiver. To activate pulse mode, press the brightness button while in self-leveling or manual mode. The laser lines will flash every 5 seconds, indicating pulse mode is active. This is particularly useful for outdoor use or in bright conditions where the laser lines might otherwise be difficult to see.

Image: The Firecore G50 Laser Level projecting green lines across a large, open space in pulse mode, indicating extended range capability with a receiver.

明るさ調整

The laser level features three levels of brightness adjustment to optimize visibility in different lighting conditions and conserve battery life. Press the brightness button to cycle through the different brightness settings.

Image: A user adjusting the brightness of the Firecore G50 Laser Level, with visual representations of 100%, 75%, and 50% brightness levels on a wall.

リモートコントロール機能

The included remote control allows for convenient adjustment of laser lines and brightness from up to 33 ft away, even through walls. This feature is particularly useful when the laser level is set up in a hard-to-reach location or when you need to make adjustments without disturbing the unit.

Image: A person using the remote control to adjust the Firecore G50 Laser Level, which is mounted on a pole, projecting multiple green lines across a room.

メンテナンス

To ensure the longevity and accuracy of your Firecore G50 Laser Level, follow these maintenance guidelines:

• レーザーレベルは清潔に保ち、ほこりやゴミが付かないようにしてください。清掃には柔らかく乾いた布を使用してください。
• ユニットを極端な温度や直射日光に長時間さらさないでください。
• Store the laser level in its portable bag when not in use to protect it from damage.
• バッテリーの健康を維持するために、長期保管する前にバッテリーが完全に充電されていることを確認してください。

トラブルシューティング

If your laser level is not functioning as expected, refer to the following common issues and solutions:

• Laser lines are flashing: This indicates the unit is outside its ±4° self-leveling range. Adjust the position of the laser level until the lines stop flashing and become stable.
• レーザーラインが暗い: Adjust the brightness setting using the brightness button on the unit or the remote control. Ensure batteries are fully charged.
• ユニットの電源が入らない: Check that the power switch is in the 'ON' position and that the batteries are properly installed and charged.

For further assistance, please refer to the detailed user manual or contact Firecore customer support.

仕様

保証とサポート

Firecore provides a 24-Month after-sale service and lifetime technical support for the G50 Laser Level. Please feel free to contact us if you have any concerns or require assistance.