1. はじめに
The MJJC Foam Cannon S V3.0 is designed to enhance your car washing experience by producing thick, creamy snow foam. This manual provides detailed instructions for the safe and effective use, setup, operation, and maintenance of your new foam cannon.
Image: The MJJC Foam Cannon S V3.0 connected to a pressure washer, spraying thick foam onto a car.
2 製品の特徴
- Thicker Snow Foam Technology: The V3.0 is equipped with advanced technology to produce an even thicker, creamy foam, similar to shaving foam.
- 1/4 Inch Quick Connector: An adapter for a 1/4 inch quick connector is included for easy attachment to your pressure washer.
- 6 Key Upgrades:
- V3.0 Foam Technology: Achieves thick, shaving cream-like foam with minimal soap.
- V3.0 Structure: Allows for easier and smoother 360-degree spray control.
- V3.0 Straw Tube: Designed to consume all liquid in the bottle efficiently.
- V3.0 Bottle and Cap: Facilitates easier attachment of the bottle to the foam cannon body.
- MJJC Connection/Fitting: Ensures easier and faster attachment without the need for glue or PTFE tape.
- New Bottle Design: Features a more stable design to reduce the possibility of tipping over.
- Wide Operating Pressure Range: Compatible with pressure washers from 1300 psi to 3600 psi.
- Interchangeable Orifice Nozzles: Includes a pre-connected 1.25mm orifice nozzle (for 1600-2200 psi) and an additional 1.1mm orifice nozzle (for 1300-1600 psi). A 1.35mm or larger nozzle is recommended for 2200 psi or higher (sold separately).
- Tamp明らかなシール: Product packaging is secured with a tamper-evident seal for your assurance.
3. パッケージ内容
開梱時にすべてのアイテムが揃っていることを確認してください。
- MJJC Foam Cannon S V3.0 Unit
- 34 oz (1 Liter) Bottle
- 1/4 Inch Quick Connector Adapter
- 1.25mm Orifice Nozzle (pre-installed)
- 1.1mm Orifice Nozzle (additional)
- Weighted Straw Tube
- SOAP Sample (included with this variant)
Image: All parts of the MJJC Foam Cannon S V3.0 laid out, showing the main unit, bottle, and various accessories.
4. セットアップ
- Attach Straw Tube: Insert the weighted straw tube into the bottom of the foam cannon head. Ensure it is securely fitted.
- Attach Quick Connector: Screw the 1/4 inch quick connector adapter onto the foam cannon head. Hand-tighten is usually sufficient; no additional sealant is typically required due to MJJC's improved fitting design.
- 石鹸水を準備する: Fill the 34 oz bottle with water and your preferred car wash shampoo. The recommended dilution ratio is 1 part shampoo to 9 parts water. For optimal foam, MJJC's genuine foam gun shampoo is recommended.
- ボトルを取り付ける: Screw the filled bottle onto the foam cannon head. The V3.0 bottle and cap design makes this process easier and more secure.
- 高圧洗浄機に接続します: Attach the 1/4 inch quick connector of the assembled foam cannon to your pressure washer gun. Ensure a secure connection.
Image: Visual instructions for mixing soap, attaching the foam cannon, and beginning to spray.
5. 操作手順
- フォームの厚さを調整します: Use the top knob on the foam cannon to adjust the foam thickness. Turning it clockwise typically increases foam density, while counter-clockwise reduces it.
- スプレーパターンを調整する: The front nozzle can be rotated 360 degrees to change the spray pattern from a narrow stream to a wide fan. The V3.0 structure allows for smoother control.
- フォームを塗布する: Once connected and adjusted, activate your pressure washer and spray the foam onto your vehicle. Cover all surfaces evenly.
- 滞在時間: Allow the foam to dwell on the vehicle surface for a few minutes to loosen dirt and grime. Do not let the foam dry on the surface.
- リンス： After the foam has worked, rinse the vehicle thoroughly with clean water using your pressure washer, starting from the top and working downwards.
Image: The MJJC Foam Cannon S V3.0 effectively covering a car with snow foam.
6. メンテナンス
- 使用後は洗い流してください: After each use, empty any remaining soap solution from the bottle. Fill the bottle with clean water and run it through the foam cannon for 30-60 seconds to flush out any soap residue. This prevents clogging.
- Clean Orifice Nozzle: Periodically check the orifice nozzle for blockages. If foam production is reduced, the nozzle may be clogged. Use a small pin or needle to clear any obstructions.
- 接続を検査する: Regularly check all connections and O-rings for wear or damage. Replace worn parts to prevent leaks.
- ストレージ： Store the foam cannon in a clean, dry place away from direct sunlight and extreme temperatures.
7。 トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Weak or no foam production | Incorrect soap dilution, clogged orifice nozzle, insufficient pressure washer PSI, unsuitable shampうーん。 | Adjust soap-to-water ratio (1:9 recommended). Clean or replace orifice nozzle. Ensure pressure washer meets minimum PSI (1300 psi). Use a shampoo designed for foam cannons. |
| 接続部からの漏れ | Loose connections, worn O-rings, damaged fittings. | Tighten all connections. Inspect and replace any worn or damaged O-rings. Ensure fittings are not cross-threaded. |
| Bottle tipping over easily | Unstable placement, external force. | The V3.0 bottle has an improved design for stability. Ensure it is placed on a flat, stable surface when not in use. |
Shampoo Suitability
The type of shampoo used significantly impacts foam quality. Always use shampoos designed to lather well in a foam cannon. Some shampoos, especially those intended for direct application without dilution or those with wax/iron remover properties, may not produce adequate foam.
Video: This video demonstrates the importance of using suitable shampoo for optimal foam production with the MJJC Foam Cannon S V3.0. It shows examples of shampoos that lather well versus those that do not.
8. 仕様
- ブランド： MJJC
- モデル番号: PQRSV3
- 電源: 高圧洗浄機
- 動作圧力範囲： 1300psiから3600psi
- タンク容量： 1リットル（34オンス）
- 商品の重量: 1.19 キログラム (2.61 ポンド)
- 製品寸法: 長さ7.87インチ x 幅3.94インチ x 高さ11インチ
- ワンドの長さ: 7.87インチ
9. 保証とサポート
For warranty information and customer support, please refer to the product packaging or contact MJJC directly through their official webご購入いただいたサイトまたは販売店にお問い合わせください。保証請求の際に必要となりますので、購入証明書を保管してください。