Voktta PWM DC Motor Speed Controller (Model VKXN0029) - Instruction Manual

導入

This manual provides comprehensive instructions for the Voktta PWM DC Motor Speed Controller, Model VKXN0029. This device is designed to regulate the speed of DC motors by adjusting the Pulse Width Modulation (PWM) signal. It is suitable for DC motors operating within a voltage range of 9V to 60V and a maximum power output of 500W. Key features include soft start protection, a digital encoder knob for precise control, and adjustable duty cycle and frequency settings.

製品を安全かつ効率的に使用するために、設置および操作の前にこのマニュアルをよくお読みください。

安全情報

• 電源のボリュームを確認してくださいtage is within the specified range (DC 9V-60V) to prevent damage to the controller and motor.
• 配線の接続または切断を行う前に必ず電源を切ってください。
• Observe correct polarity when connecting the power supply and motor. Reverse polarity can cause irreversible damage.
• Do not exceed the maximum rated current of 20A or maximum power of 500W.
• デバイスを湿気、ほこり、極端な温度から遠ざけてください。
• This product is intended for industrial and hobbyist use. Professional installation is recommended if you are unfamiliar with electrical wiring.

製品終了view

The Voktta PWM DC Motor Speed Controller features a compact design with a digital display and an encoder knob for user interaction. The unit's dimensions are 79mm x 43mm x 26mm.

図1: 前面 view of the Voktta PWM DC Motor Speed Controller.

Figure 2: Dimensions of the Voktta PWM DC Motor Speed Controller (79mm x 43mm x 26mm).

主要コンポーネント:

Figure 3: Front panel with labeled controls and display.

• Digital Display (Nixie tube): Shows the motor adjustment duty cycle, and allows setting upper/lower limits and frequency.
• ロータリーエンコーダーノブ: Used to adjust motor speed. Turning left decreases the duty cycle, turning right increases it.
• エンコーダーボタン: A short press controls motor start and stop. A long press enters the setting mode for parameters.
• Motor Start/Stop Light: Indicates motor status (light on for start, off for stop).

セットアップとインストール

Proper wiring is crucial for the safe and correct operation of the speed controller. Refer to the wiring diagram below.

Figure 4: Wiring diagram for the Voktta PWM DC Motor Speed Controller.

配線手順：

1. 電源入力: Connect your DC power supply (9V-60V) to the "POWER+" and "POWER-" terminals. Ensure correct polarity.
2. モーター出力： Connect your DC motor to the "MOTOR+" and "MOTOR-" terminals. The motor's rotation direction can be reversed by swapping these connections.
3. 外部制御（オプション）: The unit can be connected to a switch signal or a 3.3V level signal via the J3 terminals (STOP, GND, CTRL) to control motor start and stop.
4. 取り付け: The controller is designed for panel mounting. Ensure adequate ventilation around the unit.

Warning: Double-check all connections before applying power to prevent damage.

操作手順

1. 電源のオン/オフ

• After wiring, apply power to the controller. The digital display will light up.
• To start the motor, short press the rotary encoder knob. The motor start light will illuminate.
• To stop the motor, short press the rotary encoder knob again. The motor start light will turn off.

2. モーター速度の調整

• With the motor running, turn the rotary encoder knob clockwise to increase the motor speed (increase duty cycle).
• Turn the rotary encoder knob counter-clockwise to decrease the motor speed (decrease duty cycle).
• The digital display shows the current duty cycle percentage.

3. Parameter Settings (Advanced)

To enter the parameter setting mode, long press the rotary encoder knob until the display changes.

1. Setting Duty Cycle Limits:
   • In setting mode, rotate the knob to select the parameter for minimum duty cycle (e.g., 'L00' for 0%). Press the knob to confirm.
   • Rotate the knob to adjust the value. Press again to save and move to the next parameter.
   • Repeat for maximum duty cycle (e.g., 'H100' for 100%).
2. Setting PWM Output Frequency:
   • In setting mode, rotate the knob to select the frequency parameter (e.g., 'F20' for 20 KHz). Press the knob to confirm.
   • Rotate the knob to adjust the frequency (1 KHz to 99 KHz). The default frequency is 20 KHz. Press again to save.
3. 設定モードを終了しています: ロータリーエンコーダノブをもう一度長押しすると、設定モードが終了し、通常の操作に戻ります。

The soft start protection feature automatically reduces the initial current surge, protecting the motor and extending its lifespan.

仕様

メンテナンス

• コントローラーは清潔に保ち、ほこりやゴミが付かないようにしてください。清掃には柔らかく乾いた布をご使用ください。
• すべての配線接続が安全で腐食がないことを定期的に確認してください。
• Avoid exposing the device to direct sunlight or high humidity for extended periods.
• cを開こうとしないでくださいasing or modify the internal circuitry, as this will void any warranty and may cause damage or injury.

トラブルシューティング

保証とサポート

Voktta products are manufactured to high-quality standards. For any questions, technical support, or warranty inquiries, please contact your retailer or the manufacturer directly. Please refer to your purchase documentation for specific warranty terms and contact information.