1. はじめに
This manual provides essential information for the proper setup, operation, and maintenance of your LDARC X-BOSS FM900 2.4GHz FASST Receiver. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2.製品オーバーview
Image: The LDARC X-BOSS FM900 receiver, a compact circuit board featuring surface-mount components, an integrated antenna, and clearly labeled 'FM900' branding. This image illustrates the physical design and component layout of the receiver.
3. 特徴
- Offers great reliability, stable signal link, precision antenna, and high sensitivity.
- Compact and lightweight design for various applications.
- Integrated LNA (Low Noise Amplifier) for enhanced signal reception.
- RSSI (Received Signal Strength Indicator) output for real-time signal monitoring.
4. 仕様
| 仕様 | 詳細 |
|---|---|
| アイテム | FM900 Receiver |
| 重さ | 1.2グラム |
| 寸法 | 11.5mm×21mm |
| 巻tage | 4-6V |
| 作業範囲 | >900m (air distance without electromagnetic interference) |
| プロトコル | 速い |
| 出力1 | エルエヌエー |
| 出力2 | RSSI |
| サポートされている送信機 | T8FG, T14SG, T16SZ, T18SZ, T18MZ, T32MZ TX |
| Real-Time RSSI Compatibility | F3, F4, F7, etc. flight controllers |
5. パッケージ内容
- 1x LDARC X-BOSS FM900 Receiver
6. セットアップ
6.1. インストール
Carefully connect the receiver to your flight controller or power source, ensuring correct polarity and signal connections. Mount the receiver securely in your model, away from sources of electrical interference. Position the antenna for optimal signal reception, avoiding obstructions.
6.2. 製本手順
To establish communication between your transmitter and the FM900 receiver, follow these general binding steps:
- Power on your transmitter and select the FASST protocol.
- Place your transmitter in binding mode (refer to your transmitter's manual for specific instructions).
- Apply power to the FM900 receiver. The receiver's LED indicator should begin to flash, indicating it is ready for binding.
- Once the binding process is complete, the receiver's LED will typically turn solid green, indicating a successful connection.
- Power cycle both the transmitter and receiver to confirm the binding is retained.
7. 操作手順
After successful binding and installation, ensure your transmitter and receiver are powered on before operating your model. Always perform a range check and verify all control surfaces respond correctly before flight. Monitor the RSSI output on your flight controller or OSD (On-Screen Display) to ensure a strong signal link during operation.
8. メンテナンス
- 受信機を清潔に保ち、ほこり、汚れ、湿気を避けてください。
- Regularly inspect antenna connections for damage or loose contacts.
- 受信機を極端な温度や直射日光に長時間さらさないでください。
- Ensure proper ventilation around the receiver during operation.
9。 トラブルシューティング
- No Signal/Loss of Link: Re-check binding procedure. Ensure transmitter and receiver are powered on. Verify antenna connection and placement. Check for potential interference sources.
- 断続的な信号: Inspect antenna for damage. Ensure receiver is not too close to high-current wires or other electronic components that may cause interference.
- 受信機の電源が入らない: 電源接続とボリュームを確認してくださいtage supply (4-6V). Check for shorts or incorrect wiring.
- 不正な制御応答: Confirm correct channel mapping in your flight controller or model setup. Re-bind the receiver if necessary.
10. 保証およびサポート情報
LDARC products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please reach out to your authorized LDARC dealer or visit the official LDARC webサポートサイト。