GalaxyElec PM02 V3 Power Module Instruction Manual

1. はじめに

The GalaxyElec PM02 V3 Power Module is designed to provide a clean power supply to your flight controller and associated accessories, while also offering accurate current consumption and battery voltage measurements. This module is compatible with various flight controllers including APM, Pix32, Pixhawk 4, Pixhawk 4 Mini, and Durandal. It features an integrated switching regulator to deliver stable 5.2V power.

2.製品オーバーview

2.1 主な特徴

• 最大入力ボリュームtage: 60V
• Max Current Sensing: 120A
• 巻tage および電流測定: Configured for 5V ADC
• Switching Regulator Output: 5.2V at 3A maximum
• 接続性: 6-position Molex cable for APM/Pix32 'PM' connector; 6-position GH cable for Pixhawk4/Pixhawk4 mini/Durandal 'PM' connector
• Provides clean power from a LiPo battery.
• Measures current consumption and battery voltage.
• Comes pre-assembled with XT60 connectors and protective shrink tubing.

2.2 パッケージ内容

• 1x PM02 V3 Power Module with XT60 Connectors
• 1x Molex 6 Position Connector Cable (15 cm)
• 1x GH 6 Position Connector Cable (15 cm)

3. 仕様

4.セットアップガイド

4.1 Connecting the Power Module

1. Connect to LiPo Battery: Connect your LiPo battery (up to 12S) to the XT60 input connector on the PM02 V3 module. Ensure correct polarity.
2. Connect to Flight Controller:
   • For APM and Pix32 flight controllers, use the provided 6-position Molex cable to connect the module to the 'PM' connector on your flight controller.
   • For Pixhawk 4, Pixhawk 4 Mini, and Durandal flight controllers, use the provided 6-position GH cable to connect the module to the 'PM' connector on your flight controller.
3. 電源アクセサリ: The PM02 V3 is designed to power the flight controller, an RC receiver, and accessories such as GPS or radio modules. It provides a regulated 5.2V at up to 3A.

重要な注意: The PM02 V3 Power Module is ない designed to power servos. For servo power, use your aircraft's dedicated ESC/BEC (Electronic Speed Controller/Battery Eliminator Circuit).

Image: The PM02 V3 Power Module showing the XT60 connectors for battery input/output and the two signal cables (Molex and GH) for connecting to different flight controllers.

5. 操作手順

Once correctly connected, the PM02 V3 Power Module will automatically provide power to your flight controller and begin transmitting voltage and current data. This data is crucial for battery monitoring and flight controller telemetry.

• 電力供給： The module converts the LiPo battery voltage to a stable 5.2V for your flight controller and compatible accessories.
• テレメトリー： The module continuously measures the battery's voltage and the current being drawn by the system. This information is sent to the flight controller via the connected signal cable (Molex or GH) and can be displayed in your ground station software.
• 較正： 正確な音量を得るにはtage and current readings, it is recommended to perform a power module calibration within your flight controller's ground station software (e.g., Mission Planner, QGroundControl) after initial setup. Refer to your flight controller's specific documentation for calibration procedures.

画像: 上 view of the PM02 V3 Power Module, showing the main circuit board and XT60 connectors.

6. メンテナンス

The PM02 V3 Power Module is designed for durability, but proper care ensures longevity and reliable performance.

• 接続を検査する: Regularly check all cable connections (XT60, Molex, GH) to ensure they are secure and free from corrosion or damage.
• 目視検査: Periodically inspect the module and its wiring for any signs of physical damage, such as frayed wires, cracked shrink tubing, or burnt components.
• 清潔に保ちます： モジュールにほこり、汚れ、湿気がないことを確認してください。必要に応じて、柔らかく乾いたブラシまたは圧縮空気を使用して清掃してください。
• ストレージ： Store the module in a dry, cool environment away from direct sunlight and extreme temperatures when not in use.

画像: 詳細トップ view of the PM02 V3 circuit board, showing components and wiring connections.

7。 トラブルシューティング

If you encounter issues with your PM02 V3 Power Module, consider the following troubleshooting steps:

• フライトコントローラーに電源が供給されていません:
  • Verify that the LiPo battery is charged and correctly connected to the XT60 input.
  • Check all connections between the power module and the flight controller (Molex or GH cable) for proper seating and continuity.
  • Inspect the power module and cables for any visible damage.
• 間違った巻tage/現在の読書:
  • Ensure the power module is correctly calibrated in your flight controller's ground station software. Refer to your flight controller's manual for specific calibration steps.
  • Confirm that the correct power module type is selected in your flight controller's settings, if applicable.
• モジュールの過熱:
  • Ensure the current draw from your flight controller and accessories does not exceed the module's 3A output limit.
  • Verify that no servos are being powered directly by the module, as this can cause overload.

画像: 下 view of the PM02 V3 Power Module, clearly showing the 'Holybro PM02 V3.0' branding.

8. 安全情報

Always observe the following safety precautions when handling and operating the PM02 V3 Power Module:

• 正しい極性: Always ensure correct polarity when connecting the LiPo battery to the power module. Incorrect polarity can cause severe damage to the module and connected components.
• 巻tage制限： 最大入力容量を超えないでくださいtag60Vのe。
• 現在の制限: Do not exceed the maximum current sensing of 120A or the 3A output limit for the regulated 5.2V supply.
• 短絡: Avoid short circuits at all times. Ensure all connections are insulated and secure.
• LiPo Battery Handling: Exercise caution when handling LiPo batteries. They can be dangerous if mishandled.
• 専門家による設置: If you are unsure about any installation steps, seek assistance from an experienced professional.

9. 保証とサポート

For warranty information, please refer to the terms and conditions provided by your retailer at the time of purchase. For technical support or further inquiries, please contact the manufacturer or your authorized dealer.

保証請求に備えて購入証明書を保管してください。