ThreeH Vibration Sensor Alarm (Model H-HG07) Instruction Manual

導入

The ThreeH Vibration Sensor Alarm is a compact and effective security device designed to detect vibrations on doors, windows, and other entry points. Upon detecting significant vibration, it emits a loud 125dB alarm and activates an LED flash to deter intruders and alert occupants. Its slim design and adjustable sensitivity make it suitable for various applications in homes, offices, and personal belongings.

製品の特徴

簡単なインストール: No complex wiring or setup required. Simply attach the sensor to the desired surface.
調整可能な感度： Customize the vibration detection level to minimize false alarms.
多用途の保護: Suitable for doors, windows, apartments, offices, stores, garages, dormitory rooms, and RVs.
低バッテリー警告: 電池の交換が必要になると警告します。
大音量125dBアラーム： Deters intruders with a powerful siren and LED flash.

パッケージ内容

ThreeH Window Vibration Alarm (2 units for 2-pack)
ユーザーマニュアル
3 x LR44 Batteries (pre-installed in each alarm unit)

仕様

ブランド	スリーエイチ
モデル番号	H-HG07
アラーム音量	125デシベル
アラーム持続時間	30 seconds (stops automatically or when turned off)
電源	LR44電池3個（付属）
製品サイズ	7.2 x 0.95 cm / 2.83 x 0.37インチ
インストールタイプ	粘着式
接続技術	無線
推奨用途	Indoor/Outdoor (protected areas)

Diagram showing the dimensions of the ThreeH Vibration Sensor Alarm: 7.2 cm (2.83 inches) in length and 0.95 cm (0.37 inches) in thickness.

図1: Product Dimensions. The alarm measures 7.2 cm (2.83 inches) in length and 0.95 cm (0.37 inches) in thickness, highlighting its slim profile.

セットアップ手順

Follow these steps to install and activate your ThreeH Vibration Sensor Alarm:

表面を準備する: Ensure the surface where you intend to mount the alarm (e.g., door, window frame) is clean, dry, and smooth.
Peel Off Sticker: Carefully peel off the protective film from the adhesive backing on the rear of the alarm unit.
アラームを添付: Choose your desired position and firmly press the alarm onto the surface. Ensure it is securely attached.
オンにする： Locate the power switch on the side of the alarm and slide it to the "ON" position. A small LED indicator may briefly light up.
感度の調整: Use the sensitivity adjustment switch (often labeled High/Low or with a slider) to set the desired level of vibration detection. Start with a lower sensitivity and increase if needed.

Four-panel image illustrating the installation steps of the ThreeH Vibration Sensor Alarm. Panel 1 shows peeling off the adhesive backing. Panel 2 shows the alarm stuck to a door frame. Panel 3 shows a finger turning the 'ON' switch. Panel 4 shows a finger adjusting the sensitivity slider.

図2: Installation Steps. This image visually guides you through peeling the adhesive, attaching the alarm, turning it on, and adjusting sensitivity.

A white ThreeH Vibration Sensor Alarm is mounted on a light-colored door, with a small child sitting on the floor nearby. The alarm is positioned discreetly on the upper part of the door.

図3: Example Placement. The alarm is shown discreetly mounted on a door, demonstrating typical installation.

操作手順

Once installed and turned on, the ThreeH Vibration Sensor Alarm operates as follows:

武装: The alarm is armed when the power switch is in the "ON" position.
Triggering the Alarm: If the alarm detects significant vibration (e.g., from an attempted forced entry, window breaking), it will immediately activate.
アラーム応答: The alarm will emit a loud 125dB siren and an LED indicator light will flash simultaneously.
アラーム持続時間： The siren and LED flash will continue for approximately 30 seconds before automatically stopping.
武装解除: To stop the alarm before the 30-second cycle completes, slide the power switch to the "OFF" position.

An image depicting a person in a balaclava attempting to pry open a window with a crowbar. A white ThreeH Vibration Sensor Alarm is visible on the window frame, with red circles and lightning bolt icons indicating it is actively alarming.

図4: Alarm Activation Example. The alarm is shown detecting an attempted break-in through a window.

A person in a balaclava is seen peering through a partially open door. A black ThreeH Vibration Sensor Alarm is mounted on the door frame, with a red siren icon and sound waves indicating a loud 125dB alarm is active, designed to deter intruders.

図5: Intruder Deterrence. The alarm's loud sound is designed to scare away potential intruders.

メンテナンス

バッテリー交換: The alarm is powered by 3 x LR44 batteries. When the low battery warning activates (e.g., a specific LED pattern or weaker alarm sound), replace all three batteries. To replace, carefully open the battery compartment, remove old batteries, and insert new ones, ensuring correct polarity.
クリーニング： Wipe the alarm unit with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
接着チェック: Periodically check the adhesive to ensure the alarm remains securely attached to the surface. Re-apply if necessary.

トラブルシューティング

アラームが鳴らない:
- 電源スイッチが「オン」の位置にあることを確認してください。
- 電池を確認してください。電池残量が少ない場合や消耗している場合は交換してください。
- Verify the alarm is securely mounted and receiving sufficient vibration to trigger.
- Adjust the sensitivity to a higher setting.
誤報:
- Adjust the sensitivity to a lower setting.
- Ensure the mounting surface is stable and not subject to minor, unintentional vibrations (e.g., strong winds, passing heavy vehicles).
Alarm Sound is Weak:
- This typically indicates low batteries. Replace all three LR44 batteries.

保証情報

According to the product specifications, there is no applicable manufacturer warranty for this device. Please refer to the retailer's return policy for details on returns or exchanges.

サポート

For further assistance or inquiries regarding your ThreeH Vibration Sensor Alarm, please contact the retailer where the product was purchased. You may also visit the official ThreeH store page for additional product information and support resources.

ThreeH Store: https://www.amazon.ca/stores/ThreeH/page/2217C15A-8FAD-41DA-89A1-234D7750908C

ThreeH H-HG07