ZTW Mantis G2シリーズ 85A ESC ユーザーマニュアル

1. はじめに

The ZTW Mantis G2 Series 85A Electronic Speed Controller (ESC) is an advanced 32-bit brushless speed controller designed for high-performance RC airplanes and fixed-wing aircraft. This ESC integrates a powerful 8A adjustable Switching BEC (SBEC) to provide stable power to your receiver and servos. It supports a wide range of battery configurations (3-8S LiPo/LiHV) and offers precise control and reliable operation for your aircraft's propulsion system.

Please read this manual thoroughly before installation and operation to ensure correct usage and maximize the performance and lifespan of your ESC.

2. 安全上の注意

Improper use of the ESC can lead to personal injury and damage to the product or associated equipment. Always observe the following safety guidelines:

• バッテリー接続: Always connect the battery with correct polarity. Reverse polarity will cause immediate and irreversible damage to the ESC.
• 絶縁： Ensure all connections are properly insulated to prevent short circuits.
• プロペラの安全性: Always remove the propeller from the motor before performing any setup, testing, or maintenance to prevent accidental injury.
• 熱： The ESC can generate significant heat during operation. Ensure adequate airflow for cooling and avoid touching it immediately after use.
• 水と湿気: Keep the ESC away from water, moisture, and conductive contaminants.
• 巻tage範囲： 指定された入力ボリュームを超えないようにしてくださいtage range (3-8S LiPo/LiHV).
• 子供たち： This product is not a toy and is not suitable for children under 18 years of age without adult supervision.

3 製品の特徴

• Advanced 32-bit microprocessor for precise control and rapid response.
• High-current capability: 85A continuous, 95A burst (10 seconds).
• ワイド入力ボリュームtage range: Supports 3-8S LiPo/LiHV batteries.
• Integrated 8A adjustable SBEC with selectable output voltages: 6V, 7.4V, or 8.4V.
• Designed specifically for RC airplane and fixed-wing applications.
• Multiple protection features including low-voltage cut-off, overheat protection, and throttle signal loss protection.
• Programmable via ZTW LCD Program Card G2 or dedicated Android/iOS mobile application.

4. 仕様

5. セットアップとインストール

Proper installation is crucial for the safe and efficient operation of your ESC. Follow these steps carefully:

1. モーター接続: Connect the three motor wires (typically labeled A, B, C or U, V, W) from the ESC to the corresponding wires on your brushless motor. The order may affect motor rotation direction; this can be adjusted later if needed.
2. バッテリー接続: Connect the main power wires (red for positive, black for negative) from the ESC to your LiPo/LiHV battery. Ensure the connector type matches and polarity is correct.
3. レシーバー接続: Plug the throttle signal cable (usually a three-wire servo connector) from the ESC into the throttle channel (typically channel 3) of your RC receiver.
4. SBEC巻tage選択： The Mantis G2 85A ESC features an adjustable SBEC. Refer to the programming section or the dedicated program card/app to set the desired output voltage (6V, 7.4V, or 8.4V) for your receiver and servos. Ensure the selected voltage is compatible with your receiver and servos.
5. 取り付け: Securely mount the ESC in your aircraft, ensuring good airflow for cooling. Avoid mounting it in enclosed spaces without ventilation.

6. 操作手順

Before first flight, it is essential to perform a throttle range calibration to ensure the ESC correctly interprets your transmitter's throttle stick positions.

6.1. Throttle Range Calibration

1. Turn on your transmitter and set the throttle stick to its maximum (full throttle) position.
2. バッテリーをESCに接続します。ESCからビープ音が連続して鳴ります。
3. After the initial beeps, the ESC will detect the full throttle signal and emit a confirmation tone.
4. Move the throttle stick to its minimum (zero throttle) position. The ESC will emit another series of beeps, indicating the throttle range has been successfully calibrated.
5. The ESC is now ready for normal operation.

6.2.通常の操作

After calibration, connect the battery with the throttle stick at minimum. The ESC will arm, indicated by a specific tone. You can then slowly advance the throttle to control the motor speed. Always ensure the propeller is clear before applying throttle.

7. ESCのプログラミング

The ZTW Mantis G2 85A ESC offers various programmable parameters to fine-tune its performance to your specific aircraft and preferences. Programming can be done using either the ZTW LCD Program Card G2 or the dedicated Android/iOS mobile application.

7.1. Programmable Parameters (Examples）

• ブレーキタイプ: Off, Soft, Medium, Hard.
• タイミング： Low, Medium, High (adjusts motor efficiency and temperature).
• カットオフVoltage: 音量を設定しますtage at which the ESC reduces or cuts power to protect the battery.
• 起動モード: Normal, Soft, Super Soft.
• SBEC巻tage: 6V, 7.4V, 8.4V.
• モーターの回転: Normal, Reverse.

Refer to the specific instructions provided with the ZTW LCD Program Card G2 or within the mobile application for detailed steps on how to connect and adjust these parameters.

8. メンテナンス

Regular inspection and basic maintenance will help ensure the longevity and reliable performance of your ESC:

• クリーニング： Keep the ESC free from dust, dirt, and debris. Use a soft brush or compressed air to clean the heat sink fins.
• 接続チェック: Periodically inspect all wire connections (motor, battery, receiver) for signs of wear, corrosion, or loose contacts.
• 物理的ダメージ: Check the ESC casing and wires for any physical damage after each flight.
• ストレージ： ESC は、直射日光や極端な温度を避け、乾燥した涼しい環境に保管してください。

9。 トラブルシューティング

If you encounter issues with your ZTW Mantis G2 85A ESC, refer to the following common problems and solutions:

• モーターが回転しない:
  • バッテリーの接続と充電レベルを確認してください。
  • Verify throttle signal cable is securely connected to the receiver.
  • スロットル範囲のキャリブレーションを再度実行します。
  • Ensure motor wires are correctly connected and not shorted.
• モーターが逆方向に回転する:
  • ESC とモーター間の 3 本のモーター ワイヤのうち 2 本を交換します。
  • Alternatively, reverse motor direction using the programming options.
• ESC Overheats:
  • ESC の周囲に十分な空気の流れを確保します。
  • Check if the propeller is too large or motor timing is too aggressive (adjust via programming).
  • バッテリー容量を確認するtage and current draw are within specifications.
• Intermittent Power/Loss of Control:
  • すべての接続部に緩みや腐食がないか確認してください。
  • Inspect for damaged wires or solder joints.
  • Ensure receiver and transmitter are functioning correctly and within range.

10. 保証とサポート

For warranty information and technical support regarding your ZTW Mantis G2 Series 85A ESC, please contact the retailer or the manufacturer, ZTW, directly. For purchases made through Buddy RC, please reach out to Buddy RC customer service for assistance.

保証請求の際に購入証明として購入レシートを保管してください。