Shuttle XPC Slim DH610 Barebone PC Instruction Manual

1. はじめに

This manual provides essential instructions for the setup, operation, maintenance, and troubleshooting of your Shuttle XPC Slim DH610 Barebone PC. The DH610 is a compact and versatile barebone system designed to support Intel 12th and 13th Generation LGA1700 processors, offering robust performance for various applications including office, digital signage, and kiosks.

2. 安全情報

デバイスの損傷や怪我を防ぐために、以下の安全ガイドラインを読んで従ってください。

• Always disconnect the power cord before performing any installation or maintenance.
• Ensure the system is placed on a stable, flat surface with adequate ventilation.
• デバイスを湿気、極端な温度、直射日光にさらさないでください。
• Only use the power adapter provided or an approved equivalent.
• このマニュアルに記載されていない修理については、資格のあるサービス担当者にご相談ください。

3. パッケージ内容

パッケージにすべてのアイテムが含まれていることを確認します。

• Shuttle XPC Slim DH610 Barebone PC Unit
• VESAマウントキット
• 電源アダプターとコード
• Accessory Pack (screws, cables, etc.)
• クイックスタートガイド（付属している場合）

4. セットアップとインストール

The Shuttle DH610 is a barebone system, requiring the installation of a CPU, RAM, and storage devices before operation.

4.1. Opening the Chassis

Carefully remove the chassis cover to access the internal components. Typically, this involves unscrewing a few screws on the rear or sides of the unit and sliding the cover off.

Image: The Shuttle XPC Slim DH610 with its top cover removed, showing the internal layout including cooling fans and the motherboard.

4.2. CPUの取り付け

The DH610 supports Intel 12th/13th Generation Alder Lake-S LGA1700 processors with a maximum TDP of 65W. Ensure your chosen CPU has integrated graphics, as the system does not support F-series processors without integrated graphics or K-series processors.

1. CPUソケットレバーを開き、保護カバーを取り外します。
2. Carefully align the CPU with the socket, matching the triangular markers.
3. 無理に力を入れずに、CPU をソケットにゆっくりと差し込みます。
4. ソケットレバーを閉じてCPUを固定します。
5. 製造元の指示に従って CPU クーラーを取り付けます。

画像: 詳細な view of the Shuttle DH610 motherboard, highlighting the LGA1700 CPU socket, RAM slots, and other integrated circuits.

Note: For 13th Gen Intel Processors, BIOS Version DH610000.202 or newer is required. Update BIOS if necessary after initial setup with a 12th Gen CPU or via a compatible method.

4.3. RAMのインストール

The system features two 260-pin dual-channel DDR4 SODIMM slots, supporting up to 64GB (2x 32GB) at 3200MHz. Dual-channel memory is recommended for optimal performance.

1. Locate the SODIMM slots on the motherboard.
2. RAM モジュールのノッチをスロットのキーに合わせます。
3. Insert the module at a 45-degree angle and push down until the clips on both sides snap into place.

4.4. ストレージのインストール

The DH610 supports one 2.5-inch HDD/SSD and one M.2 2280 SSD.

1. 2.5" Drive: Mount the 2.5" HDD/SSD into the designated bay using the provided screws and connect the SATA data and power cables.
2. M.2 SSD: Insert the M.2 2280 SSD into its slot, securing it with the provided screw.

4.5. 周辺機器の接続

After installing internal components, reattach the chassis cover. Connect your peripherals to the available ports:

• 画面： Connect your monitor(s) to the HDMI 2.0b port or one of the two DisplayPort outputs. The system supports up to three 4K UHD displays.
• USB デバイス: Use the four USB 3.2 Gen1 ports (including one Type-C) and four USB 2.0 ports for keyboard, mouse, and other USB devices.
• ネットワーク： Connect to your network using either of the two Gigabit Ethernet LAN ports (Intel 2.5GbE + Intel 1GbE).
• シリアルデバイス: Utilize the two RS232 COM ports for compatible devices.
• オーディオ： Connect headphones or a microphone to the front audio jacks.

Image: The front panel of the Shuttle DH610, featuring the power button, USB 3.2 Gen1 ports (one Type-C), and audio input/output jacks.

Image: The rear panel of the Shuttle DH610, displaying the DC-IN power input, HDMI, two DisplayPort outputs, two LAN ports, USB ports, and two COM ports.

4.6. 電源接続

Connect the power adapter to the DC-IN port on the rear of the unit, then plug the power cord into an electrical outlet.

5. 操作手順

5.1.電源のオン/オフ

• 電源オン: フロントパネルにある電源ボタンを押します。
• 電源を切る： Perform a graceful shutdown through your operating system. Alternatively, press and hold the power button for 4-5 seconds for a forced shutdown (use only when necessary).

5.2. オペレーティング システムのインストール

The DH610 is compatible with Windows 11/10 (64-bit) and Linux (64-bit) operating systems. Follow the standard installation procedures for your chosen OS. Ensure all necessary drivers are installed for optimal performance, which can typically be found on the Shuttle support webサイト。

5.3. BIOS/UEFI アクセス

BIOS/UEFIセットアップユーティリティにアクセスするには、 消去 or F2 key repeatedly during system startup. This allows configuration of boot options, system settings, and hardware parameters.

6. メンテナンス

6.1. 清掃

Regularly clean the exterior of the unit with a soft, dry cloth. Use compressed air to clear dust from ventilation openings to ensure proper airflow and prevent overheating. Do not use liquid cleaners directly on the device.

6.2. BIOSアップデート

Periodically check the Shuttle website for BIOS updates. BIOS updates can improve system stability, add support for new hardware (like 13th Gen Intel CPUs), and fix bugs. Follow the instructions provided with the BIOS update package carefully.

7。 トラブルシューティング

DH610 で問題が発生した場合は、次の一般的な問題と解決策を参照してください。

• ディスプレイ出力なし:
  • Ensure the monitor is powered on and correctly connected to the HDMI or DisplayPort.
  • Verify that the CPU has integrated graphics and that the display cable is connected to the motherboard's video output, not a discrete graphics card (if applicable).
  • 別のディスプレイ ケーブルまたはモニターを試してください。
• システムが電源オンにならない:
  • Check that the power adapter is securely connected to both the unit and the electrical outlet.
  • Ensure the CPU and RAM are correctly installed and seated.
  • 別のデバイスで電源コンセントをテストします。
• 13th Gen CPU Not Recognized:
  • The system requires BIOS Version DH610000.202 or newer for 13th Gen Intel processors. If you have an older BIOS, you may need to install a 12th Gen CPU first to update the BIOS.
• システムの過熱:
  • Ensure the chassis ventilation holes are not obstructed.
  • Clean any dust accumulation from the internal fans and heatsinks.
  • CPU クーラーが正しく取り付けられており、CPU としっかりと接触していることを確認します。

8. 仕様

9. 保証とサポート

9.1. 製造元の保証

The Shuttle XPC Slim DH610 Barebone PC comes with a 3-Year Manufacturer's Warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

9.2. テクニカルサポート

For technical assistance, driver downloads, BIOS updates, or further troubleshooting not covered in this manual, please visit the official Shuttle website or contact Shuttle customer support. Free lifetime technical support is typically provided by the manufacturer.

詳細については、以下をご覧ください。 www.shuttle.com