User Manual: White-Rodgers Emerson 1F95-1277 Thermostat & F145-1328 Remote Sensor

導入

This manual provides comprehensive instructions for the installation, operation, and maintenance of your White-Rodgers Emerson 1F95-1277 Touchscreen 7-Day Programmable Thermostat and the Emerson Thermostats F145-1328 Indoor Remote Sensor. The 1F95-1277 thermostat features a large 12-inch touchscreen display for easy setup and programming, allowing for a different schedule each day of the week. It is compatible with most furnaces, air conditioners, and heat pump systems, including dual fuel systems. The F145-1328 remote sensor extends temperature monitoring capabilities, providing accurate readings up to 300 feet from the thermostat. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

安全情報

• Always turn off power to the heating and cooling system at the main fuse or circuit breaker panel before installing or servicing the thermostat or remote sensor.
• すべての配線接続が安全であり、地域の電気規則に準拠していることを確認してください。
• Do not short (jumper) across the electrical terminals on the gas valve or at the system circuit board to test the system. This will damage the thermostat and void the warranty.
• Use only specified battery types (Alkaline) for the thermostat. Replace batteries annually or when the low battery indicator appears.
• Keep the thermostat and sensor away from direct sunlight, heat sources, and drafts, as these can affect temperature readings.

パッケージ内容

インストールを開始する前に、すべてのコンポーネントが揃っていることを確認してください。

• White-Rodgers Emerson 1F95-1277 Touchscreen 7-Day Programmable Thermostat
• Emerson Thermostats F145-1328 Indoor Remote Sensor
• 取り付け金具（ネジ、壁アンカー）
• インストールガイド（このマニュアル）

セットアップとインストール

1. Thermostat Installation (1F95-1277)

1. 電源を切る： Turn off power to your heating and cooling system at the main fuse or circuit breaker panel.
2. 古いサーモスタットを取り外します。 Carefully remove your old thermostat from the wall. Take a picture of the wiring connections before disconnecting any wires. Label each wire with the terminal designation it was connected to.
3. サーモスタットベースの取り付け: Separate the new thermostat from its base. Position the base on the wall where the old thermostat was, ensuring it is level. Mark the mounting holes and drill pilot holes if necessary. Secure the base to the wall using the provided screws.
4. 結線： Connect the labeled wires to the corresponding terminals on the new thermostat base. Refer to the wiring diagram provided with your specific HVAC system if unsure.
5. サーモスタットを取り付ける: Align the thermostat body with the mounted base and snap it into place.
6. バッテリーの取り付け： Open the battery compartment and insert 2 AA alkaline batteries, observing polarity.

図1: 前面 view of the 1F95-1277 Thermostat display. This image highlights the large, easy-to-read touchscreen interface with current time, temperature, and system status.

Figure 2: The 1F95-1277 Thermostat installed on a wall. This image demonstrates the thermostat's appearance in a typical home environment, blending with interior decor.

2. Remote Sensor Installation (F145-1328)

The F145-1328 is a wired indoor remote sensor designed to provide temperature readings from a location other than the thermostat itself. This is useful for averaging temperatures across a larger area or monitoring a specific zone.

1. 場所を選択してください： Select a suitable location for the remote sensor. It should be placed on an interior wall, away from direct sunlight, drafts, heat sources, and areas with high humidity. The maximum recommended distance from the thermostat is 300 feet.
2. 配線： Run a low-voltage thermostat wire (typically 18-gauge, 2-conductor) from the thermostat's remote sensor terminals (usually labeled "S1" and "S2" or similar) to the F145-1328 sensor. Ensure the wires are securely connected to the terminals on both the thermostat and the sensor.
3. マウントセンサー： Mount the F145-1328 sensor to the wall using the provided mounting hardware. Ensure it is securely fastened.

Figure 3: The F145-1328 Indoor Remote Sensor. This image shows the compact design of the remote sensor, which is intended for discreet wall mounting.

Figure 4: Size comparison of the F145-1328 Remote Sensor. This image provides a visual reference for the sensor's physical dimensions, indicating its compact size.

3. 電源オンと初期設定

Once installation is complete, restore power to your HVAC system. The thermostat will power on and guide you through the initial setup process, which typically includes:

• 現在の時刻と曜日を設定します。
• Configuring system type (e.g., conventional, heat pump).
• Enabling or disabling the remote sensor.

操作手順

Thermostat Display and Controls

Figure 5: Thermostat display showing humidity. This image illustrates the thermostat's ability to display additional environmental data, such as humidity levels, alongside temperature.

The 1F95-1277 thermostat features a large touchscreen display with intuitive controls. Key areas and functions include:

• 現在の時刻/曜日: 現在の時刻と曜日を表示します。
• 現在の気温: Shows the ambient temperature detected by the thermostat or the active remote sensor.
• 設定温度: Indicates the desired temperature. Use the Up (▲） そして 下 (▼) arrows to adjust.
• システム モード: Tap "SYSTEM" to cycle through modes:
  • 熱： Activates heating when the temperature drops below the setpoint.
  • いいね： Activates cooling when the temperature rises above the setpoint.
  • 自動: 設定温度範囲を維持するために、加熱と冷房を自動的に切り替えます。
  • オフ： 暖房および冷房システムをオフにします。
• ファンモード： Tap "FAN" to cycle through modes:
  • 自動: ファンは、暖房または冷房システムがアクティブなときのみ作動します。
  • の上： Fan runs continuously, regardless of heating/cooling activity.
• メニュー： Accesses advanced settings, programming options, and system information.
• キーパッドのロックアウト： This feature prevents unauthorized changes to settings. Consult the full manual for instructions on enabling/disabling keypad lockout.

Programming a 7-Day Schedule

The 1F95-1277 allows for a unique program for each day of the week, with up to four time periods per day (e.g., Wake, Leave, Return, Sleep). Follow the on-screen prompts after entering the "Menu" and selecting "Program" or "Schedule".

1. を押す メニュー ボタン。
2. に移動 プログラム or スケジュール オプション。
3. プログラムする曜日を選択します。
4. Adjust the start time and desired temperature for each period (e.g., Wake, Leave, Return, Sleep).
5. Repeat for all desired days and periods.
6. プログラミング メニューを終了する前に変更を保存します。

Using the Remote Sensor (F145-1328)

If the F145-1328 remote sensor is enabled in the thermostat's settings, the thermostat will use its readings for temperature control. The thermostat display may indicate which sensor is currently active (internal or remote). This allows for more accurate temperature management in specific areas or for averaging temperatures across a larger space.

メンテナンス

• バッテリー交換: The thermostat is battery-powered. Replace the 2 AA alkaline batteries annually, or immediately when the low battery indicator appears on the display.
• クリーニング： Clean the thermostat and remote sensor surfaces with a soft, damp 布で拭いてください。研磨剤や溶剤は使用しないでください。
• 年次システムチェック: It is recommended to have your HVAC system professionally inspected and maintained annually to ensure optimal performance and efficiency.

トラブルシューティング

If you continue to experience issues, please refer to the contact information in the Support section or consult a qualified HVAC technician.

仕様

保証とサポート

For warranty information and technical support, please refer to the documentation included with your product or visit the official White-Rodgers / Emerson website. You may also contact their customer service directly for assistance with troubleshooting or product inquiries.

オンラインリソース: White-Rodgers Official Webサイト