CLXEAST 18 Inch Illuminated Outdoor Atomic Analog Wall Clock Instruction Manual

導入

Thank you for choosing the CLXEAST 18 Inch Illuminated Outdoor Atomic Analog Wall Clock. This clock is designed to provide accurate timekeeping, temperature, and humidity readings for both indoor and outdoor environments. Featuring atomic time synchronization, an intelligent light sensor for illumination, and a durable weatherproof design, this manual will guide you through its setup, operation, and maintenance.

Image: The CLXEAST 18 Inch Illuminated Outdoor Atomic Analog Wall Clock, showcasing its bronze finish and classic dial with integrated thermometer and hygrometer.

設定

1. バッテリーの取り付け

The clock requires two types of batteries for full functionality:

• 1 x AA battery: Powers the atomic quartz movement for timekeeping.
• 4 x D size batteries: Powers the LED light sensor and atomic signal receiver.

電池を取り付けるには：

1. 時計の裏側にある電池ボックスを見つけます。
2. Open the cover for the AA battery compartment (usually a twist-off cap). Insert one AA battery, observing polarity (+/-).
3. Open the covers for the two D battery compartments. Insert two D batteries into each compartment, observing polarity (+/-).
4. Securely close all battery compartment covers.

画像: 背面 view of the clock, highlighting the battery compartments for AA and D batteries.

2. Time Zone and DST Settings

The clock features an atomic receiver that automatically synchronizes with the WWVB radio transmission from Fort Collins, CO. Before initial synchronization, set your time zone and Daylight Saving Time (DST) preference.

1. Locate the time zone selector switch (P/M/C/E for Pacific, Mountain, Central, Eastern) and the DST On/Off switch on the back of the clock, near the AA battery compartment.
2. Set the time zone switch to your desired USA time zone.
3. Set the DST switch to 'ON' if you observe Daylight Saving Time, or 'OFF' if you do not.

Image: A map illustrating the four USA time zones (Pacific, Mountain, Central, Eastern) for setting the atomic clock.

3. Initial Atomic Time Synchronization

After battery installation and settings, the clock will attempt to receive the WWVB atomic signal. This process can take several minutes to several hours, depending on your location and atmospheric conditions. For best reception, place the clock near a window or outdoors, away from large metal objects or electronic interference.

The clock hands will typically move to the 12 o'clock position and then automatically adjust to the correct time once the signal is received.

4. Thermometer and Hygrometer Calibration

The built-in thermometer and hygrometer require approximately 3 hours to fully calibrate and display accurate readings for the surrounding environment. Allow this time after initial setup or relocation.

5. 取り付け

The clock is designed for wall mounting. Use a sturdy screw or hook appropriate for the wall material and the clock's weight (approximately 5.3 lbs). Ensure the mounting location is stable and can support the clock securely.

操作手順

1. Automatic Timekeeping

Once synchronized, the atomic clock will automatically update its time daily to maintain accuracy to the second. It will also adjust for Daylight Saving Time if the DST option is enabled.

2. Smart LED Light Sensor Technology

The clock features an integrated light sensor that automatically activates a warm, ambient dial backlight during dark conditions and turns off in normal daylight. This feature is powered by the D batteries.

You can choose between two backlight modes:

• 常時オン: バックライトは常時点灯します。
• 常にオフ： バックライトはオフのままです。

Refer to the switch on the back of the clock to select your preferred mode.

Image: The clock face illuminated in a dark environment, demonstrating the smart LED backlight feature.

Image: A split image showing the clock's appearance during the day and its illumination at night.

3. 温度と湿度の表示

The clock features integrated analog displays for temperature and humidity. The thermometer measures temperatures from -40°F to 140°F, and the hygrometer measures relative humidity from 1% to 99%.

メンテナンス

1. バッテリーの交換

Replace the AA battery annually or when the clock hands stop moving. Replace the D batteries every 6-12 months, or when the LED backlight becomes dim or stops working. Always replace all D batteries at the same time for optimal performance.

2. 清掃

Clean the clock's face and frame with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish or clear lens.

3. 配置に関する推奨事項

While the clock is UV-resistant and weatherproof (IP65 standard), for lasting performance, it is recommended to place it in an area that is not constantly exposed to direct, harsh elements like extreme heat, prolonged direct sunlight, or continuous heavy rain.

Image: The outdoor clock being sprayed with water, demonstrating its waterproof capabilities.

トラブルシューティング

• Clock not setting time:
  • Ensure all batteries are new and correctly installed with proper polarity.
  • Verify the time zone and DST settings are correct.
  • Relocate the clock to an area with better reception, such as near a window or outdoors, away from electronic devices or metal structures that may interfere with the atomic signal.
  • Allow up to 24 hours for the clock to receive and process the atomic signal.
• LED backlight not working:
  • Check if the D batteries are fresh and correctly installed.
  • Ensure the LED light sensor switch is set to 'ON' or 'Always On' mode.
  • Confirm the ambient light conditions are dark enough for the sensor to activate the backlight.
• Temperature/Humidity readings inaccurate:
  • Allow at least 3 hours for the thermometer and hygrometer to acclimate to the environment after setup or relocation.
  • Ensure the clock is not exposed to direct heat sources or extreme cold that could skew readings.

仕様

保証情報

This CLXEAST product comes with a 12-month limited warranty from the date of purchase. This warranty covers manufacturing defects and workmanship under normal use. It does not cover damage resulting from misuse, accidents, unauthorized modifications, or improper installation. Please retain your proof of purchase for warranty claims.

カスタマーサポート

For any questions, technical assistance, or warranty inquiries, please contact CLXEAST customer support through the retailer's platform or visit the official CLXEAST web連絡先の詳細についてはサイト。