JMT HLK-LD2450 24GHz Trajectory Sensor Module User Manual

1.製品オーバーview

The JMT HLK-LD2450 is a 24GHz radar module designed for real-time tracking of moving targets within a detection area. It provides distance, angle, and speed information of these targets via a serial port. This module is primarily intended for indoor applications such as smart homes, offices, and hotels, enabling precise positioning and tracking of people.

図1: 以上view of the JMT HLK-LD2450 radar module, illustrating its compact design for human movement trajectory tracking.

2. 主な特徴

• 軌道追跡: Real-time tracking of moving targets, outputting distance, angle, and speed data.
• Application Scenes: Optimized for indoor environments including homes, offices, and hotels for human presence and movement detection.
• 検出角度: Azimuth ± 60° / Tilt ± 35°.
• 角度精度: 2°～20°。
• 検出距離: Maximum sensing distance of 8 meters.
• 距離測定精度： 0.15メートル。
• データ出力: Serial ASCII format.
• 変調モード: FMCW (Frequency Modulated Continuous Wave).
• 頻度： 24G-24.25GHz (ISM band).
• Sweep Bandwidth: 250MHz (CE/FCC compliant).
• シリアルポートボーレート: 256000, with 1 stop bit and no parity bit.
• パッケージ： Default 1.5mm x 4Pin Female connector.

3. 技術仕様

4. セットアップ手順

This section details the physical connection and initial configuration of the HLK-LD2450 module.

4.1. モジュールインターフェース

The module features a 4-pin interface for power and serial communication. Refer to the diagram below for pin assignments.

図2: HLK-LD2450 module dimensions and interface pinout. The module measures 15mm x 40mm.

• 1: VCC - 5V Power Input
• 2: アース - 電源グランド
• 3: テキサス州 - Serial Transmission (Output from module)
• 4: RX - Serial Port Reception (Input to module)

正しい極性と容量を確認してくださいtage when connecting the power supply. Incorrect connections may damage the module.

4.2. 物理的な設置

The module is suitable for wall-mounted installation in indoor environments. Consider the detection angle specifications (Azimuth ± 60° / Tilt ± 35°) to optimize coverage for the desired tracking area.

図3: The HLK-LD2450 module showing the pin headers for connection, designed for motion positioning and tracking.

5. 操作手順

The HLK-LD2450 module communicates via a serial port, outputting target information in ASCII format.

5.1. Serial Communication Parameters

• ボーレート： 256000
• ストップビット： 1
• パリティビット： なし

5.2. Using the Configuration Tool

To interact with the module and retrieve data, use the dedicated Configuration Tool (software provided separately by the manufacturer, if applicable). Follow these steps:

1. Connect the HLK-LD2450 module to your computer via a serial interface (e.g., USB-to-serial converter).
2. Open the Configuration Tool software.
3. In the Configuration Tool, select the correct serial port number (COM port) corresponding to your connected module.
4. Ensure the serial port information (baud rate, stop bits, parity) matches the module's specifications (256000, 1 stop bit, no parity).
5. Click the "Detect Device" button within the Configuration Tool.
6. Once the module is detected, click "Start" to begin receiving moving target information from the detection area.

重要な注意: The serial port tool and the host tool cannot be used simultaneously. Ensure only one application is accessing the serial port at any given time.

6. メンテナンス

The JMT HLK-LD2450 module is designed for reliable operation with minimal maintenance. Adhere to the following guidelines:

• 環境条件: Operate the module within the specified ambient temperature range of -40°C to +85°C. Avoid exposure to extreme humidity, dust, or corrosive environments.
• クリーニング： 必要に応じて、モジュールの表面を柔らかく乾いた布で優しく拭いてください。液体クリーナーや溶剤は使用しないでください。
• 物理的な取り扱い: Handle the module with care to prevent physical damage to the PCB or components. Avoid bending or applying excessive force.
• 電源： Ensure a stable 5V power supply is used. Fluctuations or incorrect voltagパフォーマンスに影響を与えたり、モジュールが損傷したりする可能性があります。

7。 トラブルシューティング

This section provides solutions to common issues you might encounter with the HLK-LD2450 module.

7.1. No Data Output / Connection Issues

• 電力を確認します: Verify that the module is receiving a stable 5V power supply and that the VCC and GND connections are correct.
• Serial Port Selection: Ensure the correct COM port is selected in your Configuration Tool or serial terminal software.
• Serial Port Parameters: Confirm that the baud rate is set to 256000, with 1 stop bit and no parity bit.
• ケーブル接続: Inspect all serial communication cables for proper connection and integrity. Ensure TX and RX lines are correctly cross-connected if using a direct serial connection (TX of module to RX of host, RX of module to TX of host).
• ソフトウェアの競合: Remember that the serial port tool and the host tool cannot be used at the same time. Close any other applications that might be accessing the serial port.
• ドライバーの問題: Ensure that the drivers for your USB-to-serial converter (if used) are correctly installed and up-to-date.

7.2. Inaccurate or Intermittent Tracking

• 障害物： Ensure there are no significant physical obstructions (e.g., thick walls, large metal objects) between the module and the target area that could interfere with radar signals. While the module can detect through thin materials, dense objects will block signals.
• 取り付け位置: Adjust the module's mounting position and angle to ensure optimal coverage of the desired detection area, considering the specified Azimuth and Tilt angles.
• 環境干渉: While 24GHz is robust, strong electromagnetic interference in the immediate vicinity could potentially affect performance.

8. 保証情報

Specific warranty details for the JMT HLK-LD2450 module are not provided in the available product information. Please refer to the seller or manufacturer's official web保証条件については、こちらのサイトをご覧ください。

9. カスタマーサポート

For technical assistance, further documentation, or inquiries regarding the JMT HLK-LD2450 module, please contact your point of purchase or visit the official JMT website. Support contact information is not available in the provided product data.