1. はじめに
This manual provides detailed instructions for the safe and effective use of the OONO DPST 1NO 1NC 8Amp Power Relay Module, Model F-1022 Series (AC/DC 5V). This module is designed to provide a reliable switching solution for various electrical applications, converting an input control signal into a double-pole, single-throw (DPST) output switch with both Normally Open (NO) and Normally Closed (NC) contacts.
2. 安全情報
警告: 感電の危険
- Always disconnect power before installing, wiring, or performing any maintenance on the relay module.
- すべての配線が資格を持った電気技師によって行われ、地域および国の電気規則に準拠していることを確認してください。
- 指定された容量を超えないでくださいtage and current ratings of the module.
- モジュールを湿気、極端な温度、腐食性の環境にさらさないでください。
- DC 接続の極性が正しいことを確認します。
3.製品オーバーview
The OONO F-1022 Series relay module features a compact design with pre-wired connections for ease of installation. It includes an LED indicator for relay status and provides both Normally Open (NO) and Normally Closed (NC) contacts for versatile applications.
図3.1: 前面 view of the OONO F-1022 Series relay module, showing the input (GRN, BLU) and output (C1, NO1, C2, NC2) terminals, along with the LED indicator and basic wiring diagram.
Figure 3.2: Angled perspective of the relay module, highlighting the pre-attached input (green and blue) and output (red and black) wires for direct connection.
図3.3: 別の角度から view, displaying the label with various control voltage options for the F-1022 Series, including AC/DC 5V, 12V, 24V, 48V, AC 115V, and AC 230V.
Figure 3.4: Technical drawing providing precise dimensions of the relay module in millimeters, useful for mounting and integration into enclosures.
4. 仕様
| 特徴 | 説明 |
|---|---|
| モデル番号 | F-1022シリーズ |
| 入力制御信号 | AC/DC 5V (Current: 80mA) |
| Output Switch Type | DPST 1NO 1NC (Double Pole Single Throw, 1x Normally Open and 1x Normally Closed) |
| Rated Current (Output) | 8A / 250VAC or 8A / 30VDC (per switch) |
| 連絡先 | 銀 |
| 取り付けタイプ | Screw Mount (Two screw mounting holes provided) |
| インジケータ | LED for relay action status |
| 寸法 | 3.7 x 2.2 x 1.3インチ（約94 x 56 x 33 mm） |
| 重さ | 3.21オンス（約91グラム） |
5. セットアップとインストール
Follow these steps for proper installation of the relay module:
- 電源切断: Ensure all power sources to the circuit where the relay will be installed are completely disconnected and locked out.
- 取り付け: Secure the relay module using the two screw mounting holes provided on the housing. It can be fixed to a wall or wooden board.
- 入力配線: Connect the control signal wires to the input terminals of the module. For the AC/DC 5V model, connect your 5V AC or DC control signal to the green (GRN) and blue (BLU) input wires. The module requires approximately 80mA for activation.
- 出力配線: The module provides DPST (Double Pole Single Throw) output contacts. There are two independent switches, SW1 and SW2.
- SW1 (Common C1, Normally Open NO1): When the input signal is applied, the contact between C1 and NO1 closes.
- SW2 (Common C2, Normally Closed NC2): When the input signal is applied, the contact between C2 and NC2 opens.
- 検証： 電源を復旧する前に、すべての配線接続の正確性と安全性を再確認してください。
6. 操作手順
The OONO F-1022 Series relay module operates based on the presence or absence of the input control signal.
- No Input Signal (LED OFF): In the absence of an input control signal, the relay is de-energized. In this state:
- Switch 1 (SW1) is OFF (C1 and NO1 are open).
- Switch 2 (SW2) is ON (C2 and NC2 are closed).
- Input Signal Applied (LED ON): When the AC/DC 5V control signal is applied to the input wires, the relay energizes. In this state:
- Switch 1 (SW1) is ON (C1 and NO1 are closed).
- Switch 2 (SW2) is OFF (C2 and NC2 are open).
- LEDインジケーター: The red LED on the module illuminates when the input control signal is present and the relay is energized, providing a visual indication of its operational status.
7. メンテナンス
The OONO F-1022 Series relay module is designed for long-term, reliable operation with minimal maintenance. However, periodic checks are recommended:
- 目視検査: モジュールに物理的な損傷、変色、接続の緩みなどの兆候がないか定期的に検査してください。
- クリーニング： If necessary, gently clean the exterior of the module with a dry, soft cloth. Do not use solvents or abrasive cleaners.
- 接続の整合性: Ensure all wire connections remain secure and free from corrosion.
8。 トラブルシューティング
If you encounter issues with your OONO F-1022 Series relay module, consider the following:
- Relay Not Activating (LED Off):
- Verify that the input control signal (AC/DC 5V) is present and stable.
- Check the input wiring for correct connections and continuity.
- Ensure the input current is sufficient (80mA).
- 負荷が切り替わらない:
- Confirm the relay LED is illuminating when the input signal is applied. If not, troubleshoot the input signal as above.
- Check the output wiring for correct connections to C1/NO1 or C2/NC2.
- Verify the load circuit is functioning correctly and not drawing excessive current beyond the 8A rating.
- 負荷容量を確認するtage is within the module's rated limits (250VAC or 30VDC).
- 断続動作:
- 入力端子と出力端子の両方で配線接続が緩んでいないか確認してください。
- Ensure the input control signal is stable and free from voltage fluctuations or noise.
- Verify the operating environment is within acceptable temperature and humidity ranges.
9. 保証とサポート
For warranty information and technical support, please refer to the product packaging or contact your point of purchase. Specific warranty terms and support channels may vary depending on your region and retailer.