1. はじめに
The Behringer TD-3-AM is an analog bass line synthesizer designed to produce rich bass and groove sounds. It features a pure analog signal path, authentic circuit reproduction with matched transistors, and a versatile 4-pole resonant filter. This manual provides essential information for setting up, operating, and maintaining your TD-3-AM synthesizer.
主な特徴:
- Analog Bass Line Synthesizer with true analog circuitry.
- Authentic reproduction of original circuits with matched transistors.
- Pure analog signal path based on legendary VCO, VCF, and VCA designs.
- Sawtooth and square wave VCO with transistor circuitry.
- 4-pole resonant filter with controls for cut-off, resonance, envelope, decay, and accent.
- Integrated 16-step sequencer for pattern creation.
- Built-in distortion effect.
- USB and MIDI connectivity for modern integration.
2. 安全に関する注意事項
Please read and follow these safety instructions to prevent damage to the unit and ensure your safety:
- ユニットを開けないでください。内部にはユーザーが修理できる部品はありません。修理はすべて資格のあるサービス担当者にご依頼ください。
- ユニットを雨、湿気、または極端な温度にさらさないでください。
- ユニットに付属の電源アダプタのみを使用してください。
- ユニット周囲の換気を良好に保ち、通気口を塞がないようにしてください。
- ユニットを熱源の近くや直射日光の当たる場所に置かないでください。
- 雷雨のときや長期間使用しない場合は、電源アダプターを外してください。
3.製品オーバーview
フロントパネルコントロール
The front panel of the TD-3-AM features various controls for sound shaping and sequencing:
画像: 正面 view of the Behringer TD-3-AM synthesizer, showing all knobs, buttons, and the main display area.
- テンポ： シーケンサーの再生速度を調整します。
- 波形： Selects between sawtooth and square wave for the VCO.
- 曲: Fine-tunes the pitch of the oscillator.
- 切り落とす： Controls the filter's cutoff frequency.
- 共振： Adjusts the filter's resonance.
- 封筒： Controls the amount of envelope modulation applied to the filter.
- 減衰： エンベロープの減衰時間を設定します。
- アクセント： アクセント付きの音符の強度を制御します。
- ねじれ： Activates and adjusts the built-in distortion effect.
- 音量： 全体の出力ボリュームをコントロールします。
- モードセレクター： Switches between Write, Play, Pattern, and Track modes for sequencing.
- Pitch Mode Buttons: Used for entering notes and setting pitch parameters.
- Time Mode Buttons: Used for setting note duration, accent, and slide.
- 開始/停止: シーケンサーの再生を開始または停止します。
背面パネルの接続
The rear panel provides essential input and output connections:
画像: 背面 view of the Behringer TD-3-AM synthesizer, showing the output, MIDI, USB, and power connections.
- 出力： 1/4-inch TS jack for audio output.
- MIDI 入力/出力/スルー: 5-pin DIN connectors for MIDI communication.
- USB： MIDI over USB およびファームウェア アップデート用の USB-B ポート。
- 電源DC入力: Connection for the 9V DC power adapter.
トップパネルの接続
Additional connections are located on the top panel for advanced integration:
画像: トップダウン view of the Behringer TD-3-AM synthesizer, highlighting the small jack connections for Filter In, Sync Out, CV Out, Gate Out, and Phones.
- Filter In: 3.5mm jack for external audio input to the filter.
- Sync Out: 3.5mm jack for sending clock synchronization signals.
- CV 出力: 3.5mm jack for sending control voltageシグナル。
- ゲートアウト: 3.5mm jack for sending gate signals.
- 携帯電話: ヘッドフォンモニタリング用の 3.5mm ステレオ ジャック。
4. セットアップ
Follow these steps to set up your Behringer TD-3-AM:
- 電源接続: Connect the supplied 9V DC power adapter to the 'Power DC Input' on the rear panel and plug it into a suitable power outlet.
- オーディオ出力: Connect the 'Output' jack on the rear panel to your mixer, audio interface, or amplifier using a 1/4-inch TS cable. For private monitoring, connect headphones to the 'Phones' jack on the top panel.
- MIDI/USB接続（オプション）:
- For MIDI control from an external device (e.g., MIDI keyboard, sequencer), connect the MIDI OUT of your device to the 'MIDI In' on the TD-3-AM.
- To control the TD-3-AM via a computer, connect a USB-B cable from the TD-3-AM's 'USB' port to your computer. The unit will be recognized as a MIDI device.
接続図:
Image: Diagram illustrating how to connect the TD-3-AM to a MIDI keyboard, computer via USB, audio interface, studio monitors, and headphones.
Image: Diagram showing the connection of the TD-3-AM to a keyboard ampサウンド出力用のリファイア。
Image: Diagram demonstrating how to connect headphones directly to the TD-3-AM for monitoring.
5.運用
基本操作:
- 電源オン: Ensure all connections are secure, then connect the power adapter to the mains. The unit will power on automatically.
- 音量調整: Start with the 'Volume' knob at a low setting and gradually increase it to a comfortable listening level.
- Sound Generation:
- Use the 'Waveform' switch to select between sawtooth and square wave.
- Adjust 'Tune', 'Cutoff', 'Resonance', 'Envelope', 'Decay', and 'Accent' knobs to sculpt your desired bass sound.
Sequencer Operation:
The TD-3-AM features a 16-step sequencer for creating and playing patterns.
- モード選択: Use the 'Mode' rotary switch to select between 'Write' (for programming patterns) and 'Play' (for playing patterns).
- Pattern/Track Selection: Use the 'Pattern Group' and 'Track' selectors to choose where to store or play your sequences.
- Writing a Pattern: In 'Write' mode, use the 'Pitch Mode' and 'Time Mode' buttons to enter notes, accents, and slides. Refer to the detailed instruction manual (available on the Behringer website) for advanced sequencing techniques.
- パターンの再生: In 'Play' mode, select your desired pattern and press 'Start/Stop' to begin playback. Adjust 'Tempo' to change the speed.
同期:
The TD-3-AM can synchronize with external devices via MIDI or analog clock:
- MIDI同期: The unit can receive MIDI clock signals from an external MIDI master device. Ensure the MIDI channel is correctly set (default is channel 1).
- アナログ同期: Use the 'Sync In' and 'Sync Out' jacks for synchronization with other analog gear.
6. メンテナンス
Proper maintenance ensures the longevity and optimal performance of your TD-3-AM:
- クリーニング： 本体の清掃には、柔らかく乾いた布をご使用ください。研磨剤入りの洗剤や溶剤は使用しないでください。
- ストレージ： When not in use, store the synthesizer in a cool, dry place, away from direct sunlight and extreme temperatures.
- ファームウェアの更新： 定期的にベリンガーをチェックする website for firmware updates. Updates can be installed via the USB connection using the Behringer Synth Tool software.
7。 トラブルシューティング
If you encounter issues with your TD-3-AM, refer to the following common troubleshooting steps:
| 問題 | 考えられる原因 | 解決 |
|---|---|---|
| 音声出力なし | Volume too low, incorrect audio connections, faulty cable. | Check 'Volume' knob. Verify all audio cables are correctly connected and functional. Ensure your amplifier/mixer is powered on and set to the correct input. |
| ユニットの電源が入らない | Power adapter not connected, faulty power adapter/outlet. | 電源アダプターが本体にしっかりと接続され、電源コンセントが機能していることを確認してください。別のコンセントをお試しください。 |
| シーケンサーが再生されない | Not in 'Play' mode, no pattern loaded, 'Start/Stop' not pressed. | Switch the 'Mode' to 'Play'. Ensure a pattern is selected. Press the 'Start/Stop' button. |
| MIDIコントロールが機能しない | Incorrect MIDI connections, wrong MIDI channel, driver issues (USB). | Verify MIDI cables are connected correctly (OUT to IN). Check the MIDI channel settings on both the TD-3-AM and your external controller (default is channel 1). For USB MIDI, ensure drivers are installed if required by your operating system. |
| Distortion effect not active | Distortion switch is OFF, 'Tone' or 'Level' knobs are at minimum. | Ensure the 'Distortion' switch is set to ON. Adjust the 'Tone' and 'Level' knobs to hear the effect. |
If the problem persists after trying these steps, please contact Behringer customer support.
8. 仕様
| 特徴 | 詳細 |
|---|---|
| ブランド | ベリンガー |
| モデル名 | TD-3-AM |
| 色 | メタリックイエロー |
| 材料 | Acrylonitrile Butadiene Styrene (Body Type: Metal) |
| アイテムの寸法（LxWxH） | 10 x 10 x 10 cm |
| アイテム重量 | 1.76 ポンド |
| コネクタタイプ | MIDI、USB |
| 含まれるコンポーネント | Power Adapter, Instruction Manual |
| 原産国 | 中国 |
| 世界貿易識別番号 | 04033653032261 |
| 部品番号 | P0ECM |
9. 保証
Warranty information for the Behringer TD-3-AM is typically provided with the product at the time of purchase or can be found on the official Behringer webサイトでご確認ください。保証請求の際に必要となりますので、購入証明書を保管してください。
10. サポート
For further assistance, technical support, or to download the latest firmware and software (such as the Behringer Synth Tool), please visit the official Behringer webサイト：
You may also find helpful resources and community forums on the Behringer support pages.