1.製品オーバーview
The Slip Doctors Base Coat 2k Epoxy Primer Paint (Model BCPRIME) is a high-performance, two-part epoxy floor primer designed for industrial and commercial applications. This light gray primer provides a robust foundation for various topcoats, enhancing their durability and resistance to peeling and flaking. It offers exceptional corrosion resistance, protecting surfaces from weather damage and rust, and its chemically resistant formula makes it suitable for environments exposed to harsh substances.
This product is ideal for use in garages, warehouses, factories, workshops, showrooms, and other industrial facilities. It is formulated for easy application and is self-priming, ensuring smooth and effortless coverage.
Image 1.1: Slip Doctors Base Coat 2k Epoxy Primer Paint (Part A and Part B).
Image 1.2: Key features of the Base Coat Epoxy Primer.
2. 安全情報
Always prioritize safety when working with epoxy primers. Read and understand all safety data sheets (SDS) before use. The following general precautions should be observed:
- 換気： Ensure adequate ventilation during application and curing. Use respirators approved for organic vapors if ventilation is insufficient.
- 個人用保護具（PPE）： Wear appropriate PPE, including safety glasses or goggles, chemical-resistant gloves (e.g., nitrile or butyl rubber), and protective clothing to prevent skin contact.
- 皮膚接触: Avoid direct skin contact. If contact occurs, wash immediately with soap and water. Do not use solvents to clean skin.
- アイコンタクト: 目に入った場合は、直ちに多量の水で少なくとも 15 分間洗い流し、医師の診察を受けてください。
- 摂取: 飲み込まないでください。飲み込んだ場合は、吐かせないでください。直ちに医師の診察を受けてください。
- 可燃性: Keep away from open flames, sparks, and other ignition sources. Store in a cool, well-ventilated area.
- 廃棄： Dispose of all waste materials and empty containers in accordance with local, state, and federal regulations.
3. 表面処理
Proper surface preparation is critical for the successful adhesion and performance of the Base Coat epoxy primer. Failure to adequately prepare the surface can lead to premature coating failure, such as peeling or delamination.
3.1. 一般的な要件
- The surface must be clean, dry, and structurally sound.
- Remove all dirt, dust, grease, oil, loose paint, curing compounds, sealers, and other contaminants.
- The ambient and surface temperature should be between 50°F (10°C) and 90°F (32°C) during application and for at least 24 hours after. Relative humidity should be below 85%.
3.2. Concrete Surfaces
- クリーニング： Thoroughly clean the concrete surface. For oily or greasy areas, use a suitable degreaser and rinse thoroughly with clean water. Allow the surface to dry completely.
- プロファイリング: Concrete surfaces must be profiled to achieve a texture similar to 100-grit sandpaper (CSP 1-2). This can be achieved through mechanical methods such as grinding or shot blasting. Acid etching may be used as an alternative if mechanical methods are not feasible, but ensure all acid residue is neutralized and rinsed away.
- 修理： Repair any cracks, spalls, or damaged areas in the concrete using an appropriate concrete repair material. Allow repairs to cure fully before priming.
- 水分試験: Ensure the concrete is dry. Conduct a moisture test if there is any doubt. Moisture vapor transmission rates should be within acceptable limits for epoxy coatings.
図3.1: 例ample of a prepared surface in a commercial setting.
4. Mixing Instructions
The Base Coat 2k Epoxy Primer is a two-component system consisting of Part A (Primer) and Part B (Hardener). It is crucial to mix these components thoroughly and accurately to ensure proper curing and performance.
- Pre-mix Part A: Before combining, stir Part A (Primer) thoroughly with a mechanical mixer for 2-3 minutes to ensure all settled pigments are fully dispersed.
- コンポーネントを結合する: Pour the entire contents of Part B (Hardener) into the container of Part A (Primer).
- よく混ぜる: Mix the combined components with a mechanical mixer at a low speed (e.g., 300-450 RPM) for 3-5 minutes. Scrape the sides and bottom of the container during mixing to ensure a homogeneous blend. Improper mixing can lead to soft spots or uncured areas.
- Pot Life: Once mixed, the product has a limited pot life. Refer to the product label for specific pot life duration, which typically ranges from 30-60 minutes depending on temperature. Only mix what can be applied within this timeframe.
5. アプリケーション
Apply the mixed Base Coat epoxy primer evenly to the prepared surface.
- アプリケーションツール: Use a high-quality 3/8-inch nap roller, a squeegee, or a brush for application. For larger areas, a squeegee followed by back-rolling with a roller is often efficient.
- カバレッジ： The estimated coverage rate is approximately 300 square feet per gallon, depending on surface porosity and texture. Porous surfaces may require more material.
- Even Coat: Apply a thin, even coat. Avoid puddling or excessively thick areas, as this can lead to curing issues or an uneven finish.
- エッジとコーナー: Use a brush to cut in edges and corners before rolling the main areas.
- Single Coat: Typically, one coat of Base Coat primer is sufficient.
Image 5.1: Application of the epoxy primer using a roller.
Image 5.2: Benefits of proper application, including enhanced durability.
6. Curing and Drying
The Base Coat epoxy primer requires specific curing times before subsequent coats or traffic can be applied.
- Recoat Window: Refer to the product label for the recommended recoat window for your chosen topcoat. This is typically within 12-24 hours, but can vary based on temperature and humidity.
- Light Foot Traffic: The primer is typically ready for light foot traffic after 24 hours.
- Heavy Traffic / Full Cure: Allow a full 7 days for the primer to achieve its maximum hardness and chemical resistance before subjecting it to heavy traffic or chemical exposure.
- 温度と湿度: Curing times are affected by environmental conditions. Cooler temperatures and higher humidity will extend curing times, while warmer temperatures will shorten them.
7. メンテナンス
Once cured, the Base Coat epoxy primer provides a durable and easy-to-maintain surface. While it is a primer, proper care will contribute to the longevity of the entire flooring system.
- 定期清掃: 定期的に掃き掃除や掃除機をかけ、ほこりやゴミを取り除きます。
- スポットクリーニング： For spills, clean immediately with a mild detergent and water. Avoid abrasive cleaners or harsh solvents, as these can damage the coating.
- Chemical Spills: Although the primer offers chemical resistance, promptly clean up any chemical spills to prevent potential damage to the topcoat.
8。 トラブルシューティング
This section addresses common issues that may arise during or after the application of the Base Coat epoxy primer.
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Poor Adhesion / Peeling | Inadequate surface preparation (e.g., dirty, oily, or smooth surface), excessive moisture in concrete. | Ensure thorough cleaning and proper mechanical profiling of the surface. Address moisture issues before application. Remove failed coating and re-prepare. |
| Bubbling / Pinholes | Outgassing from porous concrete, rapid curing due to high temperature, applying too thick. | Ensure concrete is properly sealed and dry. Apply thinner coats. Work during cooler parts of the day or when temperatures are stable. |
| ムラのある仕上がり/縞模様 | Improper mixing, uneven application, incorrect roller nap. | Ensure components are thoroughly mixed. Apply evenly with consistent pressure. Use a high-quality roller with the recommended nap. |
| Soft Spots / Not Curing | Inaccurate mixing ratio, insufficient mixing, low temperatures. | Ensure precise measurement and thorough mixing of Part A and Part B. Maintain recommended application and curing temperatures. Remove uncured material and reapply. |
9. 仕様
| 特徴 | 詳細 |
|---|---|
| ブランド | スリップドクターズ |
| モデル番号 | BCPRIME |
| 色 | ライトグレー |
| 仕上げタイプ | 半光沢 |
| アイテムボリューム | 1ガロン（128液量オンス） |
| ペイントタイプ | エポキシ |
| 製品の具体的な用途 | Interior/Exterior, Garages, Warehouses, Factories, Workshops, Showrooms, Industrial Facilities |
| 表面の推奨事項 | Stone (Concrete) |
| 特集 | Chip Resistant |
| カバレッジ | Approximately 300 square feet per gallon |
| 完全硬化時間 | 7日間 |
| 耐水性レベル | 耐水性 |
| 欧州連合 | 850020279975 |
| メーカー | SlipDoctors |
Image 9.1: Ideal applications for the Base Coat primer.
Image 9.2: Base Coat compatibility with other Slip Doctors products.
10. 保証とサポート
For specific warranty information regarding the Slip Doctors Base Coat 2k Epoxy Primer Paint, please refer to the product packaging or contact Slip Doctors directly. As a small business brand, Slip Doctors is committed to customer satisfaction.
技術サポート、製品に関するお問い合わせ、またはサポートについては、製造元にお問い合わせください。
- メーカー: SlipDoctors
- Webサイト： Visit the Slip Doctors Store on Amazon