1.製品オーバーview
The SharkBite 1/2 Inch Straight Stop x 1/2 Inch NPSM Click Seal Faucet Connector is a versatile plumbing fitting designed to simplify water supply connections to faucets. It features a push-to-connect mechanism for quick and secure installation without the need for special tools, glue, crimping, or soldering. This connector is suitable for use with PEX, CPVC, PE-RT, SDR-9 HDPE, and copper pipes, making it ideal for various plumbing projects.
主な特徴:
- Push-to-Connect Mechanism: Ensures a watertight and leak-free connection.
- Click Seal Faucet Connector: Allows for hand tightening and provides an audible click when a secure connection is made.
- 多彩な互換性: Works with PEX, CPVC, PE-RT, SDR-9 HDPE, and copper pipes.
- 簡単なインストール: No special tools, crimping, glue, or soldering required. Can be installed in wet lines.
- 統合設計: Features a 1/2-inch push-fit stop valve and a flexible hose for faster installation.
2. 安全情報
Always prioritize safety when working with plumbing. Read and understand all instructions before beginning installation. If you are unsure about any step, consult a qualified plumber.
- 配管作業を始める前に、主給水を停止してください。
- 安全メガネや手袋などの適切な個人用保護具を着用してください。
- 作業エリアが十分に明るく、障害物がないことを確認してください。
- Verify that the pipe ends are clean, free of scratches, and deburred before insertion.
- Do not overtighten connections, especially the Click Seal nut, as it is designed for hand tightening.
3. セットアップとインストール
This section provides detailed instructions for installing your SharkBite Faucet Connector. Ensure you have all necessary components and tools before proceeding.
3.1. Components and Compatibility
The SharkBite Faucet Connector is designed for use with 1/2 inch CTS (Copper Tube Size) pipes. It is compatible with PEX, CPVC, PE-RT, SDR-9 HDPE, and copper pipes.
3.2. インストール手順
- パイプを準備する: Ensure the pipe end is cut cleanly and squarely. For copper pipes, remove any sharp edges or burrs. The pipe should be free of scratches and debris. Leave a minimum of 1 inch of pipe exposed for insertion.
- Determine Stub-out Type: Identify if your water supply stub-out comes out of the wall (requires an angle stop valve) or out of the floor (requires a straight stop valve). This product is a straight stop valve.
- Mark Insertion Depth: Use a SharkBite depth and deburr tool (or refer to the insertion depth chart on SharkBite.com) to measure and mark the correct insertion depth on your pipe stub-out. For 1/2 inch CTS pipe, the insertion depth is approximately 15/16 inches (0.95 inches).
- Install the Stop Valve: Push the straight stop valve onto the pipe stub-out until it reaches the insertion mark you made. Ensure a firm and complete connection.
- 蛇口に接続: Thread the Click Seal faucet connector onto your faucet's supply line. Hand tighten the nut until you hear an audible click, indicating a secure seal. Plumbing tape is not needed for this threaded connection.
4. Operating the Faucet Connector
Once installed, the integrated stop valve allows you to control the water flow to your faucet.
- To Open Water Flow: Turn the handle on the stop valve to the 'open' position (typically aligned with the pipe).
- To Close Water Flow: Turn the handle on the stop valve to the 'closed' position (typically perpendicular to the pipe). This allows you to shut off water to the faucet without affecting the rest of your plumbing system.
5. メンテナンス
Regular inspection and proper care will ensure the longevity and reliable performance of your SharkBite Faucet Connector.
- 漏れ検査: Periodically check all connections for any signs of leaks. Address any leaks immediately by ensuring connections are secure.
- クリーニング： Clean the exterior of the connector with a soft, damp 布で拭いてください。仕上げを傷める可能性のある研磨剤入りの洗剤や溶剤の使用は避けてください。
- 切断: If you need to disconnect the fitting, use a SharkBite disconnect clip or disconnect tongs. Follow the specific instructions for these tools to avoid damaging the fitting or pipe.
6。 トラブルシューティング
このセクションでは、発生する可能性のある一般的な問題を取り上げ、解決策を示します。
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| Leak at push-to-connect end | Improper pipe preparation (burrs, scratches), insufficient insertion depth, damaged O-ring. | Ensure pipe is clean, deburred, and fully inserted to the mark. If problem persists, inspect O-ring for damage or replace fitting. |
| Leak at Click Seal faucet end | Nut not tightened sufficiently, damaged washer. | Hand tighten the Click Seal nut until an audible click is heard. Check the washer inside the nut for damage and replace if necessary. |
| Difficulty inserting pipe | Pipe not deburred, pipe not cut squarely, pipe type incompatibility. | Ensure pipe is properly deburred and cut squarely. Verify pipe material is compatible with SharkBite fittings. |
7. 仕様
Detailed technical specifications for the SharkBite 1/2 Inch Straight Stop Faucet Connector.
| 仕様 | 価値 |
|---|---|
| サイズ | 1/2 in. Straight Stop |
| 材料 | Stainless Steel (Hose), Brass (Fitting) |
| ブランド | シャークバイト |
| 色 | 銀 |
| 商品の寸法（長さ x 幅 x 高さ） | 21.15 x 1 x 5.01インチ |
| コネクタタイプ | カップリング |
| 外装仕上げ | 真鍮 |
| ねじの種類 | NPSM |
| アイテム重量 | 9.12オンス |
| 個数 | 1 |
| 欧州連合 | 697285246874 |
| 部品番号 | 24687 |
| モデル番号 | 24687 |
| 含まれるコンポーネント | Click Seal Faucet Connector |
| 承認 | CSA B125.1, NSF/ANSI 372, ASME A112.18.1, NSF/ANSI/CAN 61 |
8. 保証とサポート
All SharkBite valves, clips, joints, and adapters are manufactured and tested in the USA. The product comes with a manufacturer's warranty. For specific warranty details or technical support, please refer to the official SharkBite webサイトをご覧いただくか、カスタマー サービスに直接お問い合わせください。
連絡先：
- Webサイト： www.sharkbite.com
- 顧客サービス： 参照 website for phone numbers and contact forms.