VICTGOAL Adult Bike Helmet

導入

This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your VICTGOAL Adult Bike Helmet. Please read this manual thoroughly before using the helmet to ensure safety and optimal performance.

Figure 1: VICTGOAL Adult Bike Helmet (Blue, XL size shown)

製品の特徴

• 磁気ゴーグルとサンバイザー: Equipped with a detachable magnetic visor and goggles for eye protection against sunlight, sand, and wind. Designed to accommodate prescription glasses.
• 耐衝撃性 Constructed with a high-density PC (Polycarbonate) shell and EPS (Expanded Polystyrene) foam to absorb impact and provide protection during cycling.
• 一体型リアライト: Features a bright rear light with three flashing modes (steady, slow flashing, fast flashing) for enhanced visibility during night cycling.
• Adjustable Sizing System: Designed for adult men and women, available in M, L, and XL sizes. The helmet includes an easy-to-adjust dial for a secure and comfortable fit.
• Ventilation and Lightweight Design: Incorporates 21 breathable vents to promote airflow, keeping the rider cool and dry. The helmet weighs approximately 310g (0.68 lb) to minimize head burden.

Figure 2: Helmet wearing modes (visor and goggles)

Figure 3: Ventilation and reflective strap details

Figure 4: Helmet construction showing EPS foam for impact absorption

安全情報

The VICTGOAL Adult Bike Helmet is designed to reduce the risk of head injury during cycling. For maximum protection, ensure the helmet is properly fitted and secured according to the instructions below. This helmet is not intended for motor sports or other activities not specified.

• サイクリング時は必ずヘルメットを着用してください。
• Ensure the helmet fits snugly and does not move freely on your head.
• Inspect the helmet for any damage before each use. Do not use a damaged helmet.
• Replace the helmet after any significant impact, even if visible damage is not apparent.
• Do not modify the helmet or use accessories not approved by the manufacturer.

セットアップとフィッティング

1. Sizing and Fit Adjustment

Proper fit is crucial for helmet effectiveness. Measure your head circumference to select the correct size. The helmet should sit level on your head, covering your forehead, and the straps should be snug but comfortable.

• 頭囲を測ります: Use a flexible tape measure to find the circumference of your head, approximately 0.6 inches (1.5 cm) above your ears and across your forehead.
• サイズを選択: Refer to the sizing chart below. If your measurement falls between two sizes, choose the larger size for a more comfortable fit.
• 保持システムを調整する: Place the helmet on your head. Turn the adjustment dial at the back of the helmet clockwise to tighten the fit until it is snug and stable, but not uncomfortably tight. Turn counter-clockwise to loosen.
• ストラップの調整: The side straps should form a 'V' shape just below your ears. Adjust the strap sliders to achieve this. The chin strap should be tightened so that only one or two fingers can fit between the strap and your chin.
• フィット感を確認: With the chin strap fastened, try to move the helmet from side to side and front to back. It should not shift significantly.

Figure 5: Sizing Guide - M (54-58 cm)

Figure 6: Sizing Guide - L (57-61 cm)

Figure 7: Sizing Guide - XL (59-63 cm)

2. Attaching/Detaching Visor and Goggles

The helmet comes with a detachable sun visor and magnetic goggles. Both attach securely to the helmet.

• サンバイザー: Align the three clips on the sun visor with the corresponding slots on the front of the helmet. Press firmly until they click into place. To detach, gently pull the visor away from the helmet.
• Magnetic Goggles: The goggles attach to the helmet via strong magnets located on the helmet's front edge. Simply bring the goggles close to the magnetic points, and they will snap into position. To remove, gently pull them away. The goggles can be flipped upwards and attached to the helmet when not in use.

3. Rear Light Activation

The integrated rear light is powered by a CR2032 battery (included). It may require activation or battery installation upon first use.

• Locate the rear light unit at the back of the helmet's adjustment dial.
• Press the center of the light unit to cycle through the modes: Steady On, Slow Flashing, Fast Flashing, and Off.
• Ensure the light is functioning before night rides.

Figure 8: Rear light features and battery life

手術

Once the helmet is properly fitted, its operation is straightforward.

• ヘルメットの着用: Always ensure the helmet is worn level on your head, covering your forehead, and the chin strap is securely fastened.
• Using Goggles/Visor: Attach the magnetic goggles or sun visor as needed for eye and face protection. The goggles can be easily flipped up or removed when not required.
• Operating Rear Light: Press the button on the rear light to turn it on and cycle through the three illumination modes (steady, slow flash, fast flash) to suit visibility conditions.

メンテナンス

Regular maintenance will prolong the life of your helmet and ensure its continued effectiveness.

1. ヘルメットの掃除

• シェル： Clean the helmet's exterior with a soft cloth, mild soap, and water. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the helmet's materials.
• Internal Pads: The internal padding is soft and washable. Detach the pads from the helmet (they are typically attached with hook-and-loop fasteners). Hand wash them with mild soap and water, then air dry completely before reattaching.
• Goggles/Visor: Clean the goggles and visor with a soft, lint-free cloth and water. Do not use paper towels or harsh chemicals, which can scratch the lens.

Figure 9: Detachable and washable helmet liner

2. Battery Replacement for Rear Light

The rear light uses one CR2032 3V battery. Replace the battery when the light dims or stops functioning.

Figure 10: Battery Replacement Guide

1. Open the pad covering the rear light unit.
2. Carefully remove the taillight unit from its housing.
3. Disassemble the back cover of the light unit, typically by unscrewing small screws or prying open clips.
4. 回路基板を取り外します。
5. Remove the old CR2032 battery and insert a new CR2032 battery with the positive (+) side facing up.
6. Reassemble the light unit and reinsert it into the helmet.

トラブルシューティング

仕様

保証とサポート

For product support, inquiries, or warranty claims, please contact the manufacturer, VICTGOAL, directly. Refer to your purchase documentation for specific return policies, which typically allow for returns or replacements within 30 days of purchase.

この商品の公式販売者のビデオは見つかりませんでした。