CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser User Manual

導入

Thank you for choosing the CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser. This advanced system provides convenient access to purified cold and ambient water. Featuring a GAC filtration system, UV LED self-cleaning, and touchless dispense technology, it ensures a hygienic and refreshing hydration experience. This manual provides essential information for proper setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your dispenser.

図1: 前面 view of the CLOVER D25-B-TL Water Cooler Dispenser.

重要な安全情報

ご使用前に必ずすべての説明書をよくお読みください。この取扱説明書は、今後の参考のために保管してください。

• 電気安全: Ensure the dispenser is connected to a grounded electrical outlet. Do not use extension cords. Disconnect power before cleaning or servicing.
• 水道接続: Connect the dispenser only to a potable water supply. Ensure all connections are secure to prevent leaks.
• 配置: Place the dispenser on a flat, stable surface. Allow adequate clearance around the unit for ventilation.
• 子供とペット: Keep children and pets away from the dispenser, especially during operation and maintenance.
• 温度： This unit dispenses cold and ambient water only. It does NOT produce hot water.
• ダメージ： Do not operate the dispenser if it has a damaged cord or plug, or if it has been dropped or damaged in any way. Contact customer support.

パッケージ内容

以下にリストされているすべてのアイテムがパッケージに含まれていることを確認してください。

• CLOVER D25-B-TL Water Cooler Dispenser
• First Filter (GAC Purification System)
• ウォーターチュービング
• コネクタ
• Emergency Shutoff Valve
• Tubing Clips
• ユーザーマニュアル

Figure 2: Included installation kit components.

セットアップ手順

1. 開梱: Carefully remove the dispenser and all components from the packaging. Retain packaging for future transport if needed.
2. 配置: Position the freestanding dispenser on a level, stable surface. Ensure there is adequate space around the unit for proper ventilation, especially at the rear where the cooling coils are located. The dimensions are approximately 13.58"D x 12.2"W x 43.3"H.
3. フィルターのインストール：
   • Locate the filter housing, typically at the rear or bottom access panel of the unit.
   • Insert the provided GAC purification filter into the housing as per the arrows indicating water flow.
   • Secure the filter firmly.
   

   図3：内部 view illustrating filter placement and water tubing.
4. 給水接続:
   • Connect the water tubing from your potable water source to the dispenser's inlet using the provided connectors and emergency shutoff valve.
   • Ensure all connections are tight to prevent leaks. Use tubing clips to secure the tubing if necessary.
   • Slowly open the water supply valve to allow water to fill the dispenser's internal tank. Check for any leaks.
5. 電源接続: ディスペンサーをアース付き 120V AC 電源コンセントに差し込みます。
6. 初期フラッシュ: Before first use, dispense several cups of water from both cold and ambient spouts to flush the system and filter. Discard this water.

操作手順

The CLOVER D25-B-TL features touchless dispense and UV LED self-cleaning for enhanced hygiene.

1. 電源オン: Once plugged in, the dispenser will begin to cool the water. Allow approximately 1-2 hours for the water to reach optimal cold temperature (35.6°F).
2. Dispensing Water (Touchless):
   • Place your cup or container under the desired spout (cold or ambient).
   • Wave your hand in front of the sensor located above the spout. The water will begin to dispense.
   • Remove your hand to stop the water flow.
   

   Figure 4: Detail of the touchless dispense spouts and sensors.

3. UV LED Self-Cleaning: The dispenser is equipped with a UV LED self-cleaning system for enhanced water purification. This system operates automatically to maintain the hygiene of the internal water tanks. Refer to the indicator lights on the top panel for its status.

メンテナンス

Regular maintenance ensures the best performance and water quality from your dispenser.

1. フィルターの交換:
   • The GAC purification filter should be replaced periodically, typically every 6 months or as indicated by the dispenser's filter change indicator (if present).
   • Turn off the water supply and unplug the dispenser before replacing the filter.
   • Follow the filter installation steps in the Setup section to replace the old filter with a new one.
   • Flush the new filter as described in the Initial Flush step.
2. ドリップトレイのクリーニング: The ABS drip tray is easily removed for cleaning.
   • ドリップトレイを前方に引いて取り外します。
   • Empty any collected water and wash the tray with mild soap and water.
   • Rinse thoroughly and reinsert the tray.
3. 外装清掃: 外側の表面を柔らかい布で拭きます。amp 布で拭いてください。研磨剤や溶剤は使用しないでください。
4. タンク内部の洗浄： The UV LED self-cleaning system helps maintain internal hygiene. For additional cleaning, consult the manufacturer's website or customer support for specific instructions.

トラブルシューティング

カスタマー サポートに連絡する前に、次の一般的な問題と解決策を参照してください。

仕様

図 5: 配置の参考となる製品寸法。

保証とカスタマーサポート

For warranty information, product registration, or technical assistance, please contact CLOVER customer support.

メーカー: クローバー
Webサイト： CLOVER Official Store （一般的な製品情報について）
具体的な保証条件および連絡先の詳細については、購入書類を参照してください。