導入
This instruction manual details the proper procedure for using the Toro Genuine OEM Hydraulic Oil Change Kit. This kit is designed to facilitate the replacement of hydraulic oil and filters in compatible lawn mowers and equipment, ensuring optimal performance and longevity of your hydraulic system. Please read all instructions carefully before beginning any maintenance.
安全上の注意
Always prioritize safety when performing maintenance. Failure to follow these precautions may result in injury or damage to equipment.
- Ensure the equipment is turned off, the engine is cool, and the spark plug wire is disconnected before starting any work.
- 安全メガネや手袋などの適切な個人用保護具 (PPE) を着用してください。
- 換気の良い場所で作業してください。
- 使用済みのオイルとフィルターは、地域の規制に従って責任を持って廃棄してください。
- Refer to your equipment's specific owner's manual for additional safety guidelines and hydraulic system capacity.
キット構成
The Toro Hydraulic Oil Change Kit includes the following genuine components:
- 2x Toro 144-6603 (HG71943) Hydro Oil Filters
- 10 Quarts of Toro Hypr-Oil 500 Hydraulic Oil
Image: Toro Hypr-Oil 500 Hydraulic Oil, 1-quart bottle. The kit includes 10 quarts of this oil.
画像: 上 view of a Toro 144-6603 (HG71943) Hydro Oil Filter. The kit contains two such filters.
画像: 下 view of a Toro 144-6603 (HG71943) Hydro Oil Filter, showing the filter media and date stamp.
Preparation for Oil Change
- 機器を平らな場所に駐車してください。
- Ensure the engine is off and cool to the touch. Disconnect the spark plug wire to prevent accidental starting.
- Gather necessary tools: drain pan, wrench for filters, rags, and funnels.
- Locate the hydraulic oil reservoir and filters on your specific equipment model. Refer to your equipment's owner's manual for exact locations and capacities.
Hydraulic Oil and Filter Replacement Procedure
Follow these steps to replace the hydraulic oil and filters:
- Drain Old Hydraulic Oil: Place a suitable drain pan under the hydraulic system's drain plug. Remove the drain plug and allow all old hydraulic oil to drain completely. This may take some time.
- 古いフィルターを削除する: Using a filter wrench, carefully loosen and remove the old hydraulic oil filters. Be prepared for some oil to spill.
- 新しいフィルターを準備する: Apply a thin film of new Toro Hypr-Oil 500 to the rubber gasket of each new filter. This ensures a proper seal.
- 新しいフィルターをインストールします: Thread the new filters onto their respective mounts by hand until the gasket makes contact with the mounting surface. Then, tighten an additional 1/2 to 3/4 turn. Do not overtighten.
- 排水プラグの交換: Once all old oil has drained, clean the drain plug and reinstall it securely.
- Refill with New Hydraulic Oil: Locate the hydraulic oil fill cap. Using a clean funnel, slowly add the new Toro Hypr-Oil 500 to the reservoir. Refer to your equipment's owner's manual for the exact capacity. Do not overfill.
- 液面レベルを確認する: After filling, start the engine and operate the hydraulic system briefly (e.g., engage the mower deck, move control levers) to circulate the oil. Turn off the engine, wait a few minutes, and recheck the fluid level. Add more oil if necessary to reach the recommended level.
- 漏れの検査: Visually inspect all connections and filters for any signs of leaks.
- 使用済み材料の廃棄: Properly dispose of the used oil and filters at an authorized recycling center.
トラブルシューティング
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Hydraulic System Not Operating Correctly After Oil Change | Low fluid level, air in the system, incorrect oil type, or improperly installed filters. | Check fluid level and add if low. Bleed air from the system (refer to equipment manual). Ensure correct oil (Toro Hypr-Oil 500) was used. Recheck filter installation. |
| Oil Leak Around Filters | Filter not tightened sufficiently, overtightened filter, damaged gasket, or debris on mounting surface. | Ensure filters are tightened correctly (hand-tight plus 1/2 to 3/4 turn). Inspect gasket for damage and mounting surface for cleanliness. Replace filter if gasket is damaged. |
| Oil Leak from Drain Plug | Drain plug not tightened, damaged O-ring/gasket on drain plug. | Tighten drain plug securely. Inspect and replace O-ring or gasket if damaged. |
製品仕様
- ブランド： トロ
- メーカー部品番号: 144-6603 (Filter), 114-4713 (Oil)
- 含まれるコンポーネント: 2x 144-6603 (HG71943) Filters, 10 Quarts of Hypr-Oil 500
- オイル粘度: 10W-30 sae_grade
- 液体量: 10 Quarts total
- 互換性あり: Toro Z-Master 4000 (52in, 60in, 72in models 74010, 74015, 74020, 74022), Bad Boy Mowers with ZT4400 Transaxles, Ferris F210Z, F320Z, IS2100Z, IS3200Z with ZT5400 Transaxles, Gravely units with ZT-5400 Transaxles (models 992184, 992185, etc.), Scag Cheetah Series Mowers with ZT-5400 Transaxles.
- 互換性に関する注意： Kit is compatible with Hydro-Gear Kit 72881.
保証情報
For specific warranty details regarding the Toro Hydraulic Oil Change Kit components, please refer to the official Toro manufacturer's warranty documentation provided with your original equipment or visit the official Toro website. This kit contains genuine OEM parts, which typically fall under the manufacturer's standard warranty for replacement parts.
カスタマーサポート
If you have questions or require assistance with the Toro Hydraulic Oil Change Kit, please contact Toro customer support or an authorized Toro service dealer. You can typically find contact information on the official Toro website or in your equipment's owner's manual.
トロ公式 Webサイト： www.toro.com