1.製品オーバーview
The HGM9510 controller is engineered for manual and automatic parallel system generators, accommodating units of similar or differing capacities. It supports single-unit constant power output and mains paralleling. This controller facilitates automatic start/stop, parallel running, data measurement, alarm protection, and remote control, measurement, and communication functions. Featuring a 4.3-inch TFT-LCD display, it offers multilingual interfaces (including English and Chinese) for user convenience. The controller integrates GOV (Engine Speed Governor) and AVR (Automatic Voltage Regulator) control functions for automatic synchronization and load sharing. It monitors engine status, indicating operational and fault conditions accurately. In case of abnormal conditions, it isolates the bus and shuts down the genset, displaying precise failure information on the LCD. An SAE J1939 interface allows communication with various ECU (Engine Control Unit) systems. Its 32-bit Microprocessor ensures precise parameter measurement, adjustment, and time settings. Most parameters are configurable via the front panel, or through a PC via USB or RS485 interfaces. Its compact structure, advanced circuits, simple connections, and high reliability make it suitable for various automatic gen-set control systems.
Figure 1.1: SmartGen HGM9510 Generator Controller Front Panel
Figure 1.2: Excerpt from HGM9510 Manual - Overview
2. Features and Characteristics
The HGM9510 controller offers a robust set of features designed for comprehensive generator management:
- Improved LCD wear-resistance and scratch resistance due to hard screen acrylic.
- RS485 通信ポートにより、ModBus プロトコルによるリモート制御、リモート測定、リモート通信が可能になります。
- Suitable for 3-phase 4-wire, 3-phase 3-wire, single phase 2-wire, and 2-phase 3-wire systems with voltage 120/240V and frequency 50/60Hz.
- Protection: automatic start/stop of the gen-set, ATS (Auto Transfer Switch) control with perfect fault indication and protection function.
- Can control engine heater, cooler, and fuel pump.
- ARM-based 32-bit SCM for high hardware integration and reliability.
- 480x272 LCD with backlight, multilingual interface (English, Chinese, etc.) selectable on-site.
- Silicon panel and pushbuttons for improved operation in high/low temperature environments.
- CANBUS port for communication with J1939 gensets, monitoring data (water temperature, oil pressure, engine speed, fuel consumption) and controlling start, stop, raising speed, and speed droop.
- Collects and displays 3-phase voltage, current, power parameter, and frequency of Bus/Mains.
- For Bus, controller has loss of phase and phase sequence wrong detection functions; for generator, controller has over voltage、volの下tage, over frequency, under frequency, over current, over power, reverse power, loss of phase, phase sequence wrong detection functions.
- Synchronization parameters: Voltage Difference Between Bus and Mains, Frequency Difference Between Bus and Mains, Phase Difference Between Bus and Mains.
- Multiple running modes in auto state: load running, off load running, demand parallel running.
- Ramp on and ramp off function.
- 3 fixed sensors (temperature, oil pressure, and liquid level).
- 2 configurable sensors can be set as sensor of temperature, oil pressure, or fuel level.
- More kinds of curves of temperature, oil pressure, fuel level can be used directly and users can define their own sensor curves.
- Precision measurement and display parameters about Engine, Temp. (WT) °C/°F (unit) both displayed, Oil pressure (OP) kPa/psi/bar(unit) all displayed, Fuel level (FL) %(unit), Speed (SPD) r/min(unit), Battery Voltage (VB) V (unit), Charger Voltage (VD) V (unit).
- Hour count (HC) can accumulate Max. 65535 hours. Start times can accumulate Max. 65535 times.
- パラメータ設定: パラメータは内部 EEPROM メモリに変更および保存でき、停電の場合でも失われません。tage; most of them can be adjusted using front panel of the controller and all of them can be modified using PC via USB or RS485 ports.
- Multiple crank disconnect conditions (speed sensor, oil pressure, generator frequency) are optional.
- 幅広い電源範囲DC（8〜35）V、さまざまな始動バッテリー容量に適していますtage環境。
- Event log, real-time clock, scheduled start & stop generator (can be set as start genset once a day/week/month whether with load or not).
- Accumulative total run time and total electric energy of A and B. Users can reset it as 0 and re-accumulate the value.
- With maintenance function. Actions (warning, trip and stop, shutdown) can be set when maintenance time out.
- All parameters used digital adjustment, instead of conventional analog modulation with normal potentiometer, more reliability and stability.
- IP55 waterproofness level can be achieved with the help of rubber-ring gasket between shell and control panel.
- Metal fixing clips enable perfect in high temperature environment.
- Modular design, self-extinguishing ABS plastic shell, pluggable terminal, built-in mounting, compact structure with easy installation.
Figure 2.1: Excerpt from HGM9510 Manual - Performance and Characteristics (Part 1)
Figure 2.2: Excerpt from HGM9510 Manual - Performance and Characteristics (Part 2)
2.1 Module Comparison
The HGM9510 offers advanced features compared to other models in the series:
Figure 2.3: Module Comparison Table
3. 技術仕様
| パラメータ | 詳細 |
|---|---|
| ワーキングVoltage | DC8.0V to 35.0V, uninterruptible power supply |
| 全体的な消費 | <4W (スタンバイモード: ≤2W) |
| AC Input (3 Phase 4 Wire) | AC 15V - 360V (ph-N) |
| AC Input (3 Phase 3 Wire) | AC 30V - 620V (ph-ph) |
| AC Input (Single Phase 2 Wire) | AC 15V - 360V (ph-N) |
| AC Input (2 Phase 3 Wire) | AC 15V - 360V (ph-N) |
| オルタネーター周波数 | 50Hz/60Hz |
| スピードセンサーボリュームtage | 1.0V～24V (RMS) |
| 速度センサー周波数 | 最大10,000Hz |
| リレー出力開始 | 16A DC28V power supply output |
| 燃料リレー出力 | 16A DC28V power supply output |
| Flexible Relay Output 1 | 7A DC28V power supply output |
| Flexible Relay Output 2 | 7A DC28V power supply output |
| Flexible Relay Output 3 | 7A DC28V power supply output |
| Flexible Relay Output 4 | 7A 250VAC passive output |
| Flexible Relay Output 5 | 7A 250VAC passive output |
| Flexible Relay Output 6 | 7A 250VAC passive output |
| ケース寸法 | 266mm x 182mm x 45mm |
| パネルカットアウト | 214mm×160mm |
| CT二次電流 | 定格 5A |
| 労働条件 | Temperature: (-25~+70)°C, Humidity: (20~93)%RH |
| 保管条件 | 温度: (-30~+80)°C |
| 保護レベル | IP55ガスケット |
| 断熱強度 | AC2.2kV vol を適用tagハイボリューム間tage端子と低音量tage端末; 漏れ電流は 3 分間で 1mA 以下です。 |
| 重さ | 0.95kg |
Figure 3.1: Excerpt from HGM9510 Manual - Technical Specifications
4. Installation and Wiring Diagram
Proper installation and wiring are crucial for the safe and correct operation of the HGM9510 controller. Refer to the typical application diagram below for connection details. Ensure all connections are secure and follow local electrical codes.
Figure 4.1: HGM9510 Typical Application Wiring Diagram
注記： Fuse F1: min. 2A; max. 20A. Fuse F2: max. 32A. Users should select suitable fuses depending on the practical application.
5. 操作
5.1 表示灯
The HGM9510 controller features several indicator lights on its front panel to provide immediate feedback on the system's status. Understanding these indicators is essential for monitoring and troubleshooting.
Figure 5.1: Indicator Lights and Their Functions
Warning indicator and Alarm indicator description:
| アラームタイプ | 警告インジケータ | アラームインジケーター |
|---|---|---|
| 警告 | ゆっくり点滅 | ゆっくり点滅 |
| トリップアラーム | ゆっくり点滅 | ゆっくり点滅 |
| シャットダウンアラーム | オフ | 高速点滅 |
| Trip and Stop Alarm | オフ | 高速点滅 |
実行インジケーター: Illuminated from crank disconnect to ETS while off during other periods.
Generator normal light: It is lit when the generator state is normal; flashing when the generator state is abnormal; off when there is no generator power.
6. メンテナンス
Regular maintenance ensures the longevity and reliable operation of your SmartGen HGM9510 controller. Perform the following checks periodically:
- 目視検査: Check for any signs of damage, loose connections, or corrosion on the controller and its wiring.
- クリーニング： コントローラーのディスプレイとボタンは、柔らかく乾いた布で拭いて清潔に保ってください。研磨剤入りの洗剤や溶剤の使用は避けてください。
- ファームウェアの更新： メーカーの web最適なパフォーマンスと新機能へのアクセスを確保するために、利用可能なファームウェア アップデートをサイトから確認してください。
- パラメータ再view: 定期的に再view the controller's settings to ensure they align with your generator system's requirements.
- 環境条件: 損傷を防ぐために、動作環境が指定された温度と湿度の範囲内であることを確認してください。
7。 トラブルシューティング
If you encounter issues with your HGM9510 controller, consider the following basic troubleshooting steps:
- 電源なし: Verify the DC power supply connections and ensure the voltage is within the specified range (DC8.0V to 35.0V). Check for blown fuses (F1, F2 as per wiring diagram).
- 表示の問題: If the display is blank or unreadable, check power supply. If power is present, contact support.
- Generator Not Starting/Stopping: Check all wiring connections to the generator, including start/stop relays, fuel pump, and speed sensor. Verify that all protection functions are correctly configured and not preventing operation.
- Communication Errors (RS485/CANBUS): Ensure communication cables are correctly connected and terminated. Verify communication settings in the controller and connected devices.
- アラーム表示: Refer to the 'Indicator Lights' section (5.1) to identify the type of alarm. Consult the full manual for specific alarm codes and their remedies.
- 間違った読み方: Check sensor connections and calibration. Ensure the correct sensor type is selected in the controller's parameters.
For complex issues or persistent problems, it is recommended to consult the comprehensive SmartGen HGM9510 user manual or contact SmartGen technical support.
8. 保証とサポート
The SmartGen HGM9510 Generator Controller is backed by a manufacturer's warranty. Please refer to the warranty card included with your product or visit the official SmartGen web詳細な保証条件については、サイトをご覧ください。
For technical assistance, product support, or service inquiries, please contact SmartGen customer service or your authorized dealer. You can typically find contact information on the SmartGen official webサイト： www.smartgen.cn
When contacting support, please have your product model (HGM9510) and any relevant purchase information ready to facilitate faster service.