Perel TCA90000/SP1

Perel Washable HEPA Filter Instruction Manual

Model: TCA90000/SP1

導入

Thank you for choosing the Perel Washable HEPA Filter, model TCA90000/SP1. This filter is specifically designed for use with Perel Ash Vacuum Cleaners TCA90040 and TCA90041. Its HEPA filtration system efficiently captures fine ash particles, ensuring cleaner exhaust air. Being washable, it offers a reusable and economical solution for maintaining your ash vacuum cleaner.

セットアップとインストール

Follow these steps to properly install the HEPA filter into your Perel ash vacuum cleaner:

  1. 準備: Ensure the ash vacuum cleaner is unplugged from the power source before beginning installation.
  2. アクセスフィルターコンパートメント: Open the lid or access panel of your ash vacuum cleaner to locate the filter compartment. Refer to your ash vacuum cleaner's manual for specific instructions on accessing this area.
  3. 古いフィルターを削除します(該当する場合): If an old filter is present, carefully remove it. Dispose of the old filter according to local regulations.
  4. 新しいフィルターを挿入: Place the Perel Washable HEPA Filter (TCA90000/SP1) into the designated filter housing. Ensure it sits securely and creates a tight seal to prevent ash bypass.
  5. 安全なコンパートメント: Close the lid or access panel of the ash vacuum cleaner, ensuring it is latched correctly.
Perel Washable HEPA Filter, front view
画像1: フロント view of the Perel Washable HEPA Filter. This image shows the pleated filter material and the black plastic frame, indicating its design for efficient particle capture.

操作手順

Once the Perel Washable HEPA Filter is correctly installed, the ash vacuum cleaner is ready for use. The filter operates passively, capturing fine particles as air passes through it.

  • Always ensure the filter is clean and dry before operating the ash vacuum cleaner to maintain optimal suction and filtration efficiency.
  • Do not operate the ash vacuum cleaner without the HEPA filter installed, as this can lead to damage to the motor and release of fine ash into the environment.
  • Regularly check the filter for visible ash buildup during prolonged use to determine when cleaning is necessary.

メンテナンスと清掃

To ensure the longevity and effectiveness of your washable HEPA filter, regular cleaning is essential:

  1. 除去: Unplug the ash vacuum cleaner. Carefully remove the HEPA filter from its compartment.
  2. 初期クリーニング: Gently tap the filter against a hard surface (e.g., inside a trash can) to dislodge loose ash and debris.
  3. 洗浄: Rinse the filter under cold running water. Direct the water from the clean side (inside) to the dirty side (outside) to push out trapped particles. Continue rinsing until the water runs clear.
  4. 化学物質を避ける: Do not use detergents, soaps, or brushes, as these can damage the delicate HEPA material and reduce its filtration efficiency.
  5. 乾燥: Allow the filter to air dry completely before reinstallation. This typically takes 24 to 48 hours, depending on humidity. Do not use heat sources (e.g., hair dryer, oven) to speed up drying, as this can deform or damage the filter. Ensure the filter is completely dry to prevent mold growth and maintain performance.
  6. 再インストール: Once completely dry, reinstall the filter as described in the "Setup and Installation" section.

フィルターの交換: While washable, the filter's efficiency may decrease over time. Replace the filter if you notice any damage, tears, or if cleaning no longer restores adequate suction power.

Perel Washable HEPA Filter, angled view
画像2: 角度付き view of the Perel Washable HEPA Filter. This perspective highlights the pleated structure and the robust construction of the filter, designed for repeated washing.

トラブルシューティング

問題考えられる原因解決
吸引力の低下Filter is clogged with ash/debris. Filter is damp. Filter is incorrectly installed.Clean the filter according to the maintenance instructions. Ensure the filter is completely dry before use. Reinstall the filter correctly, ensuring a tight seal.
Ash escaping from vacuum exhaustFilter is damaged (tear/hole). Filter is not seated correctly.Inspect the filter for damage; replace if necessary. Reinstall the filter, ensuring it forms a tight seal within the compartment.
Unpleasant odor from vacuumFilter was not completely dry before reinstallation, leading to mold/mildew.Remove and thoroughly clean the filter. Ensure it is completely air-dried for at least 24-48 hours in a well-ventilated area before reinstallation. If odor persists, replace the filter.

仕様

  • ブランド: ペレル
  • モデル番号: TCA90000/SP1
  • 部品番号: 470150
  • 材料: HEPA(高効率粒子状空気)
  • 再利用性: 洗えて再利用できる
  • 個数: 1
  • 互換性: Designed for Perel Ash Vacuum Cleaners TCA90040 and TCA90041
  • ASIN: B0CKRTZ8NN

保証とサポート

Warranty information for this Perel HEPA filter is typically provided with the original ash vacuum cleaner or can be found on the official Perel website. For specific warranty details, claims, or technical support, please refer to the documentation included with your Perel ash vacuum cleaner or visit the manufacturer's official support channels.

Always ensure you are using genuine Perel replacement parts to maintain product warranty and optimal performance.

© 2024 Perel. 無断複写・転載を禁じます。

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.